Bug#477833: "PCI: Cannot allocate resource region" errors
Package: linux-image-2.6.24-1-amd64
Version: 2.6.24-5
Severity: normal
File: kernel
*** Please type your report below this line ***
After upgrade to 2.6.24 (from 2.6.22) lines including
PCI: Cannot allocate resource region :
PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
I googled abit and found that people reprted this about the acer 5100
family laptops.
I have Acer 5102 .
I tested the next hardware and it works ok :
Card reader
DVD writer.
touchpad
PCMCIA
I can't check the m5602 integrated webcam (no working driver yet).
-- Package-specific info:
** Version:
Linux version 2.6.24-1-amd64 (Debian 2.6.24-5) (waldi@debian.org) (gcc
version 4.1.3 20080308 (prerelease) (Debian 4.1.2-21)) #1 SMP Thu Mar
27 16:52:38 UTC 2008
** Command line:
root=/dev/sda7 ro quiet
** Not tainted
** Kernel log:
ide1: ATIIXP Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
hda: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input4
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SLPB]
Linux video capture interface: v2.00
ACPI: AC Adapter [ACAD] (on-line)
input: Video Bus as /class/input/input6
/home/jabka/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c:
usb_m5602_init - WebCam driver startup
/home/jabka/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c:
BisonCam webcam found.
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
input: Video Bus as /class/input/input7
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
/home/jabka/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c:
Probing for an ov9650 sensor
/home/jabka/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c:
m5602_probe - m5602 WebCam driver is now controlling video device 0
usbcore: registered new interface driver m5602
/home/jabka/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c:
0.1.0:M5602 Webcam Driver
Yenta: CardBus bridge found at 0000:06:04.0 [1025:009f]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:04.0, mfunc 0x90501212, devctl 0x44
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ACPI: Battery Slot [BAT1] (battery present)
input: PC Speaker as /class/input/input8
Yenta: ISA IRQ mask 0x0cf8, PCI irq 20
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
pcmcia: parent PCI bridge Memory window: 0xb0200000 - 0xb02fffff
b43-phy0: Broadcom 4318 WLAN found
phy0: Selected rate control algorithm 'simple'
sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1)
ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 23 (level, low) -> IRQ 23
mmc0: SDHCI at 0xb0202800 irq 23 PIO
sdhci: SDHCI controller found at 0000:06:04.4 [1524:0551] (rev 1)
PCI: Enabling device 0000:06:04.4 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:04.4[B] -> GSI 23 (level, low) -> IRQ 23
mmc1: SDHCI at 0xb0202100 irq 23 PIO
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
udev: renamed network interface wlan0 to eth1
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps:
0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad as /class/input/input9
Adding 1951856k swap on /dev/sda6. Priority:-1 extents:1 across:1951856k
EXT3 FS on sda7, internal journal
loop: module loaded
eth0: link down
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
input: b43-phy0 as /class/input/input10
Registered led device: b43-phy0:tx
Registered led device: b43-phy0:rx
Registered led device: b43-phy0:radio
hda-intel: Invalid position buffer, using LPIB read method instead.
eth1: Initial auth_alg=0
eth1: authenticate with AP 00:11:6b:22:7f:76
eth1: RX authentication from 00:11:6b:22:7f:76 (alg=0 transaction=2
status=0)
eth1: authenticated
eth1: associate with AP 00:11:6b:22:7f:76
eth1: RX AssocResp from 00:11:6b:22:7f:76 (capab=0x421 status=0 aid=1)
eth1: associated
eth1: switched to short barker preamble (BSSID=00:11:6b:22:7f:76)
** Loaded modules:
Module Size Used by
rfkill_input 9600 0
rfcomm 46240 2
l2cap 29568 9 rfcomm
bluetooth 65956 4 rfcomm,l2cap
ppdev 13832 0
parport_pc 42408 0
lp 17476 0
parport 44812 3 ppdev,parport_pc,lp
loop 22788 0
joydev 17536 0
arc4 6528 2
ecb 8192 2
blkcipher 11780 1 ecb
b43 120616 0
rfkill 12816 3 rfkill_input,b43
mac80211 132236 1 b43
snd_hda_intel 362024 0
serio_raw 11908 0
cfg80211 19856 1 mac80211
pcspkr 7808 0
snd_pcm_oss 46624 0
snd_mixer_oss 21376 1 snd_pcm_oss
led_class 10120 1 b43
k8temp 10496 0
psmouse 45724 0
input_polldev 9872 1 b43
sdhci 23172 0
yenta_socket 31756 1
rsrc_nonstatic 16128 1 yenta_socket
mmc_core 58760 1 sdhci
snd_pcm 89352 2 snd_hda_intel,snd_pcm_oss
battery 19976 0
snd_timer 28552 1 snd_pcm
m5602 40328 0
video 25620 0
output 8704 1 video
container 9856 0
snd 65896 5
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
ac 11400 0
videodev 32256 1 m5602
v4l2_common 24320 1 videodev
soundcore 13216 1 snd
v4l1_compat 16388 1 videodev
shpchp 38428 0
snd_page_alloc 15248 2 snd_hda_intel,snd_pcm
button 13984 0
pci_hotplug 35504 1 shpchp
i2c_piix4 13708 0
i2c_core 29824 1 i2c_piix4
evdev 17024 9
ext3 139024 1
jbd 55976 1 ext3
mbcache 13952 1 ext3
ide_cd 44704 0
cdrom 39464 1 ide_cd
sd_mod 33536 3
atiixp 9488 0 [permanent]
8139cp 28672 0
generic 9732 0 [permanent]
ide_core 144920 3 ide_cd,atiixp,generic
sata_sil 17288 2
8139too 33024 0
mii 10240 2 8139cp,8139too
ssb 39428 1 b43
pcmcia 45720 2 b43,ssb
pcmcia_core 46500 4 b43,yenta_socket,rsrc_nonstatic,pcmcia
firmware_class 15104 2 b43,pcmcia
ata_generic 13060 0
ehci_hcd 39692 0
ohci_hcd 28164 0
libata 162736 2 sata_sil,ata_generic
scsi_mod 170296 2 sd_mod,libata
thermal 22688 0
processor 45032 1 thermal
fan 9864 0
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS480 Host Bridge
[1002:5950] (rev 10)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge
[1002:5a3f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: b0100000-b01fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:04.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge
[1002:5a36] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge
[1002:5a37] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:12.0 IDE interface [0101]: ATI Technologies Inc IXP SB400 Serial
ATA Controller [1002:4379] (rev 80) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: ATI Technologies Inc IXP SB400 Serial ATA Controller
[1002:4379]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 8440 [size=8]
Region 1: I/O ports at 8434 [size=4]
Region 2: I/O ports at 8438 [size=8]
Region 3: I/O ports at 8430 [size=4]
Region 4: I/O ports at 8400 [size=16]
Region 5: Memory at b0004000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 50000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil
Kernel modules: ata_generic, sata_sil, generic
00:13.0 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host
Controller [1002:4374] (rev 80) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b0005000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host
Controller [1002:4375] (rev 80) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b0006000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB2
Host Controller [1002:4373] (rev 80) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b0007000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc IXP SB400 SMBus Controller
[1002:4372] (rev 83)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 8410 [size=16]
Region 1: Memory at 50080000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 IDE interface [0101]: ATI Technologies Inc IXP SB400 IDE
Controller [1002:4376] (rev 80) (prog-if 82 [Master PriP])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 8420 [size=16]
Capabilities: <access denied>
Kernel driver in use: ATIIXP_IDE
Kernel modules: ata_generic, generic, atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc IXP SB4x0 High
Definition Audio Controller [1002:437b] (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc IXP SB400 PCI-ISA
Bridge [1002:4377] (rev 80)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc IXP SB400 PCI-PCI
Bridge [1002:4371] (rev 80) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=06, subordinate=08, sec-latency=64
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: b0200000-b02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS485
[Radeon Xpress 1100 IGP] [1002:5975] (prog-if 00 [VGA controller])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at b0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at b0120000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeonfb
06:01.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at b0202000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
06:02.0 Network controller [0280]: Broadcom Corporation BCM4318
[AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: AMBIT Microsystem Corp. TravelMate 2410 [1468:0312]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 22
Region 0: Memory at b0200000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
06:04.0 CardBus bridge [0607]: ENE Technology Inc CB-712/4 Cardbus
Controller [1524:1412] (rev 10)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at b0203000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=07, sec-latency=176
Memory window 0: 54000000-57fff000 (prefetchable)
Memory window 1: 58000000-5bfff000
I/O window 0: 0000a400-0000a4ff
I/O window 1: 0000a800-0000a8ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
06:04.1 FLASH memory [0501]: ENE Technology Inc ENE PCI Memory Stick
Card Reader Controller [1524:0530] (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at b0202400 (32-bit, non-prefetchable) [size=128]
Capabilities: <access denied>
06:04.2 SD Host controller [0805]: ENE Technology Inc ENE PCI Secure
Digital Card Reader Controller [1524:0550] (rev 01) (prog-if 01)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 18000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 23
Region 0: Memory at b0202800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci
Kernel modules: sdhci
06:04.3 FLASH memory [0501]: ENE Technology Inc FLASH memory: ENE
Technology Inc: [1524:0520] (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at b0202c00 (32-bit, non-prefetchable) [size=128]
Capabilities: <access denied>
06:04.4 FLASH memory [0501]: ENE Technology Inc SD/MMC Card Reader
Controller [1524:0551] (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:009f]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 23
Region 0: Memory at b0202100 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci
Kernel modules: sdhci
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.24-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.24-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.20 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.92 tools for generating an
initramfs
ii module-init-tools 3.4-1 tools for managing Linux
kernel mo
linux-image-2.6.24-1-amd64 recommends no packages.
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-1-amd64/preinst/abort-overwrite-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-dir-initrd-link-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/preinst/failed-to-move-modules-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/bootloader-test-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/preinst/lilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/create-kimage-link-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/postinst/depmod-error-initrd-2.6.24-1-amd64:
false
linux-image-2.6.24-1-amd64/postinst/old-system-map-link-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.24-1-amd64/preinst/overwriting-modules-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/postinst/bootloader-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/preinst/abort-install-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.24-1-amd64/preinst/bootloader-initrd-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/prerm/would-invalidate-boot-loader-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/preinst/initrd-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/prerm/removing-running-kernel-2.6.24-1-amd64:
true
linux-image-2.6.24-1-amd64/preinst/elilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-2.6.24-1-amd64: false
Reply to: