Bug#465775: b43: ethX is renamed to wlan0_rename when b43 wireless module loads
Package: linux-image-2.6.24-1-686
Version: 2.6.24-4
Severity: important
File: b43
*** Please type your report below this line ***
when system loads, udev: renamed network interface wmaster0 to eth2
but later on, when i am logged into KDE. i notice i have another wireless
interface : "wlan0_rename" and eth2 is empty.
wlan0_rename works fine but where is it coming from ?
(i want my eth2 back ;-)
laptop:~# ifconfig
eth1 Link encap:Ethernet HWaddr 00:08:02:ba:ac:f9
inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:701 errors:0 dropped:0 overruns:0 frame:0
TX packets:472 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:964853 (942.2 KiB) TX bytes:34913 (34.0 KiB)
eth2 Link encap:UNSPEC HWaddr
00-12-17-B6-8D-E5-77-6C-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:300 errors:0 dropped:0 overruns:0 frame:0
TX packets:300 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:22593 (22.0 KiB) TX bytes:22593 (22.0 KiB)
wlan0_rename Link encap:Ethernet HWaddr 00:12:17:b6:8d:e5
inet addr:192.168.1.106 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::212:17ff:feb6:8de5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:323 errors:0 dropped:0 overruns:0 frame:0
TX packets:222 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:197199 (192.5 KiB) TX bytes:45976 (44.8 KiB)
cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
iface lo inet loopback
address 127.0.0.1
netmask 255.0.0.0
auto lo
# The primary network interface
allow-hotplug eth1
iface eth0 inet dhcp
iface eth1 inet dhcp
#auto eth1
iface eth2 inet dhcp
##post-up cp -f /etc/resolv.conf.netvision /etc/resolv.conf
wireless-channel 11
wireless-essid kaval
wireless-ap auto
wireless-mode managed
auto eth2
# added to support new b43 module (2.6.24-X)
iface wlan0_rename inet dhcp
wireless-essid kaval
##post-up cp -f /etc/resolv.conf.netvision /etc/resolv.conf
wireless-channel 11
wireless-mode managed
wireless-ap auto
auto wlan0_rename
-- Package-specific info:
** Version:
Linux version 2.6.24-1-686 (Debian 2.6.24-4) (waldi@debian.org) (gcc version
4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Mon Feb 11 14:37:45 UTC
2008
** Command line:
root=/dev/hda1 ro
** Tainted: G (128)
** Kernel log:
b43-phy1: Broadcom 4306 WLAN found
phy1: Selected rate control algorithm 'simple'
udev: renamed network interface wmaster0 to eth2
input: b43-phy1 as /class/input/input18
Registered led device: b43-phy1:tx
Registered led device: b43-phy1:rx
Registered led device: b43-phy1:radio
wlan0_rename: Initial auth_alg=0
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: RX AssocResp from 00:18:39:bc:52:67 (capab=0x1 status=0 aid=1)
wlan0_rename: associated
wlan0_rename: Initial auth_alg=0
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: RX ReassocResp from 00:18:39:bc:52:67 (capab=0x1 status=0 aid=1)
wlan0_rename: associated
wlan0_rename: Initial auth_alg=0
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: RX ReassocResp from 00:18:39:bc:52:67 (capab=0x1 status=0 aid=1)
wlan0_rename: associated
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
wlan0_rename: no IPv6 routers present
wlan0_rename: RX deauthentication from 00:18:39:bc:52:67 (reason=7)
wlan0_rename: deauthenticated
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: RX ReassocResp from 00:18:39:bc:52:67 (capab=0x1 status=0 aid=1)
wlan0_rename: associated
wlan0_rename: RX deauthentication from 00:18:39:bc:52:67 (reason=7)
wlan0_rename: deauthenticated
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: RX ReassocResp from 00:18:39:bc:52:67 (capab=0x1 status=0 aid=1)
wlan0_rename: associated
pccard: card ejected from slot 0
b43-phy1 ERROR: DMA RX reset timed out
b43-phy1 ERROR: DMA TX reset timed out
b43-phy1 ERROR: DMA TX reset timed out
b43-phy1 ERROR: DMA TX reset timed out
b43-phy1 ERROR: DMA TX reset timed out
b43-phy1 ERROR: DMA TX reset timed out
b43-phy1 ERROR: DMA TX reset timed out
ssb: Failed to switch to core 0
ACPI: PCI interrupt for device 0000:03:00.0 disabled
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [C0B8] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:03:00.0 to 64
b43-phy2: Broadcom 4306 WLAN found
phy2: Selected rate control algorithm 'simple'
ssb: Sonics Silicon Backplane found on PCI device 0000:03:00.0
udev: renamed network interface wmaster0 to eth2
input: b43-phy2 as /class/input/input19
Registered led device: b43-phy2:tx
Registered led device: b43-phy2:rx
Registered led device: b43-phy2:radio
ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
wlan0_rename: Initial auth_alg=0
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: Initial auth_alg=0
wlan0_rename: authenticate with AP 00:18:39:bc:52:67
wlan0_rename: association frame received from 00:18:39:bc:52:67, but not in
associate state - ignored
wlan0_rename: RX authentication from 00:18:39:bc:52:67 (alg=0 transaction=2
status=0)
wlan0_rename: authenticated
wlan0_rename: associate with AP 00:18:39:bc:52:67
wlan0_rename: RX AssocResp from 00:18:39:bc:52:67 (capab=0x1 status=0 aid=1)
wlan0_rename: associated
ADDRCONF(NETDEV_CHANGE): wlan0_rename: link becomes ready
wlan0_rename: no IPv6 routers present
** Loaded modules:
Module Size Used by
ipv6 240772 8
b43 105664 0
radeon 112096 2
drm 74132 3 radeon
binfmt_misc 11240 1
cpufreq_userspace 4260 1
ppdev 8804 0
lp 11076 0
rfkill_input 4544 0
fuse 45204 1
dm_snapshot 16964 0
dm_mirror 21600 0
dm_mod 55812 2 dm_snapshot,dm_mirror
cpufreq_ondemand 8492 0
cpufreq_powersave 1856 0
p4_clockmod 5412 0
speedstep_lib 5348 1 p4_clockmod
freq_table 4512 2 cpufreq_ondemand,p4_clockmod
firewire_sbp2 14252 0
loop 16804 0
arc4 2016 2
ecb 3552 2
blkcipher 6724 1 ecb
rfkill 7312 13 b43,rfkill_input
mac80211 114380 1 b43
cfg80211 13480 1 mac80211
led_class 5156 1 b43
input_polldev 5000 1 b43
ssb 30628 1 b43
joydev 11360 0
irtty_sir 8096 0
sir_dev 15460 1 irtty_sir
pcmcia 37036 2 b43,ssb
firmware_class 9312 2 b43,pcmcia
snd_intel8x0 32028 1
snd_ac97_codec 92932 1 snd_intel8x0
ac97_bus 2176 1 snd_ac97_codec
snd_pcm_oss 38272 0
snd_mixer_oss 15296 1 snd_pcm_oss
snd_pcm 71780 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
irda 174236 2 irtty_sir,sir_dev
parport_pc 33668 1
parport 34280 3 ppdev,lp,parport_pc
snd_seq_dummy 3780 0
crc_ccitt 2176 1 irda
rtc 13052 0
pcspkr 3200 0
psmouse 36464 0
serio_raw 6660 0
snd_seq_oss 29472 0
snd_seq_midi 8160 0
snd_rawmidi 22624 1 snd_seq_midi
snd_seq_midi_event 6976 2 snd_seq_oss,snd_seq_midi
snd_seq 46544 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 21092 2 snd_pcm,snd_seq
snd_seq_device 7820 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
yenta_socket 24844 2
rsrc_nonstatic 11872 1 yenta_socket
pcmcia_core 36884 4 b43,pcmcia,yenta_socket,rsrc_nonstatic
snd 48612 12
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 7552 1 snd
snd_page_alloc 10056 2 snd_intel8x0,snd_pcm
container 4864 0
battery 13572 0
ac 6116 0
button 8432 0
intel_agp 23412 1
iTCO_wdt 11268 0
shpchp 31028 0
pci_hotplug 27712 1 shpchp
agpgart 31688 2 drm,intel_agp
evdev 11104 18
ext3 122920 1
jbd 43732 1 ext3
mbcache 8288 1 ext3
ide_cd 36224 0
cdrom 32512 1 ide_cd
ide_disk 15648 3
generic 4388 0 [permanent]
usbhid 28096 0
hid 34272 1 usbhid
piix 7492 0 [permanent]
ide_core 108292 4 ide_cd,ide_disk,generic,piix
floppy 54628 0
ata_generic 7428 0
libata 144464 1 ata_generic
scsi_mod 141196 2 firewire_sbp2,libata
ehci_hcd 32524 0
ohci_hcd 21988 0
e100 33836 0
mii 5312 1 e100
usbcore 132940 4 usbhid,ehci_hcd,ohci_hcd
firewire_ohci 17760 0
firewire_core 39232 2 firewire_sbp2,firewire_ohci
crc_itu_t 2176 1 firewire_core
thermal 16028 0
processor 36520 2 thermal
fan 4772 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82845 845 [Brookdale] Chipset
Host Bridge [8086:1a30] (rev 04)
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at 60000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] Vendor Specific Information <?>
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+
AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82845 845 [Brookdale] Chipset AGP
Bridge [8086:1a31] (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 7c000000-7c0fffff
Prefetchable memory behind bridge: 70000000-7bffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 42) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 00002000-00002fff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801CAM ISA Bridge (LPC)
[8086:248c] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801CAM IDE U100 Controller
[8086:248a] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 4440 [size=16]
Region 5: Memory at 7c100000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801CA/CAM
AC'97 Audio Controller [8086:2485] (rev 02)
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 4000 [size=256]
Region 1: I/O ports at 4400 [size=64]
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility
M7 LW [Radeon Mobility 7500] [1002:4c57] (prog-if 00 [VGA controller])
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 70000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at 7c000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 78000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW-
AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: radeonfb
02:05.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device [1179:ff01]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 66 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 7c100800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at 7c104000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
02:06.0 CardBus bridge [0607]: Texas Instruments PCI1410 PC card Cardbus
Controller [104c:ac50] (rev 02)
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 7c101000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 80000000-83fff000 (prefetchable)
Memory window 1: 84000000-87fff000
I/O window 0: 00002400-000024ff
I/O window 1: 00002800-000028ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:08.0 Ethernet controller [0200]: Intel Corporation 82801CAM (ICH3) PRO/100
VE (LOM) Ethernet Controller [8086:1031] (rev 42)
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 7c102000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
Kernel modules: e100, eepro100
02:0e.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41)
(prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 7c103000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
02:0e.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41)
(prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 7c108000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
02:0e.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 02)
(prog-if 20 [EHCI])
Subsystem: Compaq Computer Corporation Unknown device [0e11:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at 7c100400 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
03:00.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g
Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Linksys WPC54G [1737:4320]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 84000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.24-1-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.24-1-686 depends on:
ii debconf [debconf-2.0] 1.5.19 Debian configuration management
sy
ii initramfs-tools [linux-initr 0.91d tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel
mo
Versions of packages linux-image-2.6.24-1-686 recommends:
ii libc6-i686 2.7-5 GNU C Library: Shared libraries
[i
-- debconf information:
linux-image-2.6.24-1-686/preinst/overwriting-modules-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/bootloader-error-2.6.24-1-686:
linux-image-2.6.24-1-686/postinst/create-kimage-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/prerm/would-invalidate-boot-loader-2.6.24-1-686:
true
linux-image-2.6.24-1-686/preinst/initrd-2.6.24-1-686:
linux-image-2.6.24-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.24-1-686/preinst/abort-install-2.6.24-1-686:
linux-image-2.6.24-1-686/prerm/removing-running-kernel-2.6.24-1-686: true
linux-image-2.6.24-1-686/preinst/abort-overwrite-2.6.24-1-686:
linux-image-2.6.24-1-686/postinst/bootloader-test-error-2.6.24-1-686:
linux-image-2.6.24-1-686/preinst/lilo-initrd-2.6.24-1-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-1-686/postinst/old-system-map-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/preinst/failed-to-move-modules-2.6.24-1-686:
linux-image-2.6.24-1-686/postinst/depmod-error-initrd-2.6.24-1-686: false
linux-image-2.6.24-1-686/preinst/bootloader-initrd-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/old-initrd-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/old-dir-initrd-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/depmod-error-2.6.24-1-686: false
linux-image-2.6.24-1-686/preinst/elilo-initrd-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/kimage-is-a-directory:
Reply to: