Bug#479114: kernel memory mapping bug
package: kernel
version: 2.6.22, 2.6.24
Attempting to install Lenny using netinstall.
The hardware:
MSI K9A2 CF mainboard w/AMD 790X chipset, AMI BIOS 2.61, Realtek 81xx
Gigabit Ethernet, Athlon X2 5400+, 2 X 1 GB Kingston DDR2 667. This bug
is identical using an ECS A780GM-A Black series mainboard with AMD 780G
chipset and the same AMI BIOS version 2.61.
Upon install I get the following error;
PCI: BIOS BUG: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG
PCI: Cannot allocate resource region 3 of device 0000:00:00
Using 'installgui' configuration of Realtek Ethernet fails. Works with
normal install. This may be a seperate issue.
It appears that the kernel is not properly mapping memory. Booting
ubuntu 8.04 works fine. Memory is properly mapped and working fine. Same
with Mandriva live CD. Ran memtest and memory showed no problems.
I did manage to get lenny installed but the kernel only sees half of the
memory and the system is very sluggish.
Here is the output of 'dmesg | grep -i memory';
Freeing initrd memory: 6389k freed
Total HugeTLB memory allocated, 0
Freeing unused kernel memory: 324k freed
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Following is the output of 'dmesg';
reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
system 00:0d: iomem range 0xfed45000-0xffffffff could not be reserved
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: fc000000-fe9fffff
PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:06.0
IO window: e000-efff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:14.4
IO window: disabled.
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6389k freed
audit: initializing netlink socket (disabled)
audit(1209680603.628:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 324k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: duty_cycle spans bit 4
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xf8826000, 00:1d:92:a1:6f:d9, XID 38000000 IRQ
221
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 17, io mem 0xfbffe000
libata version 3.00 loaded.
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 18, io mem 0xfbffd000
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.2: irq 16, io mem 0xfbffc000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using ohci_hcd and address 2
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.3: irq 18, io mem 0xfbffb000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.4: irq 16, io mem 0xfbffa000
usb 1-1: configuration #1 chosen from 1 choice
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ahci 0000:00:12.0: version 3.0
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 19
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP
usb 4-2: new full speed USB device using ohci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
hub 4-2:1.0: USB hub found
hub 4-2:1.0: 7 ports detected
usb 4-2.2: new full speed USB device using ohci_hcd and address 3
usb 4-2.2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA
mode
ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xfbfff800 port 0xfbfff900 irq 19
ata2: SATA max UDMA/133 abar m1024@0xfbfff800 port 0xfbfff980 irq 19
ata3: SATA max UDMA/133 abar m1024@0xfbfff800 port 0xfbfffa00 irq 19
ata4: SATA max UDMA/133 abar m1024@0xfbfff800 port 0xfbfffa80 irq 19
usb 4-2.3: new full speed USB device using ohci_hcd and address 4
usb 4-2.3: configuration #1 chosen from 1 choice
usb 4-2.4: new full speed USB device using ohci_hcd and address 5
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: WDC WD800JD-00LUA0, 06.01D06, max UDMA/133
ata1.00: 156301488 sectors, multi 16: LBA48
ata1.00: configured for UDMA/133
usb 4-2.4: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
hiddev96hidraw0: USB HID v1.00 Device [Cypress Semiconductor USB to
Serial] on usb-0000:00:13.0-1
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi5 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3500630AS, 3.AFM, max UDMA/133
ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD800JD-00LU 06.0 PQ: 0
ANSI: 5
scsi 1:0:0:0: Direct-Access ATA ST3500630AS 3.AF PQ: 0
ANSI: 5
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 20
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 20, io mem 0xfbfff000
usb 1-1: USB disconnect, address 2
Driver 'sd' needs updating - please use bus_type methods
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 10 ports detected
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1 sdb2 < sdb5 sdb6>
sd 1:0:0:0: [sdb] Attached SCSI disk
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot
0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
SB600_PATA: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
usb 4-2: USB disconnect, address 2
usb 4-2.2: USB disconnect, address 3
usb 4-2.3: USB disconnect, address 4
usb 4-2.4: USB disconnect, address 5
usb 6-8: new high speed USB device using ehci_hcd and address 3
usb 6-8: configuration #1 chosen from 1 choice
hub 6-8:1.0: USB hub found
hub 6-8:1.0: 7 ports detected
hdb: BENQ DVD LS DW1655, ATAPI CD/DVD-ROM drive
usb 6-8.2: new high speed USB device using ehci_hcd and address 4
usb 6-8.2: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb 6-8.3: new high speed USB device using ehci_hcd and address 5
hda: LITE-ON DVD SHD-16P1S, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 21 (level, low) -> IRQ 21
hda: ATAPI 48X DVD-ROM drive, 1725kB Cache
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
firewire_ohci: Added fw-ohci device 0000:03:03.0, OHCI version 1.0
usb 6-8.3: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Attempting manual resume
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 6-8.4: new full speed USB device using ehci_hcd and address 6
usb 6-8.4: configuration #1 chosen from 1 choice
firewire_core: created new fw device fw0 (0 config rom retries, S400)
usb 1-1: new low speed USB device using ohci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
hiddev96hidraw0: USB HID v1.00 Device [Cypress Semiconductor USB to
Serial] on usb-0000:00:13.0-1
Linux agpgart interface v0.102
input: Power Button (FF) as /class/input/input1
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
usblp0: USB Bidirectional printer dev 6 if 1 alt 0 proto 2 vid 0x03F0
pid 0x4F11
usbcore: registered new interface driver usblp
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 20 (level, low) -> IRQ 22
saa7133[0]: found at 0000:03:02.0, rev: 209, irq: 22, latency: 64, mmio:
0xfebff800
saa7133[0]: subsystem: 1462:8626, board: UNKNOWN/GENERIC
[card=0,autodetected]
saa7133[0]: board init: gpio is 100
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input3
saa7133[0]: i2c eeprom 00: 62 14 26 86 10 28 ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
logips2pp: Detected unknown logitech mouse model 127
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
input: ImExPS/2 Logitech Explorer Mouse as /class/input/input4
usb-storage: device scan complete
scsi 6:0:0:0: Direct-Access WD 5000AAV External 1.65 PQ: 0
ANSI: 4
sd 6:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 6:0:0:0: [sdc] Attached SCSI disk
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access WD 3200AAJ External 1.65 PQ: 0
ANSI: 0
sd 7:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 7:0:0:0: [sdd] Write Protect is off
sd 7:0:0:0: [sdd] Mode Sense: 00 00 00 00
sd 7:0:0:0: [sdd] Assuming drive cache: write through
sd 7:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 7:0:0:0: [sdd] Write Protect is off
sd 7:0:0:0: [sdd] Mode Sense: 00 00 00 00
sd 7:0:0:0: [sdd] Assuming drive cache: write through
sdd: sdd1
sd 7:0:0:0: [sdd] Attached SCSI disk
Adding 19631388k swap on /dev/sdb6. Priority:-1 extents:1
across:19631388k
EXT3 FS on sdb1, internal journal
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169: eth0: link up
r8169: eth0: link up
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 5400+
processors (1 cpu cores) (version 2.20.00)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
NFSD: starting 90-second grace period
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 5
eth0: no IPv6 routers present
hda-intel: Invalid position buffer, using LPIB read method instead
Any help you can provide would be appreciated. I would love to Debian up
and running properly.
Thanks for all of your efforts.
Tim Patterson
tspatterson@xmission.com
Reply to: