--- Begin Message ---
- To: <submit@bugs.debian.org>
- Subject: linux-image-2.6.17-2-686: confirm fault with serial console
- From: Vincent McIntyre <Vince.McIntyre@atnf.csiro.au>
- Date: Mon, 25 Sep 2006 14:35:31 +1000 (EST)
- Message-id: <Pine.SOL.4.33.0609251427490.14796-100000@venice.tip.CSIRO.AU>
Followup-For: Bug #386497
Package: linux-image-2.6.17-2-686
*** Please type your report below this line ***
See also bugs 380188, 383264
I attempted to boot linux-image-2.6.17-2-686-bigmem and also had this
failure. This kernel was from backports.org, _but_ only these changes had
been made:
linux-2.6 (2.6.17-8~bpo.1) sarge-backports; urgency=low
* Rebuilt for sarge.
* Built using gcc-3.3 and python2.4.
* Disabled ABI check.
-- Norbert Tretkowski <nobse@backports.org> Tue, 5 Sep 2006 19:19:31 +0200
so I think it is worth following up to this bug.
I will of course send this report to the backports people too.
Note that linux-image-2.6.16-2-686-smp from the same source worked
(same level of changes, just a recompile basically).
The console message right before the hang was
ts: Compaq touchscreen protocol output
The first few lines after that are
BUG: unable to handle kernel NULL pointer dereference at virtual address 0000000c
printing eip:
c020ab74
*pde = 039a5001
*pre = 00000000
Oops: 0000 [#1]
SMP
Modules linked in: tsdev sg psmouse hw_random mousedev serio_raw
shpchp e752_edac edac_mc 8250_pnp ide_floppy pci_hotplug joydev evdev
8250_pci pcspkr rtc floppy ext3 jbd mbcache ide_cd cdrom siimage piix
sd_mod usbhid generic ehci_hcd mptfc mptscsih uhci_hcd megaraid_mbox
mptbase scsi_transport_fc megaraid_mm usbcore e1000 scsi_mod thermal
processor fan
CPU: 0
EIP 0060 [<c020ab74>] Not tainted VLI
EFLAGS 00010206 (2.6.17-2-686-bigmem #1)
EIP is at uart_write_room+0x9/0x16
The hardware is: Dell PE1850 with dual CPU, 4096Mb memory, Bios rev A00.
I am not using the bpo libc6-i686 package.
dpkg -l |grep libc6
ii libc6 2.3.2.ds1-22sa GNU C Library: Shared libraries and Timezone
ii libc6-dev 2.3.2.ds1-22sa GNU C Library: Development Libraries and Hea
ii xviewg 3.2p1.4-19 XView shared libraries [libc6]
This is a SMP-aware kernel,
% grep SMP /boot/config-2.6.17-2-686-bigmem
CONFIG_SMP=y
# CONFIG_X86_BIGSMP is not set
CONFIG_SUSPEND_SMP=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_SMP=y
I have the hardware attached to a KVM and the serial port connected to a
serial concentrator.
The relevant bits of /boot/grub/menu.lst are
serial --unit=0 --speed=9600 --word=8 --parity=no --stop=1
terminal --timeout=5 console serial
kernel /boot/vmlinuz-2.6.17-2-686-bigmem root=/dev/sda2 ro console=tty0 console=ttyS0,9600
I saw the comment about blacklisting 8250_pnp but did not try this.
I have hotplug-utils and udev installed, I don't understand why
/etc/hotplug should have anything to do with this problem but perhaps it
does. FWIW,
% ls /etc/hotplug/blacklist.d
libsane
This file belongs to the (sarge) libsane package and should have no
relevance to this discussion.
% dpkg -l udev
ii udev 0.100-1~bpo.1 /dev/ and hotplug management daemon
-- System Information:
Debian Release: 3.1
Architecture: i386 (i686)
Kernel: Linux 2.6.16-2-686-smp
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
--- End Message ---