Bug#475319: linux-image-2.6.24-1-amd64: Hangs on boot after "ACPI: Battery slot [BAT1] (battery present)"
I have this same error. However, I *have* gotten this kernel to boot
after a hard reset if I am lucky.
I am attaching my dmesg.
Hardware:
Dual Opteron 244's
MSI K8T Master2-FAR motherboard
VIA K8T8000 Chipset
1 SATA drive
1 IDE drive
$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South]
00:0b.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705 Gigabit Ethernet (rev 03)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200] (rev 01)
01:00.1 Display controller: ATI Technologies Inc Unknown device 5942 (rev 01)
Thanks for looking at this bug. Thanks to the Kernel Team for putting
these kernel images out!
-s
Initializing cgroup subsys cpuset
Linux version 2.6.24-1-amd64 (Debian 2.6.24-5) (waldi@debian.org) (gcc version 4.1.3 20080308 (prerelease) (Debian 4.1.2-21)) #1 SMP Thu Mar 27 16:52:38 UTC 2008
Command line: BOOT_IMAGE=(hd0,1)/vmlinuz-2.6.24-1-amd64 root=/dev/sda3 ro pci=routeirq
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 524000) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000F6980, 0014 (r0 VIAK8 )
ACPI: RSDT 7FEE3000, 002C (r1 VIAK8 AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 7FEE3040, 0074 (r1 VIAK8 AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 7FEE30C0, 4A4C (r1 VIAK8 AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 7FEE0000, 0040
ACPI: APIC 7FEE7B40, 0068 (r1 VIAK8 AWRDACPI 42302E31 AWRD 0)
Scanning NUMA topology in Northbridge 24
CPU has 1 num_cores
Number of nodes 2
Node 0 MemBase 0000000000000000 Limit 000000007fee0000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 524000) 1 entries of 3200 used
Skipping disabled node 1
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000007fee0000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 157
0: 256 -> 524000
On node 0 totalpages: 523901
DMA zone: 56 pages used for memmap
DMA zone: 1066 pages reserved
DMA zone: 2875 pages, LIFO batch:0
DMA32 zone: 7108 pages used for memmap
DMA32 zone: 512796 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7ff00000:7ed00000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 34400 bytes of per cpu data
Built 1 zonelists in Node order, mobility grouping on. Total pages: 515671
Policy zone: DMA32
Kernel command line: BOOT_IMAGE=(hd0,1)/vmlinuz-2.6.24-1-amd64 root=/dev/sda3 ro pci=routeirq
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1804.089 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
CPU 0: aperture @ f0000000 size 64 MB
CPU 1: aperture @ f0000000 size 64 MB
Memory: 2056796k/2096000k available (2143k kernel code, 38808k reserved, 1003k data, 316k init)
Calibrating delay using timer specific routine.. 3612.55 BogoMIPS (lpj=7225105)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12528421
Detected 12.528 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3608.21 BogoMIPS (lpj=7216423)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
AMD Opteron(tm) Processor 244 stepping 08
Brought up 2 CPUs
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:04: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0a: Plug and Play ACPI device, IDs PNP0401 (active)
pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
NET: Registered protocol family 8
NET: Registered protocol family 20
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf0000000
ACPI: RTC can wake from S4
pnp: the driver 'system' has been registered
system 00:00: iomem range 0xf0000-0xf3fff could not be reserved
system 00:00: iomem range 0xf4000-0xf7fff could not be reserved
system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x7fee0000-0x7fefffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff has been reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x7fedffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
system 00:00: driver attached
system 00:02: ioport range 0x4000-0x407f has been reserved
system 00:02: ioport range 0x5000-0x500f has been reserved
system 00:02: driver attached
system 00:03: ioport range 0xb78-0xb7b has been reserved
system 00:03: ioport range 0xf78-0xf7b has been reserved
system 00:03: ioport range 0xa78-0xa7b has been reserved
system 00:03: ioport range 0xe78-0xe7b has been reserved
system 00:03: ioport range 0xbbc-0xbbf has been reserved
system 00:03: ioport range 0xfbc-0xfbf has been reserved
system 00:03: ioport range 0x4d0-0x4d1 has been reserved
system 00:03: driver attached
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: f4000000-f5ffffff
PREFETCH window: e0000000-efffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5681k freed
audit: initializing netlink socket (disabled)
audit(1207931807.864:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 00:08: driver attached
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial 00:09: driver attached
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
input: Macintosh mouse button emulation as /class/input/input0
pnp: the driver 'i8042 kbd' has been registered
i8042 kbd 00:0b: driver attached
pnp: the driver 'i8042 aux' has been registered
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 316k freed
input: AT Translated Set 2 keyboard as /class/input/input1
ACPI: Fan [FAN] (on)
ACPI: processor limited to max C-state 1
ACPI: Thermal Zone [THRM] (40 C)
SCSI subsystem initialized
libata version 3.00 loaded.
sata_via 0000:00:0f.0: version 2.3
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 11
scsi0 : sata_via
scsi1 : sata_via
ata1: SATA max UDMA/133 cmd 0xa000 ctl 0xa400 bmdma 0xb000 irq 20
ata2: SATA max UDMA/133 cmd 0xa800 ctl 0xac00 bmdma 0xb008 irq 20
USB Universal Host Controller Interface driver v3.0
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: ST3500320AS, SD15, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA ST3500320AS SD15 PQ: 0 ANSI: 5
tg3.c:v3.86 (November 9, 2007)
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Disallowing DAC for device 0000:00:0b.0
eth0: Tigon3 [partno(BCM95705A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:11:09:7a:79:1f
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000bc00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<6>udev: renamed network interface eth0 to eth_tg3
sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.4: irq 21, io mem 0xf6010000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hdb: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
hda: Maxtor 94098H6, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
usb 3-2: new low speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 3-1.2: new low speed USB device using uhci_hcd and address 4
hdc: LS-120 CSMO 05 UHD Floppy, ATAPI FLOPPY drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO2
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO2
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdc: No disk in drive
hdc: 123264kB, 963/8/32 CHS, 533 kBps, 512 sector size, 720 rpm
usb 3-1.2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
hiddev96hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 1000 FW:600.3.D USB FW:8.1] on usb-0000:00:10.2-2
input: Kensington Kensington USB/PS2 Wheel Mouse as /class/input/input2
input,hidraw1: USB HID v1.10 Mouse [Kensington Kensington USB/PS2 Wheel Mouse] on usb-0000:00:10.2-1.2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
hda: UDMA/100 mode selected
hda: cache flushes not supported
input: PC Speaker as /class/input/input3
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
input: Power Button (FF) as /class/input/input4
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
pnp: the driver 'parport_pc' has been registered
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ACPI: Power Button (CM) [PWRB]
parport_pc 00:0a: driver attached
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
devpts: called with bogus options
hda: UDMA/100 mode selected
hda: cache flushes not supported
EXT3 FS on sda3, internal journal
w83627hf: Found W83627THF chip at 0x290
kjournald starting. Commit interval 60 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 60 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdc: No disk in drive
tg3: eth_tg3: Link is up at 1000 Mbps, full duplex.
tg3: eth_tg3: Flow control is on for TX and on for RX.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth_tg3: no IPv6 routers present
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
hdc: No disk in drive
cdrom: This disc doesn't have any tracks I recognize!
pktcdvd: writer pktcdvd0 mapped to hdb
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.28.0 20060524 on minor 0
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Device is in legacy mode, falling back to 2.x
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
Reply to: