--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.22-2-686: Belkin F5D7050 v.4002 wireless USB adapter fails to communicate.
- From: David Keegan <dksw@eircom.net>
- Date: Sat, 15 Sep 2007 23:49:11 +0100
- Message-id: <20070915224911.4721.95440.reportbug@dk.dks.ie>
Package: linux-image-2.6.22-2-686
Version: 2.6.22-4
Severity: normal
When the device is plugged in the zd1211rw driver loads
automatically without errors in dmesg or /var/log/messages
and I can see details of the wireless router using iwconfig
and iwlist scan. However attempts to ping the router fail
with "No route to host". Ifconfig output indicates frame
errors receiving packets and some errors sending packets.
Adapter works fine from WinXp box to same wireless router,
so hardware should be ok.
On plugging the USB wireless adapter dmesg:
usb 5-1: new high speed USB device using ehci_hcd and address 7
usb 5-1: configuration #1 chosen from 1 choice
usb 5-1: reset high speed USB device using ehci_hcd and address 7
zd1211rw 5-1:1.0: firmware version 4725
zd1211rw 5-1:1.0: zd1211b chip 050d:705c v4810 high 00-17-3f AL2230_RF pa0 g--NS
zd1211rw 5-1:1.0: eth1
usbcore: registered new interface driver zd1211rw
udev: renamed network interface eth1 to eth3
After ifup eth3 /var/log/messages:
ADDRCONF(NETDEV_UP): eth3: link is not ready
Tried ifconfig first:
ifdown eth3
ifconfig eth3 up
Sep 15 22:17:30 dk kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
ifup eth3
Sep 15 22:17:54 dk kernel: SoftMAC: Open Authentication completed with 00:17:3f:a9:ef:2f
Sep 15 22:17:54 dk kernel: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
iwconfig:
eth3 IEEE 802.11b/g ESSID:"foinnse" Nickname:"zd1211"
Mode:Auto Frequency:2.412 GHz Access Point: 00:17:3F:A9:EF:2F
Bit Rate=24 Mb/s
Encryption key:off
Link Quality=99/100 Signal level=73/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
iwlist scan:
eth3 Scan completed :
Cell 01 - Address: 00:17:3F:A9:EF:2F
ESSID:"foinnse"
Protocol:IEEE 802.11bg
Mode:Master
Channel:1
Frequency:2.412 GHz (Channel 1)
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 9 Mb/s; 11 Mb/s
6 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=100/100 Signal level=5/100
Extra: Last beacon: 12ms ago
eth3 Link encap:Ethernet HWaddr 00:17:3F:B0:8B:00
inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::217:3fff:feb0:8b00/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:36 dropped:0 overruns:0 frame:36
TX packets:52 errors:6 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:2517 (2.4 KiB)
ping 192.168.2.1 (wireless router):
PING wr.dks.ie (192.168.2.1) 56(84) bytes of data.
>From dkw.dks.ie (192.168.2.5) icmp_seq=1 Destination Host Unreachable
>From dkw.dks.ie (192.168.2.5) icmp_seq=2 Destination Host Unreachable
>From dkw.dks.ie (192.168.2.5) icmp_seq=5 Destination Host Unreachable
>From dkw.dks.ie (192.168.2.5) icmp_seq=6 Destination Host Unreachable
>From dkw.dks.ie (192.168.2.5) icmp_seq=9 Destination Host Unreachable
>From dkw.dks.ie (192.168.2.5) icmp_seq=10 Destination Host Unreachable
-- Package-specific info:
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (500, 'stable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.21-2-686 (SMP w/1 CPU core)
Locale: LANG=en_IE.UTF-8@euro, LC_CTYPE=en_IE.UTF-8@euro (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-2-686 depends on:
ii initramfs-tools [linux-initr 0.90a tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-2-686 recommends:
ii libc6-i686 2.6.1-1+b1 GNU C Library: Shared libraries [i
-- debconf information excluded
--- End Message ---