Bug#462484: linux-image-2.6.23-1-686: usb mouse broken on X20 (intermittent)
Package: linux-image-2.6.23-1-686
Version: 2.6.23-2
Severity: normal
On my Thinkpad X20, frequently after booting my usb mouse responds in a
very sluggish and jumpy manner, making it basically unuseable. At the
same time, the stick mouse (which I hate using) works normally.
This has been going on for a while, at least the last couple of kernels.
Sometimes I can restore function by unplugging and replugging the USB
mouse, but not reliably, and even then, after replugging it will not
respond at all for some great length of time until some unknown event
causes it to come to life.
-- Package-specific info:
** Version:
Linux version 2.6.23-1-686 (Debian 2.6.23-2) (maks@debian.org) (gcc version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #1 SMP Fri Dec 21 13:57:07 UTC 2007
** cmdline:
root=/dev/hda2 ro resume=/dev/hda4
** Not tainted
** Kernel log:
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ACPI: PCI Interrupt 0000:00:08.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
firewire_ohci: Added fw-ohci device 0000:00:08.2, OHCI version 1.0
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usb 1-1: new full speed USB device using uhci_hcd and address 2
hda: IC25N030ATCS04-0, ATA DISK drive
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Clocksource tsc unstable (delta = -1880422397 ns)
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
SCSI subsystem initialized
libata version 2.21 loaded.
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=62016/15/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4
hda3: <netbsd: hda5 hda6bad subpartition - ignored
bad subpartition - ignored
>
usb 1-1: configuration #1 chosen from 1 choice
Attempting manual resume
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
usb 1-1.2: new low speed USB device using uhci_hcd and address 3
usb 1-1.2: configuration #1 chosen from 1 choice
input: PC Speaker as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Yenta: CardBus bridge found at 0000:00:08.0 [1014:0184]
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000410
Yenta: CardBus bridge found at 0000:00:08.1 [1014:0184]
Linux agpgart interface v0.102
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
Real Time Clock Driver v1.12ac
pccard: PCMCIA card inserted into slot 0
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
piix4_smbus: probe of 0000:00:07.3 failed with error -1
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input2
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SLPB]
pnp: Device 00:0c activated.
parport_pc 00:0c: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
input: Video Bus as /class/input/input6
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: AC Adapter [AC] (on-line)
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
ACPI: Battery Slot [BAT0] (battery absent)
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia0.0
usbcore: registered new interface driver hiddev
input: USB Mouse as /class/input/input7
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:07.2-1.2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
eth1: Atmel at76c50x. Version 0.98. MAC 00:30:bd:d0:16:d0
Adding 322208k swap on /dev/hda4. Priority:-1 extents:1 across:322208k
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
fuse init (API version 7.8)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (5120 buckets, 20480 max)
eth1: no IPv6 routers present
uhci_hcd 0000:00:07.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
scim-launcher[3307]: segfault at b737c232 eip b737c232 esp bf8936cc error 4
ADDRCONF(NETDEV_UP): eth1: link is not ready
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
eth1: no IPv6 routers present
** Loaded modules:
Module Size Used by
nf_conntrack_ftp 8960 0
nf_conntrack_irc 6808 0
ipt_REJECT 4544 4
ipt_LOG 5984 7
xt_limit 2688 7
xt_state 2496 35
xt_tcpudp 3168 28
nf_conntrack_ipv4 17448 35
nf_conntrack 62056 4 nf_conntrack_ftp,nf_conntrack_irc,xt_state,nf_conntrack_ipv4
nfnetlink 5816 2 nf_conntrack_ipv4,nf_conntrack
iptable_filter 3008 1
ip_tables 13220 1 iptable_filter
x_tables 14308 6 ipt_REJECT,ipt_LOG,xt_limit,xt_state,xt_tcpudp,ip_tables
ipv6 242788 19
ext3 121544 0
jbd 55368 1 ext3
vfat 12256 0
fat 48540 1 vfat
fuse 41876 1
dm_crypt 12840 0
dm_snapshot 16932 0
dm_mirror 21632 0
dm_mod 52640 3 dm_crypt,dm_snapshot,dm_mirror
ide_cd 36384 0
cdrom 32608 1 ide_cd
atmel_cs 7232 1
atmel 32740 1 atmel_cs
usbhid 27232 0
hid 26944 1 usbhid
tsdev 8160 0
battery 12296 0
ac 5636 0
pcmcia 37388 1 atmel_cs
firmware_class 9472 2 atmel,pcmcia
video 18608 0
output 3840 1 video
parport_pc 34020 0
parport 34088 1 parport_pc
button 8336 0
psmouse 36368 0
i2c_piix4 8524 0
intel_agp 23348 1
rtc 12984 0
serio_raw 6724 0
i2c_core 23264 1 i2c_piix4
agpgart 31624 1 intel_agp
yenta_socket 24908 4
rsrc_nonstatic 11904 1 yenta_socket
pcmcia_core 37076 4 atmel_cs,pcmcia,yenta_socket,rsrc_nonstatic
shpchp 31028 0
pci_hotplug 28128 1 shpchp
pcspkr 3264 0
evdev 9472 5
ext2 60104 1
mbcache 8320 2 ext3,ext2
ide_disk 16544 3
ata_generic 7588 0
libata 113488 1 ata_generic
scsi_mod 136684 1 libata
piix 8932 0 [permanent]
firewire_ohci 16640 0
generic 4804 0 [permanent]
floppy 54820 0
uhci_hcd 23056 0
firewire_core 39072 1 firewire_ohci
crc_itu_t 2208 1 firewire_core
3c59x 41416 0
mii 5344 1 3c59x
ide_core 112484 4 ide_cd,ide_disk,piix,generic
usbcore 130568 3 usbhid,uhci_hcd
thermal 15580 0
processor 34696 1 thermal
fan 5092 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f4100000-f5ffffff
Prefetchable memory behind bridge: 30000000-300fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:07.0 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 1800 [size=16]
00:07.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
00:07.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:08.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c478 [1180:0478] (rev a0)
Subsystem: IBM ThinkPad A30p (2653-64G) [1014:0184]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:08.1 CardBus bridge [0607]: Ricoh Co Ltd RL5c478 [1180:0478] (rev a0)
Subsystem: IBM ThinkPad A30p (2653-64G) [1014:0184]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 28000000-2bfff000 (prefetchable)
Memory window 1: 2c000000-2ffff000
I/O window 0: 00002800-000028ff
I/O window 1: 00002c00-00002cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:08.2 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C522 IEEE 1394 Controller [1180:0522] (prog-if 10 [OHCI])
Subsystem: IBM ThinkPad A30p (2653-64G) [1014:01cf]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4011000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
00:0a.0 Ethernet controller [0200]: 3Com Corporation 3c556B CardBus [Tornado] [10b7:6056] (rev 20)
Subsystem: 3Com Corporation Unknown device [10b7:6356]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at f4011c00 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at f4011800 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 30100000 [disabled] [size=128K]
Capabilities: <access denied>
00:0a.1 Communication controller [0780]: 3Com Corporation Mini PCI 56k Winmodem [10b7:1007] (rev 20)
Subsystem: 3Com Corporation Unknown device [10b7:6159]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2400 [size=256]
Region 1: Memory at f4012400 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at f4012000 (32-bit, non-prefetchable) [size=128]
Capabilities: <access denied>
00:0b.0 Multimedia audio controller [0401]: Cirrus Logic Crystal CS4281 PCI Audio [1013:6005] (rev 01)
Subsystem: IBM Unknown device [1014:0183]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4010000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Rage Mobility P/M AGP 2x [1002:4c4d] (rev 64) (prog-if 00 [VGA])
Subsystem: IBM Unknown device [1014:0182]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.23-1-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.23-1-686 depends on:
ii initramfs-tools [linux-initr 0.91d tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.23-1-686 recommends no packages.
-- debconf information:
linux-image-2.6.23-1-686/prerm/removing-running-kernel-2.6.23-1-686: true
linux-image-2.6.23-1-686/postinst/old-system-map-link-2.6.23-1-686: true
linux-image-2.6.23-1-686/preinst/abort-overwrite-2.6.23-1-686:
linux-image-2.6.23-1-686/postinst/create-kimage-link-2.6.23-1-686: true
linux-image-2.6.23-1-686/preinst/failed-to-move-modules-2.6.23-1-686:
linux-image-2.6.23-1-686/preinst/lilo-initrd-2.6.23-1-686: true
linux-image-2.6.23-1-686/postinst/depmod-error-initrd-2.6.23-1-686: false
linux-image-2.6.23-1-686/preinst/elilo-initrd-2.6.23-1-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.23-1-686/preinst/overwriting-modules-2.6.23-1-686: true
linux-image-2.6.23-1-686/preinst/already-running-this-2.6.23-1-686:
linux-image-2.6.23-1-686/preinst/initrd-2.6.23-1-686:
linux-image-2.6.23-1-686/preinst/abort-install-2.6.23-1-686:
linux-image-2.6.23-1-686/postinst/depmod-error-2.6.23-1-686: false
linux-image-2.6.23-1-686/postinst/old-dir-initrd-link-2.6.23-1-686: true
linux-image-2.6.23-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.23-1-686/preinst/bootloader-initrd-2.6.23-1-686: true
linux-image-2.6.23-1-686/prerm/would-invalidate-boot-loader-2.6.23-1-686: true
linux-image-2.6.23-1-686/postinst/old-initrd-link-2.6.23-1-686: true
linux-image-2.6.23-1-686/postinst/bootloader-error-2.6.23-1-686:
linux-image-2.6.23-1-686/postinst/bootloader-test-error-2.6.23-1-686:
linux-image-2.6.23-1-686/postinst/kimage-is-a-directory:
Reply to: