--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.24-1-amd64: Update from 2.6.24-6 to 2.6.24-7 failed to execute "lilo" causing boot loop
- From: Adolf Winterer <adolf.j.winterer@inn-salzach.de>
- Date: Sat, 24 May 2008 10:50:10 +0200
- Message-id: <20080524085010.4670.80858.reportbug@pandora.site>
Package: linux-image-2.6.24-1-amd64
Version: 2.6.24-7
Severity: normal
Updating the system from 2.6.24-6 to 2.6.24-7 rendered the system unuseable.
After the reboot lilo started but was not able to load the kernel, the
system rebooted, entering an infinite boot loop. The update had been done
with synaptic.
Fix:
Booting from the install CD into the rescue mode, mounting the root partition
and the boot partition (root and boot live in different partitions here) and
issuing the command "lilo" allowed the system to boot normal again.
Afterwards I remembered that I had seen no "lilo" command in synaptics
terminal window.
Previous kernel updates within the 2.6.24 kernel series had not shown this
defect.
-- Package-specific info:
** Version:
Linux version 2.6.24-1-amd64 (Debian 2.6.24-7) (dannf@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Sat May 10 09:28:10 UTC 2008
** Command line:
auto BOOT_IMAGE=Linux ro root=803
** Tainted: P (1)
** Kernel log:
skge 1.13 addr 0xfdef8000 irq 19 chip Yukon-Lite rev 9
skge eth0: addr 00:30:1b:42:98:ad
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xfa00 ctl 0xf900 bmdma 0xf600 irq 19
ata2: SATA max UDMA/133 cmd 0xf800 ctl 0xf700 bmdma 0xf608 irq 19
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
ata1.00: ATA-7: ST3400833NS, 3.AEH, max UDMA/133
ata1.00: 781422768 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3400833NS 3.AE PQ: 0 ANSI: 5
ICH7: IDE controller (0x8086:0x27df rev 0x01) at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:pio
ICH7: IDE port disabled
Probing IDE interface ide0...
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
firewire_core: created new fw device fw0 (0 config rom retries, S400)
hda: _NEC DVD_RW ND-4571A, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input2
pnp: the driver 'parport_pc' has been registered
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
parport_pc 00:07: driver attached
input: Power Button (FF) as /class/input/input3
intel_rng: FWH not detected
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
input: ImExPS/2 Generic Explorer Mouse as /class/input/input5
Adding 2931852k swap on /dev/sda2. Priority:-1 extents:1 across:2931852k
EXT3 FS on sda3, internal journal
loop: module loaded
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.12 Thu Feb 14 17:51:09 PST 2008
fuse init (API version 7.9)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
skge eth0: enabling interface
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
skge eth0: Link is up at 1000 Mbps, full duplex, flow control both
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
eth0: no IPv6 routers present
NET: Registered protocol family 4
NET: Registered protocol family 3
NET: Registered protocol family 5
** Loaded modules:
Module Size Used by
appletalk 42384 2
ax25 62468 2
ipx 33736 2
p8023 6656 1 ipx
binfmt_misc 17292 1
rfcomm 46240 2
l2cap 29568 9 rfcomm
bluetooth 65956 4 rfcomm,l2cap
ppdev 13832 0
lp 17476 0
ac 11400 0
battery 19976 0
ipv6 286248 35
microcode 16792 0
firmware_class 15104 1 microcode
fuse 53680 1
nvidia 8855748 24
firewire_sbp2 20624 0
loop 22788 0
snd_hda_intel 362152 1
snd_pcm_oss 46624 0
snd_mixer_oss 21376 1 snd_pcm_oss
snd_pcm 89352 2 snd_hda_intel,snd_pcm_oss
snd_timer 28552 1 snd_pcm
i2c_i801 14108 0
snd 65896 7 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
i2c_core 29824 2 nvidia,i2c_i801
soundcore 13216 1 snd
button 13984 0
psmouse 45724 0
snd_page_alloc 15248 2 snd_hda_intel,snd_pcm
iTCO_wdt 17488 0
intel_agp 32288 0
parport_pc 42408 1
parport 44812 3 ppdev,lp,parport_pc
serio_raw 11908 0
evdev 17024 3
pcspkr 7808 0
ext3 139024 3
jbd 55976 1 ext3
mbcache 13952 1 ext3
dm_mirror 27008 0
dm_snapshot 21960 0
dm_mod 67832 5 dm_mirror,dm_snapshot
ide_cd 44704 0
cdrom 39464 1 ide_cd
sd_mod 33536 5
piix 13316 0 [permanent]
generic 9732 0 [permanent]
ide_core 144920 3 ide_cd,piix,generic
ata_piix 25348 5
ata_generic 13060 0
skge 47248 0
firewire_ohci 24192 0
firewire_core 49472 2 firewire_sbp2,firewire_ohci
crc_itu_t 6656 1 firewire_core
libata 162992 2 ata_piix,ata_generic
scsi_mod 170296 3 firewire_sbp2,sd_mod,libata
ehci_hcd 39692 0
uhci_hcd 30112 0
thermal 22688 0
processor 45032 1 thermal
fan 9864 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port [8086:2771] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-fcffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at ff00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at fe00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at fd00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at fc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fb00 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: ata_generic, generic, piix
00:1f.2 IDE interface [0101]: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at fa00 [size=8]
Region 1: I/O ports at f900 [size=4]
Region 2: I/O ports at f800 [size=8]
Region 3: I/O ports at f700 [size=4]
Region 4: I/O ports at f600 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix, ata_generic, generic
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3093]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 VGA compatible controller [0300]: nVidia Corporation G70 [GeForce 7600 GS] [10de:0392] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:8214]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at df00 [size=128]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
02:0a.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. IEEE 1394 Host Controller [1106:3044] (rev c0) (prog-if 10)
Subsystem: Elitegroup Computer Systems Device [1019:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ef00 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
02:0b.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:5093]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 23 (5750ns min, 7750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fdef8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at ec00 [size=256]
[virtual] Expansion ROM at fdd00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge
Kernel modules: skge
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.24-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.24-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.21 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92a tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.24-1-amd64 recommends no packages.
-- debconf information:
linux-image-2.6.24-1-amd64/preinst/abort-overwrite-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-dir-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/failed-to-move-modules-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/bootloader-test-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/create-kimage-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-initrd-2.6.24-1-amd64: false
linux-image-2.6.24-1-amd64/preinst/overwriting-modules-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/bootloader-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.24-1-amd64/preinst/bootloader-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/initrd-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/prerm/removing-running-kernel-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-2.6.24-1-amd64: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-1-amd64/preinst/lilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/old-system-map-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.24-1-amd64/preinst/abort-install-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/prerm/would-invalidate-boot-loader-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/elilo-initrd-2.6.24-1-amd64: true
--- End Message ---