--- Begin Message ---
- To: submit@bugs.debian.org
- Subject: linux-image-2.6.22-3-k7: does not discover RAID and EVMS/LVM2 volumes
- From: "Dr. Oliver Muth" <Dr.O.Muth@gmx.de>
- Date: Thu, 20 Dec 2007 09:46:18 +0100
- Message-id: <1198140379.11430.2.camel@athlon-9.bjoernsjoe>
- Reply-to: Dr.O.Muth@gmx.de
Package: linux-image-2.6.22-3-k7
Version: 2.6.22-6
Severity: normal
*** Please type your report below this line ***
Hi!
I am running a RAID1 with two harddrives connected to two different
controllers.
The system works fine with 2.6.18 or older.
When I was trying out 2.6.22 by booting from my "experimental" lenny
partition on a third harddrive,
the kernel discovers the first harddrive on the first controller, then
continues to discover USB and IDE,
while the second controller performs its domain validation.
Then it starts the RAID 1 just immediately before the two other
harddrives are discovered.
When the other harddrives on the second controller are being discovered,
the second harddrive
does not get added to the mirror - the mirror is already started in
degraded mode.
8<------8<-------8<------
md: raid1 personality registered for level 1
md: md1 stopped.
md: bind<sda6>
raid1: raid set md1 active with 1 out of 3 mirrors
sd 1:0:1:0: [sdb] 71687340 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: cb 00 00 08
sd 1:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:1:0: [sdb] 71687340 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: cb 00 00 08
sd 1:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
8<------8<------8<------
A bit later a large number of device-mapper errors follow, like this:
8<------8<------8<------
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@redhat.com
device-mapper: table: 253:1: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
8<------8<------8<------
When the system is up, md1 is active with one disk (sda6), sdc6 is now
dm-0, and I have to manually add
dm-0 to rebuild the mirror.
ALL named EVMS volumes are missing in /dev/evms. When I start the EVMS
GUI they are discovered and all
marked "modified", but the attempt to save the modifications yields in
the error message that EVMS could
not save because it could not find the devices.
I hope this helps. Please let me know what more information I should
provide.
Best regards
Oliver
-- Package-specific info:
** Version:
Linux version 2.6.22-3-k7 (Debian 2.6.22-6) (maks@debian.org) (gcc
version 4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Mon Nov 12
09:12:50 UTC 2007
** Tainted: P (1)
** Kernel log:
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
device-mapper: table: 253:3: linear: dm-linear: Device lookup failed
device-mapper: ioctl: error adding target to table
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
PPP generic driver version 2.4.2
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 24
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
eth0: no IPv6 routers present
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13
18:21:22 PDT 2007
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
ip_tables: (C) 2000-2006 Netfilter Core Team
md: bind<dm-0>
RAID1 conf printout:
--- wd:1 rd:3
disk 0, wo:1, o:1, dev:dm-0
disk 1, wo:0, o:1, dev:sda6
md: recovery of RAID array md1
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000
KB/sec) for recovery.
md: using 128k window, over a total of 70894720 blocks.
** Loaded modules:
Module Size Used by
xt_TCPMSS 4992 1
xt_tcpmss 2496 1
xt_tcpudp 3392 1
iptable_mangle 3136 1
ip_tables 12708 1 iptable_mangle
x_tables 14660 4 xt_TCPMSS,xt_tcpmss,xt_tcpudp,ip_tables
nvidia 7249460 34
ppdev 8964 0
lp 11300 0
button 8208 0
ac 5508 0
battery 10308 0
pppoe 13888 2
pppox 4168 1 pppoe
ipv6 239524 10
ppp_generic 26580 6 pppoe,pppox
slhc 6464 1 ppp_generic
dm_snapshot 17252 0
dm_mirror 21376 0
dm_mod 52672 7 dm_snapshot,dm_mirror
loop 17412 0
snd_via82xx 27224 1
gameport 15304 1 snd_via82xx
snd_ac97_codec 93220 1 snd_via82xx
ac97_bus 2560 1 snd_ac97_codec
snd_pcm_oss 39904 0
snd_mixer_oss 15872 1 snd_pcm_oss
snd_pcm 72772 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 10376 2 snd_via82xx,snd_pcm
snd_mpu401_uart 8384 1 snd_via82xx
snd_seq_dummy 4036 0
snd_seq_oss 29760 0
tsdev 8320 0
snd_seq_midi 8480 0
snd_seq_midi_event 7360 2 snd_seq_oss,snd_seq_midi
snd_seq 46864 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 21380 2 snd_pcm,snd_seq
snd_rawmidi 23264 2 snd_mpu401_uart,snd_seq_midi
snd_seq_device 8012 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
serio_raw 7044 0
rtc 13144 0
pcspkr 3392 0
snd 48804 13
snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_seq,snd_timer,snd_rawmidi,snd_seq_device
psmouse 36432 0
parport_pc 34212 1
parport 34312 3 ppdev,lp,parport_pc
usblp 13632 0
via_ircc 24788 0
irda 173180 1 via_ircc
crc_ccitt 2432 1 irda
i2c_viapro 8788 0
i2c_core 24000 2 nvidia,i2c_viapro
soundcore 7840 1 snd
shpchp 31380 0
pci_hotplug 29568 1 shpchp
via_agp 10304 1
agpgart 32264 2 nvidia,via_agp
evdev 9664 4
ext3 122696 1
jbd 55848 1 ext3
mbcache 8580 1 ext3
raid1 22784 1
md_mod 74196 3 raid1
ide_cd 36896 0
cdrom 33184 1 ide_cd
generic 5124 0 [permanent]
via82cxxx 8964 0 [permanent]
ide_core 114436 3 ide_cd,generic,via82cxxx
sd_mod 27584 6
via_rhine 24136 0
mii 5696 1 via_rhine
floppy 55332 0
ata_generic 7876 0
libata 117232 1 ata_generic
ehci_hcd 31116 0
uhci_hcd 23376 0
usbcore 126024 4 usblp,ehci_hcd,uhci_hcd
aic7xxx 157592 6
scsi_transport_spi 23424 1 aic7xxx
scsi_mod 137356 4 sd_mod,libata,aic7xxx,scsi_transport_spi
thermal 13768 0
processor 31560 1 thermal
fan 5124 0
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8366/A/7 [Apollo
KT266/A/333] [1106:3099]
Subsystem: ASRock Incorporation K7VT2 motherboard [1849:3099]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8366/A/7 [Apollo
KT266/A/333 AGP] [1106:b099] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dbe00000-dfefffff
Prefetchable memory behind bridge: bbd00000-dbcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:0b.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m
[9005:0080] (rev 02)
Subsystem: Adaptec 29160LP Low Profile Ultra160 SCSI Controller
[9005:e220]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
BIST result: 00
Region 0: I/O ports at ec00 [disabled] [size=256]
Region 1: Memory at dffff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at dffc0000 [disabled] [size=128K]
Capabilities: <access denied>
00:0c.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m
[9005:0080] (rev 02)
Subsystem: Adaptec 29160N Ultra160 SCSI Controller [9005:62a0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
BIST result: 00
Region 0: I/O ports at e800 [disabled] [size=256]
Region 1: Memory at dfffe000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at dffa0000 [disabled] [size=128K]
Capabilities: <access denied>
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 4: I/O ports at dc00 [size=32]
Capabilities: <access denied>
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0
[1106:3104] (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 18
Region 0: Memory at dfffdf00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge
[1106:3177]
Subsystem: ASRock Incorporation K7VT2 motherboard [1849:3177]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:11.1 IDE interface [0101]: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev
06) (prog-if 8a [Master SecP PriP])
Subsystem: ASRock Incorporation K7VT2/K7VT6 motherboard [1849:0571]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 255
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: <access denied>
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 50)
Subsystem: VIA Technologies, Inc. K7VT2 motherboard [1106:4161]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 20
Region 0: I/O ports at d800 [size=256]
Capabilities: <access denied>
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102
[Rhine-II] [1106:3065] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at dfffde00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
01:00.0 VGA compatible controller [0300]: nVidia Corporation GeForce
7600 GS [10de:02e1] (rev a2) (prog-if 00 [VGA])
Subsystem: Giga-byte Technology Unknown device [1458:3428]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at dd000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at dfee0000 [disabled] [size=128K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-3-k7 (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-k7 depends on:
ii initramfs-tools [linux-initr 0.91c tools for generating an
initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.22-3-k7 recommends:
ii libc6-i686 2.7-3 GNU C Library: Shared
libraries [i
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-k7/preinst/failed-to-move-modules-2.6.22-3-k7:
linux-image-2.6.22-3-k7/postinst/depmod-error-2.6.22-3-k7: false
linux-image-2.6.22-3-k7/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-k7/prerm/removing-running-kernel-2.6.22-3-k7:
true
linux-image-2.6.22-3-k7/preinst/already-running-this-2.6.22-3-k7:
linux-image-2.6.22-3-k7/prerm/would-invalidate-boot-loader-2.6.22-3-k7:
true
linux-image-2.6.22-3-k7/postinst/old-system-map-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/old-dir-initrd-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/kimage-is-a-directory:
linux-image-2.6.22-3-k7/preinst/overwriting-modules-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/create-kimage-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/preinst/initrd-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/abort-install-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/lilo-initrd-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/depmod-error-initrd-2.6.22-3-k7:
false
linux-image-2.6.22-3-k7/postinst/old-initrd-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/preinst/elilo-initrd-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/bootloader-error-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/abort-overwrite-2.6.22-3-k7:
linux-image-2.6.22-3-k7/postinst/bootloader-test-error-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/bootloader-initrd-2.6.22-3-k7: true
--- End Message ---