--- Begin Message ---
Package: linux-image-2.6.23-1-amd64
Version: 2.6.23-2
Severity: important
the media changer device doesn't work. on startup an error -EEXIST for a ch kobject gets triggered.
linux-image-2.6.21-2-amd64 (2.6.21-6) works
every kernel later (even upstream) doesn't
the working snippet ...
ch0: type #1 (mt): 0x1+1 [medium transport]
ch0: type #2 (st): 0x1000+81 [storage]
ch0: type #3 (ie): 0x10+6 [import/export]
ch0: type #4 (dt): 0x100+2 [data transfer]
ch0: dt 0x100: ID/LUN unknown
ch0: dt 0x101: ID/LUN unknown
ch0: INITIALIZE ELEMENT STATUS, may take some time ...
ch0: ... finished
ch 2:0:0:1: Attached scsi changer ch0
sd 1:0:0:0: Attached scsi generic sg0 type 0
st 0:0:0:0: Attached scsi generic sg1 type 1
sd 3:0:0:0: Attached scsi generic sg2 type 0
st 2:0:0:0: Attached scsi generic sg3 type 1
ch 2:0:0:1: Attached scsi generic sg4 type 8
the failing snippet ...
scsi 2:0:0:1: Medium Changer ADIC Scalar i500 400G PQ: 0 ANSI: 3
kobject_add failed for 2:0:0:1 with -EEXIST, don't try to register things with the same name in the same directory.
Call Trace:
[<ffffffff802febc0>] kobject_shadow_add+0x16e/0x1a2
[<ffffffff80365450>] device_add+0x99/0x614
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
[<ffffffff8805955a>] :scsi_mod:scsi_sysfs_add_sdev+0x35/0x218
[<ffffffff88057640>] :scsi_mod:scsi_probe_and_add_lun+0x953/0xa95
[<ffffffff88055f7f>] :scsi_mod:scsi_execute_req+0x82/0xde
[<ffffffff88058041>] :scsi_mod:__scsi_scan_target+0x407/0x5c3
[<ffffffff880587d0>] :scsi_mod:scsi_scan_target+0x96/0xbb
[<ffffffff880b49ed>] :scsi_transport_fc:fc_scsi_scan_rport+0x59/0x7a
[<ffffffff880b4994>] :scsi_transport_fc:fc_scsi_scan_rport+0x0/0x7a
[<ffffffff80243481>] run_workqueue+0x7f/0x10b
[<ffffffff80243db8>] worker_thread+0x0/0xe4
[<ffffffff80243e92>] worker_thread+0xda/0xe4
[<ffffffff80246b96>] autoremove_wake_function+0x0/0x2e
[<ffffffff80246a79>] kthread+0x47/0x76
[<ffffffff8020cc08>] child_rip+0xa/0x12
[<ffffffff80246a32>] kthread+0x0/0x76
[<ffffffff8020cbfe>] child_rip+0x0/0x12
error 1
st 2:0:0:0: Unexpected response from lun 1 while scanning, scan aborted
sd 3:0:0:0: [sdb] 1874933760 512-byte hardware sectors (959966 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
sdb: sdb4 < sdb5 >
sd 3:0:0:0: [sdb] Attached SCSI disk
SCSI Media Changer driver v0.25
ch 2:0:0:1: rejecting I/O to dead device
ch0: type #1 (mt): 0x0+0 [medium transport]
ch0: type #2 (st): 0x0+0 [storage]
ch0: type #3 (ie): 0x0+0 [import/export]
ch0: type #4 (dt): 0x0+0 [data transfer]
ch0: INITIALIZE ELEMENT STATUS, may take some time ...
ch 2:0:0:1: rejecting I/O to dead device
ch0: ... finished
ch 2:0:0:1: Attached scsi changer ch0
st 1:0:0:0: Attached scsi generic sg0 type 1
sd 0:0:0:0: Attached scsi generic sg1 type 0
st 2:0:0:0: Attached scsi generic sg2 type 1
ch 2:0:0:1: Attached scsi generic sg3 type 8
sd 3:0:0:0: Attached scsi generic sg4 type 0
the device gets listed but has the state set to deleted.
thanks for your help!
thomas
-- Package-specific info:
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (800, 'testing'), (700, 'stable'), (500, 'testing-proposed-updates'), (500, 'proposed-updates'), (70, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.21-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=de_AT.UTF-8, LC_CTYPE=de_AT.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.23-1-amd64 depends on:
ii e2fsprogs 1.40.3-1 ext2 file system utilities and lib
ii initramfs-tools [linux-initr 0.91d tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.23-1-amd64 recommends no packages.
-- debconf information excluded
Linux version 2.6.21-2-amd64 (Debian 2.6.21-6) (waldi@debian.org) (gcc version 4.1.3 20070629 (prerelease) (Debian 4.1.2-13)) #1 SMP Tue Jul 10 21:39:38 UTC 2007
Command line: root=/dev/sda2 ro
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000c2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bff10000 (usable)
BIOS-e820: 00000000bff10000 - 00000000bff1c000 (ACPI data)
BIOS-e820: 00000000bff1c000 - 00000000bff80000 (ACPI NVS)
BIOS-e820: 00000000bff80000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000240000000 (usable)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 786192) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 2359296) 2 entries of 3200 used
end_pfn_map = 2359296
DMI present.
ACPI: RSDP 000F6F50, 0014 (r0 PTLTD )
ACPI: RSDT BFF17D77, 0038 (r1 PTLTD RSDT 6040000 LTP 0)
ACPI: FACP BFF1BA8E, 0074 (r1 NVIDIA CK8S 6040000 PTL_ F4240)
ACPI: DSDT BFF17DAF, 3CDF (r1 NVIDIA CK8 6040000 MSFT 100000E)
ACPI: FACS BFF1CFC0, 0040
ACPI: SSDT BFF1BB02, 03F4 (r1 PTLTD POWERNOW 6040000 LTP 1)
ACPI: SPCR BFF1BEF6, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1)
ACPI: APIC BFF1BF46, 0092 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: BOOT BFF1BFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
Scanning NUMA topology in Northbridge 24
Number of nodes 2
Node 0 using interleaving mode 1/0
No NUMA configuration found
Faking a node at 0000000000000000-0000000240000000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 786192) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 2359296) 2 entries of 3200 used
Bootmem setup node 0 0000000000000000-0000000240000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 2359296
early_node_map[3] active PFN ranges
0: 0 -> 157
0: 256 -> 786192
0: 1048576 -> 2359296
On node 0 totalpages: 2096813
DMA zone: 56 pages used for memmap
DMA zone: 984 pages reserved
DMA zone: 2957 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 767816 pages, LIFO batch:31
Normal zone: 17920 pages used for memmap
Normal zone: 1292800 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xda400000] gsi_base[24])
IOAPIC[1]: apic_id 5, address 0xda400000, GSI 24-27
ACPI: IOAPIC (id[0x06] address[0xda401000] gsi_base[28])
IOAPIC[2]: apic_id 6, address 0xda401000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009d000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000c2000
Nosave address range: 00000000000c2000 - 0000000000100000
Nosave address range: 00000000bff10000 - 00000000bff1c000
Nosave address range: 00000000bff1c000 - 00000000bff80000
Nosave address range: 00000000bff80000 - 00000000c0000000
Nosave address range: 00000000c0000000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000fec00000
Nosave address range: 00000000fec00000 - 00000000fee00000
Nosave address range: 00000000fee00000 - 00000000fee01000
Nosave address range: 00000000fee01000 - 00000000fff80000
Nosave address range: 00000000fff80000 - 0000000100000000
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PERCPU: Allocating 37504 bytes of per cpu data
Built 1 zonelists. Total pages: 2063573
Kernel command line: root=/dev/sda2 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 2411.116 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Checking aperture...
CPU 0: aperture @ c0000000 size 256 MB
CPU 1: aperture @ c0000000 size 256 MB
Memory: 8235196k/9437184k available (1976k kernel code, 152056k reserved, 931k data, 296k init)
Calibrating delay using timer specific routine.. 4825.14 BogoMIPS (lpj=9650283)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12557907
Detected 12.557 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4822.60 BogoMIPS (lpj=9645200)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Dual Core AMD Opteron(tm) Processor 280 stepping 02
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 4822.65 BogoMIPS (lpj=9645300)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/2 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Dual Core AMD Opteron(tm) Processor 280 stepping 02
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 4822.55 BogoMIPS (lpj=9645109)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/3 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Dual Core AMD Opteron(tm) Processor 280 stepping 02
Brought up 4 CPUs
migration_cost=458
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:06.0
PCI: Firmware left 0000:01:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Root Bridge [PCI2] (0000:18)
PCI: Probing PCI hardware (bus 18)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0F13
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0A03
pnp: PnP ACPI: found 14 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 4 of device 0000:00:01.1
PCI: Cannot allocate resource region 5 of device 0000:00:01.1
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ c0000000 size 262144 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 256MB of IOMMU area in the AGP aperture
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:00' and the driver 'system'
pnp: 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
pnp: 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:00: iomem range 0xfefff000-0xfeffffff has been reserved
pnp: match found with the PnP device '00:02' and the driver 'system'
pnp: 00:02: ioport range 0x8000-0x807f has been reserved
pnp: 00:02: ioport range 0x8080-0x80ff has been reserved
pnp: 00:02: ioport range 0x8400-0x847f has been reserved
pnp: 00:02: ioport range 0x8480-0x84ff has been reserved
pnp: 00:02: ioport range 0x8800-0x887f has been reserved
pnp: 00:02: ioport range 0x8880-0x88ff has been reserved
pnp: 00:02: ioport range 0x5000-0x503f has been reserved
pnp: 00:02: ioport range 0x5040-0x507f has been reserved
pnp: match found with the PnP device '00:03' and the driver 'system'
PCI: Bridge: 0000:00:09.0
IO window: 2000-2fff
MEM window: d8100000-d9ffffff
PREFETCH window: d0000000-d00fffff
PCI: Bridge: 0000:00:0d.0
IO window: 3000-3fff
MEM window: da000000-da0fffff
PREFETCH window: d0100000-d01fffff
PCI: Bridge: 0000:00:0e.0
IO window: 4000-4fff
MEM window: da100000-da1fffff
PREFETCH window: d0200000-d02fffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Bridge: 0000:18:0a.0
IO window: 5000-5fff
MEM window: da500000-da5fffff
PREFETCH window: dc000000-dfffffff
Time: acpi_pm clocksource has been installed.
PCI: Bridge: 0000:18:0b.0
IO window: disabled.
MEM window: da600000-da6fffff
PREFETCH window: d0300000-d03fffff
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6407k freed
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1199787212.768:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:18:0a.0 subordinate bus.
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:18:0b.0 subordinate bus.
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'serial'
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: match found with the PnP device '00:0b' and the driver 'serial'
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:09' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:08' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 296k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 23 (level, high) -> IRQ 23
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 23, io mem 0xd8001000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
SCSI subsystem initialized
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Floppy drive(s): fd0 is 1.44M
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
QLogic Fibre Channel HBA Driver
FDC 0 is a post-1991 82077
tg3.c:v3.75.2 (June 5, 2007)
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0x1400-0x1407, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1408-0x140f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK4] -> GSI 19 (level, high) -> IRQ 19
ACPI: PCI Interrupt 0000:1a:09.0[A] -> <6>qla2xxx 0000:02:00.0: Found an ISP2432, irq 19, iobase 0xffffc2000001a000
GSI 28 (level, low) -> IRQ 28
qla2xxx 0000:02:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:02:00.0 to 64
qla2xxx 0000:02:00.0: Configure NVRAM parameters...
qla2xxx 0000:02:00.0: Verifying loaded RISC code...
eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:33:6e:5c
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:1a:09.1[B] -> GSI 29 (level, low) -> IRQ 29
eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:33:6e:5d
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:19:02.0[A] -> GSI 26 (level, low) -> IRQ 26
udev: renamed network interface eth1 to giga1
udev: renamed network interface eth0 to giga2
qla2xxx 0000:02:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:02:00.0: Allocated (1413 KB) for firmware dump...
3w-9xxx: scsi1: AEN: WARNING (0x04:0x0008): Unclean shutdown detected:unit=0.
scsi0 : qla2xxx
qla2xxx 0000:02:00.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k5
QLogic QLE2460 - PCI-Express to 4Gb FC, Single Channel
ISP2432: PCIe (2.5Gb/s x4) @ 0000:02:00.0 hdma+, host#=0, fw=4.03.00 [IP]
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNK3] -> GSI 18 (level, high) -> IRQ 18
qla2xxx 0000:03:00.0: Found an ISP2432, irq 18, iobase 0xffffc2000001e000
qla2xxx 0000:03:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:03:00.0 to 64
qla2xxx 0000:03:00.0: Configure NVRAM parameters...
qla2xxx 0000:03:00.0: Verifying loaded RISC code...
scsi1 : 3ware 9000 Storage Controller
3w-9xxx: scsi1: Found a 3ware 9000 Storage Controller at 0xda500000, IRQ: 26.
qla2xxx 0000:02:00.0: LIP reset occured (f7f7).
qla2xxx 0000:03:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:03:00.0: Allocated (1413 KB) for firmware dump...
qla2xxx 0000:02:00.0: LIP occured (f7f7).
qla2xxx 0000:02:00.0: LOOP UP detected (4 Gbps).
Probing IDE interface ide1...
scsi2 : qla2xxx
qla2xxx 0000:03:00.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k5
QLogic QLE2460 - PCI-Express to 4Gb FC, Single Channel
ISP2432: PCIe (2.5Gb/s x4) @ 0000:03:00.0 hdma+, host#=2, fw=4.03.00 [IP]
3w-9xxx: scsi1: Firmware FE9X 3.08.00.016, BIOS BE9X 3.08.00.004, Ports: 4.
ACPI: PCI Interrupt 0000:19:03.0[A] -> GSI 27 (level, low) -> IRQ 27
scsi 1:0:0:0: Direct-Access AMCC 9550SX-4LP DISK 3.08 PQ: 0 ANSI: 5
3w-9xxx: scsi3: AEN: WARNING (0x04:0x0008): Unclean shutdown detected:unit=0.
qla2xxx 0000:03:00.0: LIP reset occured (f7f7).
qla2xxx 0000:03:00.0: LIP occured (f7f7).
qla2xxx 0000:03:00.0: LOOP UP detected (4 Gbps).
scsi3 : 3ware 9000 Storage Controller
3w-9xxx: scsi3: Found a 3ware 9000 Storage Controller at 0xda501000, IRQ: 27.
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 22, io mem 0xd8000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
scsi 0:0:0:0: Sequential-Access IBM ULTRIUM-TD3 6B20 PQ: 0 ANSI: 3
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNK3] -> GSI 18 (level, high) -> IRQ 18
e100: eth0: e100_probe: addr 0xd8101000, irq 18, MAC addr 00:E0:81:33:6F:28
3w-9xxx: scsi3: Firmware FE9X 3.08.00.016, BIOS BE9X 3.08.00.004, Ports: 4.
scsi 3:0:0:0: Direct-Access AMCC 9550SX-4LP DISK 3.08 PQ: 0 ANSI: 5
libata version 2.20 loaded.
scsi 2:0:0:0: Sequential-Access IBM ULTRIUM-TD3 6B20 PQ: 0 ANSI: 3
scsi 2:0:0:1: Medium Changer ADIC Scalar i500 400G PQ: 0 ANSI: 3
SCSI device sda: 2343684096 512-byte hdwr sectors (1199966 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
udev: renamed network interface eth0 to mega1
SCSI device sda: write cache: enabled, read cache: disabled, doesn't support DPO or FUA
SCSI device sda: 2343684096 512-byte hdwr sectors (1199966 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: write cache: enabled, read cache: disabled, doesn't support DPO or FUA
sda:<6>st: Version 20070203, fixed bufsize 32768, s/g segs 256
SCSI Media Changer driver v0.25
sda1 sda2 sda3
sd 1:0:0:0: Attached scsi disk sda
st 0:0:0:0: Attached scsi tape st0
st 0:0:0:0: st0: try direct i/o: yes (alignment 512 B)
SCSI device sdb: 1874933760 512-byte hdwr sectors (959966 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
SCSI device sdb: write cache: enabled, read cache: disabled, doesn't support DPO or FUA
SCSI device sdb: 1874933760 512-byte hdwr sectors (959966 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
SCSI device sdb: write cache: enabled, read cache: disabled, doesn't support DPO or FUA
sdb: sdb4 < sdb5 >
sd 3:0:0:0: Attached scsi disk sdb
st 2:0:0:0: Attached scsi tape st1
st 2:0:0:0: st1: try direct i/o: yes (alignment 512 B)
ch0: type #1 (mt): 0x1+1 [medium transport]
ch0: type #2 (st): 0x1000+81 [storage]
ch0: type #3 (ie): 0x10+6 [import/export]
ch0: type #4 (dt): 0x100+2 [data transfer]
ch0: dt 0x100: ID/LUN unknown
ch0: dt 0x101: ID/LUN unknown
ch0: INITIALIZE ELEMENT STATUS, may take some time ...
ch0: ... finished
ch 2:0:0:1: Attached scsi changer ch0
sd 1:0:0:0: Attached scsi generic sg0 type 0
st 0:0:0:0: Attached scsi generic sg1 type 1
sd 3:0:0:0: Attached scsi generic sg2 type 0
st 2:0:0:0: Attached scsi generic sg3 type 1
ch 2:0:0:1: Attached scsi generic sg4 type 8
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Attempting manual resume
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sda2
Ending clean XFS mount for filesystem: sda2
st0: Block limits 1 - 16777215 bytes.
st1: Block limits 1 - 16777215 bytes.
input: PC Speaker as /class/input/input1
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1040
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Filesystem "dm-3": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-3
Ending clean XFS mount for filesystem: dm-3
Filesystem "dm-2": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-2
Ending clean XFS mount for filesystem: dm-2
Filesystem "dm-4": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-4
Ending clean XFS mount for filesystem: dm-4
Filesystem "dm-0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-0
Ending clean XFS mount for filesystem: dm-0
Filesystem "dm-1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-1
Ending clean XFS mount for filesystem: dm-1
Filesystem "dm-5": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-5
Ending clean XFS mount for filesystem: dm-5
Filesystem "dm-8": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-8
Ending clean XFS mount for filesystem: dm-8
Filesystem "dm-7": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-7
Ending clean XFS mount for filesystem: dm-7
Adding 2097144k swap on /dev/mapper/system_vg-swap1_lv. Priority:-1 extents:1 across:2097144k
PM: Writing back config space on device 0000:1a:09.0 at offset b (was 164814e4, writing 164414e4)
PM: Writing back config space on device 0000:1a:09.0 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device 0000:1a:09.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:1a:09.0 at offset 1 (was 2b00000, writing 2b00106)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): giga2: link is not ready
PM: Writing back config space on device 0000:1a:09.1 at offset b (was 164814e4, writing 164414e4)
PM: Writing back config space on device 0000:1a:09.1 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device 0000:1a:09.1 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:1a:09.1 at offset 1 (was 2b00000, writing 2b00106)
ADDRCONF(NETDEV_UP): giga1: link is not ready
Linux version 2.6.23-1-amd64 (Debian 2.6.23-2) (maks@debian.org) (gcc version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #1 SMP Fri Dec 21 12:00:17 UTC 2007
Command line: root=/dev/sda2 ro scsi_mod.scan=sync
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000c2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bff10000 (usable)
BIOS-e820: 00000000bff10000 - 00000000bff1c000 (ACPI data)
BIOS-e820: 00000000bff1c000 - 00000000bff80000 (ACPI NVS)
BIOS-e820: 00000000bff80000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000240000000 (usable)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 786192) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 2359296) 2 entries of 3200 used
end_pfn_map = 2359296
DMI present.
ACPI: RSDP 000F6F50, 0014 (r0 PTLTD )
ACPI: RSDT BFF17D77, 0038 (r1 PTLTD RSDT 6040000 LTP 0)
ACPI: FACP BFF1BA8E, 0074 (r1 NVIDIA CK8S 6040000 PTL_ F4240)
ACPI: DSDT BFF17DAF, 3CDF (r1 NVIDIA CK8 6040000 MSFT 100000E)
ACPI: FACS BFF1CFC0, 0040
ACPI: SSDT BFF1BB02, 03F4 (r1 PTLTD POWERNOW 6040000 LTP 1)
ACPI: SPCR BFF1BEF6, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1)
ACPI: APIC BFF1BF46, 0092 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: BOOT BFF1BFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
Scanning NUMA topology in Northbridge 24
CPU has 2 num_cores
Number of nodes 2
Node 0 using interleaving mode 1/0
No NUMA configuration found
Faking a node at 0000000000000000-0000000240000000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 786192) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 2359296) 2 entries of 3200 used
Bootmem setup node 0 0000000000000000-0000000240000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 2359296
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0 -> 157
0: 256 -> 786192
0: 1048576 -> 2359296
On node 0 totalpages: 2096813
DMA zone: 56 pages used for memmap
DMA zone: 1041 pages reserved
DMA zone: 2900 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 767816 pages, LIFO batch:31
Normal zone: 17920 pages used for memmap
Normal zone: 1292800 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xda400000] gsi_base[24])
IOAPIC[1]: apic_id 5, address 0xda400000, GSI 24-27
ACPI: IOAPIC (id[0x06] address[0xda401000] gsi_base[28])
IOAPIC[2]: apic_id 6, address 0xda401000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009d000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000c2000
swsusp: Registered nosave memory region: 00000000000c2000 - 0000000000100000
swsusp: Registered nosave memory region: 00000000bff10000 - 00000000bff1c000
swsusp: Registered nosave memory region: 00000000bff1c000 - 00000000bff80000
swsusp: Registered nosave memory region: 00000000bff80000 - 00000000c0000000
swsusp: Registered nosave memory region: 00000000c0000000 - 00000000e0000000
swsusp: Registered nosave memory region: 00000000e0000000 - 00000000f0000000
swsusp: Registered nosave memory region: 00000000f0000000 - 00000000fec00000
swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fee00000
swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fee01000
swsusp: Registered nosave memory region: 00000000fee01000 - 00000000fff80000
swsusp: Registered nosave memory region: 00000000fff80000 - 0000000100000000
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PERCPU: Allocating 35176 bytes of per cpu data
Built 1 zonelists in Zone order. Total pages: 2063516
Policy zone: Normal
Kernel command line: root=/dev/sda2 ro scsi_mod.scan=sync
Unknown boot option `scsi_mod.scan=sync': ignoring
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2411.121 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
CPU 0: aperture @ c0000000 size 256 MB
CPU 1: aperture @ c0000000 size 256 MB
Memory: 8247284k/9437184k available (2060k kernel code, 139968k reserved, 969k data, 304k init)
Calibrating delay using timer specific routine.. 4825.17 BogoMIPS (lpj=9650351)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12557933
Detected 12.557 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4822.57 BogoMIPS (lpj=9645146)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Dual Core AMD Opteron(tm) Processor 280 stepping 02
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 4822.57 BogoMIPS (lpj=9645153)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/2 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Dual Core AMD Opteron(tm) Processor 280 stepping 02
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 4822.49 BogoMIPS (lpj=9644983)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/3 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Dual Core AMD Opteron(tm) Processor 280 stepping 02
Brought up 4 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Root Bridge [PCI2] (0000:18)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0F13
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0A03
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 4 of device 0000:00:01.1
PCI: Cannot allocate resource region 5 of device 0000:00:01.1
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ c0000000 size 262144 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 256MB of IOMMU area in the AGP aperture
ACPI: RTC can wake from S4
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:00' and the driver 'system'
pnp: 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
pnp: 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:00: iomem range 0xfefff000-0xfeffffff has been reserved
pnp: match found with the PnP device '00:02' and the driver 'system'
pnp: 00:02: ioport range 0x8000-0x807f has been reserved
pnp: 00:02: ioport range 0x8080-0x80ff has been reserved
pnp: 00:02: ioport range 0x8400-0x847f has been reserved
pnp: 00:02: ioport range 0x8480-0x84ff has been reserved
pnp: 00:02: ioport range 0x8800-0x887f has been reserved
pnp: 00:02: ioport range 0x8880-0x88ff has been reserved
pnp: 00:02: ioport range 0x5000-0x503f has been reserved
pnp: 00:02: ioport range 0x5040-0x507f has been reserved
pnp: match found with the PnP device '00:03' and the driver 'system'
PCI: Bridge: 0000:00:09.0
IO window: 2000-2fff
MEM window: d8100000-d9ffffff
PREFETCH window: d0000000-d00fffff
PCI: Bridge: 0000:00:0d.0
IO window: 3000-3fff
MEM window: da000000-da0fffff
PREFETCH window: d0100000-d01fffff
PCI: Bridge: 0000:00:0e.0
IO window: 4000-4fff
MEM window: da100000-da1fffff
PREFETCH window: d0200000-d02fffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Bridge: 0000:18:0a.0
IO window: 5000-5fff
MEM window: da500000-da5fffff
PREFETCH window: dc000000-dfffffff
PCI: Bridge: 0000:18:0b.0
IO window: disabled.
MEM window: da600000-da6fffff
PREFETCH window: d0300000-d03fffff
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 1048576 (order: 12, 25165824 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 1048576 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6377k freed
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1199786432.052:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
Boot video device is 0000:01:06.0
PCI: Firmware left 0000:01:08.0 e100 interrupts enabled, disabling
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:18:0a.0 subordinate bus.
AMD8131 rev 12 detected, disabling PCI-X MMRBC
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:18:0b.0 subordinate bus.
AMD8131 rev 12 detected, disabling PCI-X MMRBC
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'serial'
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: match found with the PnP device '00:0b' and the driver 'serial'
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
input: Macintosh mouse button emulation as /class/input/input0
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:09' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:08' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 304k freed
input: AT Translated Set 2 keyboard as /class/input/input1
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 23 (level, high) -> IRQ 23
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 23, io mem 0xd8001000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
SCSI subsystem initialized
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
QLogic Fibre Channel HBA Driver
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 22, io mem 0xd8000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
ACPI: PCI Interrupt 0000:19:02.0[A] -> GSI 26 (level, low) -> IRQ 26
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNK3] -> GSI 19 (level, high) -> IRQ 19
e100: eth0: e100_probe: addr 0xd8101000, irq 19, MAC addr 00:E0:81:33:6F:28
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK4] -> GSI 18 (level, high) -> IRQ 18
qla2xxx 0000:02:00.0: Found an ISP2432, irq 18, iobase 0xffffc2000273a000
qla2xxx 0000:02:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:02:00.0 to 64
qla2xxx 0000:02:00.0: Configure NVRAM parameters...
qla2xxx 0000:02:00.0: Verifying loaded RISC code...
3w-9xxx: scsi0: AEN: WARNING (0x04:0x0008): Unclean shutdown detected:unit=0.
scsi0 : 3ware 9000 Storage Controller
3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xda500000, IRQ: 26.
qla2xxx 0000:02:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:02:00.0: Allocated (1413 KB) for firmware dump...
scsi1 : qla2xxx
qla2xxx 0000:02:00.0:
QLogic Fibre Channel HBA Driver: 8.02.00-k3
QLogic QLE2460 - PCI-Express to 4Gb FC, Single Channel
ISP2432: PCIe (2.5Gb/s x4) @ 0000:02:00.0 hdma+, host#=1, fw=4.03.00 [IP]
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNK3] -> GSI 19 (level, high) -> IRQ 19
qla2xxx 0000:03:00.0: Found an ISP2432, irq 19, iobase 0xffffc2000273c000
qla2xxx 0000:03:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:03:00.0 to 64
qla2xxx 0000:03:00.0: Configure NVRAM parameters...
qla2xxx 0000:03:00.0: Verifying loaded RISC code...
qla2xxx 0000:02:00.0: LIP reset occured (f7f7).
qla2xxx 0000:02:00.0: LIP occured (f7f7).
qla2xxx 0000:02:00.0: LOOP UP detected (4 Gbps).
qla2xxx 0000:03:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:03:00.0: Allocated (1413 KB) for firmware dump...
3w-9xxx: scsi0: Firmware FE9X 3.08.00.016, BIOS BE9X 3.08.00.004, Ports: 4.
ACPI: PCI Interrupt 0000:19:03.0[A] -> GSI 27 (level, low) -> IRQ 27
scsi 0:0:0:0: Direct-Access AMCC 9550SX-4LP DISK 3.08 PQ: 0 ANSI: 5
scsi2 : qla2xxx
qla2xxx 0000:03:00.0:
QLogic Fibre Channel HBA Driver: 8.02.00-k3
QLogic QLE2460 - PCI-Express to 4Gb FC, Single Channel
ISP2432: PCIe (2.5Gb/s x4) @ 0000:03:00.0 hdma+, host#=2, fw=4.03.00 [IP]
3w-9xxx: scsi3: AEN: WARNING (0x04:0x0008): Unclean shutdown detected:unit=0.
scsi3 : 3ware 9000 Storage Controller
3w-9xxx: scsi3: Found a 3ware 9000 Storage Controller at 0xda501000, IRQ: 27.
qla2xxx 0000:03:00.0: LIP reset occured (f7f7).
qla2xxx 0000:03:00.0: LIP occured (f7f7).
qla2xxx 0000:03:00.0: LOOP UP detected (4 Gbps).
3w-9xxx: scsi3: Firmware FE9X 3.08.00.016, BIOS BE9X 3.08.00.004, Ports: 4.
tg3.c:v3.81.1 (October 18, 2007)
ACPI: PCI Interrupt 0000:1a:09.0[A] -> GSI 28 (level, low) -> IRQ 28
scsi 3:0:0:0: Direct-Access AMCC 9550SX-4LP DISK 3.08 PQ: 0 ANSI: 5
net mega1: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0 to mega1
eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:33:6e:5c
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:1a:09.1[B] -> GSI 29 (level, low) -> IRQ 29
scsi 1:0:0:0: Sequential-Access IBM ULTRIUM-TD3 6B20 PQ: 0 ANSI: 3
eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:33:6e:5d
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
sd 0:0:0:0: [sda] 2343684096 512-byte hardware sectors (1199966 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
sd 0:0:0:0: [sda] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 2343684096 512-byte hardware sectors (1199966 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
net giga1: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth1 to giga1
sd 0:0:0:0: [sda] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
sda:<3>net giga2: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0 to giga2
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0x1400-0x1407, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1408-0x140f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
st: Version 20070203, fixed bufsize 32768, s/g segs 256
st 1:0:0:0: Attached scsi tape st0
st 1:0:0:0: st0: try direct i/o: yes (alignment 512 B)
scsi 2:0:0:0: Sequential-Access IBM ULTRIUM-TD3 6B20 PQ: 0 ANSI: 3
st 2:0:0:0: Attached scsi tape st1
st 2:0:0:0: st1: try direct i/o: yes (alignment 512 B)
sd 3:0:0:0: [sdb] 1874933760 512-byte hardware sectors (959966 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
scsi 2:0:0:1: Medium Changer ADIC Scalar i500 400G PQ: 0 ANSI: 3
kobject_add failed for 2:0:0:1 with -EEXIST, don't try to register things with the same name in the same directory.
Call Trace:
[<ffffffff802febc0>] kobject_shadow_add+0x16e/0x1a2
[<ffffffff80365450>] device_add+0x99/0x614
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
[<ffffffff8805955a>] :scsi_mod:scsi_sysfs_add_sdev+0x35/0x218
[<ffffffff88057640>] :scsi_mod:scsi_probe_and_add_lun+0x953/0xa95
[<ffffffff88055f7f>] :scsi_mod:scsi_execute_req+0x82/0xde
[<ffffffff88058041>] :scsi_mod:__scsi_scan_target+0x407/0x5c3
[<ffffffff880587d0>] :scsi_mod:scsi_scan_target+0x96/0xbb
[<ffffffff880b49ed>] :scsi_transport_fc:fc_scsi_scan_rport+0x59/0x7a
[<ffffffff880b4994>] :scsi_transport_fc:fc_scsi_scan_rport+0x0/0x7a
[<ffffffff80243481>] run_workqueue+0x7f/0x10b
[<ffffffff80243db8>] worker_thread+0x0/0xe4
[<ffffffff80243e92>] worker_thread+0xda/0xe4
[<ffffffff80246b96>] autoremove_wake_function+0x0/0x2e
[<ffffffff80246a79>] kthread+0x47/0x76
[<ffffffff8020cc08>] child_rip+0xa/0x12
[<ffffffff80246a32>] kthread+0x0/0x76
[<ffffffff8020cbfe>] child_rip+0x0/0x12
error 1
st 2:0:0:0: Unexpected response from lun 1 while scanning, scan aborted
sd 3:0:0:0: [sdb] 1874933760 512-byte hardware sectors (959966 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
sdb: sdb4 < sdb5 >
sd 3:0:0:0: [sdb] Attached SCSI disk
SCSI Media Changer driver v0.25
ch 2:0:0:1: rejecting I/O to dead device
ch0: type #1 (mt): 0x0+0 [medium transport]
ch0: type #2 (st): 0x0+0 [storage]
ch0: type #3 (ie): 0x0+0 [import/export]
ch0: type #4 (dt): 0x0+0 [data transfer]
ch0: INITIALIZE ELEMENT STATUS, may take some time ...
ch 2:0:0:1: rejecting I/O to dead device
ch0: ... finished
ch 2:0:0:1: Attached scsi changer ch0
st 1:0:0:0: Attached scsi generic sg0 type 1
sd 0:0:0:0: Attached scsi generic sg1 type 0
st 2:0:0:0: Attached scsi generic sg2 type 1
ch 2:0:0:1: Attached scsi generic sg3 type 8
sd 3:0:0:0: Attached scsi generic sg4 type 0
Probing IDE interface ide1...
libata version 2.21 loaded.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Attempting manual resume
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sda2
Ending clean XFS mount for filesystem: sda2
st1: Block limits 1 - 16777215 bytes.
st0: Block limits 1 - 16777215 bytes.
input: PC Speaker as /class/input/input2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1000
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1040
input: ImPS/2 Generic Wheel Mouse as /class/input/input5
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Filesystem "dm-3": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-3
Ending clean XFS mount for filesystem: dm-3
Filesystem "dm-2": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-2
Ending clean XFS mount for filesystem: dm-2
Filesystem "dm-4": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-4
Ending clean XFS mount for filesystem: dm-4
Filesystem "dm-0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-0
Ending clean XFS mount for filesystem: dm-0
Filesystem "dm-1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-1
Ending clean XFS mount for filesystem: dm-1
Filesystem "dm-5": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-5
Ending clean XFS mount for filesystem: dm-5
Filesystem "dm-8": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-8
Ending clean XFS mount for filesystem: dm-8
Filesystem "dm-7": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-7
Ending clean XFS mount for filesystem: dm-7
Adding 2097144k swap on /dev/mapper/system_vg-swap1_lv. Priority:-1 extents:1 across:2097144k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): giga2: link is not ready
ADDRCONF(NETDEV_UP): giga1: link is not ready
--- End Message ---
--- Begin Message ---
- To: 459732-close@bugs.debian.org
- Subject: Bug#459732: fixed in linux-2.6 2.6.24~rc8-1~experimental.1
- From: Bastian Blank <waldi@debian.org>
- Date: Thu, 24 Jan 2008 21:58:27 +0000
- Message-id: <E1JIA5b-0000xf-83@ries.debian.org>
Source: linux-2.6
Source-Version: 2.6.24~rc8-1~experimental.1
We believe that the bug you reported is fixed in the latest version of
linux-2.6, which is due to be installed in the Debian FTP archive:
linux-2.6_2.6.24~rc8-1~experimental.1.diff.gz
to pool/main/l/linux-2.6/linux-2.6_2.6.24~rc8-1~experimental.1.diff.gz
linux-2.6_2.6.24~rc8-1~experimental.1.dsc
to pool/main/l/linux-2.6/linux-2.6_2.6.24~rc8-1~experimental.1.dsc
linux-2.6_2.6.24~rc8.orig.tar.gz
to pool/main/l/linux-2.6/linux-2.6_2.6.24~rc8.orig.tar.gz
linux-doc-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
to pool/main/l/linux-2.6/linux-doc-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
linux-headers-2.6.24-rc8-all-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-all-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-headers-2.6.24-rc8-all_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-all_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-headers-2.6.24-rc8-common_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-common_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-headers-2.6.24-rc8-powerpc-miboot_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-powerpc-miboot_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-headers-2.6.24-rc8-powerpc-smp_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-powerpc-smp_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-headers-2.6.24-rc8-powerpc64_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-powerpc64_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-headers-2.6.24-rc8-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-headers-2.6.24-rc8-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-image-2.6.24-rc8-powerpc-miboot_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-image-2.6.24-rc8-powerpc-miboot_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-image-2.6.24-rc8-powerpc-smp_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-image-2.6.24-rc8-powerpc-smp_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-image-2.6.24-rc8-powerpc64_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-image-2.6.24-rc8-powerpc64_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-image-2.6.24-rc8-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-image-2.6.24-rc8-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-libc-dev_2.6.24~rc8-1~experimental.1_powerpc.deb
to pool/main/l/linux-2.6/linux-libc-dev_2.6.24~rc8-1~experimental.1_powerpc.deb
linux-manual-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
to pool/main/l/linux-2.6/linux-manual-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
linux-patch-debian-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
to pool/main/l/linux-2.6/linux-patch-debian-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
linux-source-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
to pool/main/l/linux-2.6/linux-source-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
linux-support-2.6.24-rc8_2.6.24~rc8-1~experimental.1_all.deb
to pool/main/l/linux-2.6/linux-support-2.6.24-rc8_2.6.24~rc8-1~experimental.1_all.deb
linux-tree-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
to pool/main/l/linux-2.6/linux-tree-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
A summary of the changes between this version and the previous one is
attached.
Thank you for reporting the bug, which will now be closed. If you
have further comments please address them to 459732@bugs.debian.org,
and the maintainer will reopen the bug report if appropriate.
Debian distribution maintenance software
pp.
Bastian Blank <waldi@debian.org> (supplier of updated linux-2.6 package)
(This message was generated automatically at their request; if you
believe that there is a problem with it please contact the archive
administrators by mailing ftpmaster@debian.org)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Format: 1.7
Date: Fri, 18 Jan 2008 12:23:26 +0100
Source: linux-2.6
Binary: linux-headers-2.6.24-rc8-all-m68k linux-headers-2.6.24-rc8-xen-686 linux-patch-debian-2.6.24 linux-headers-2.6.24-rc8-s390x linux-image-2.6.24-rc8-powerpc-smp linux-headers-2.6.24-rc8-parisc linux-support-2.6.24-rc8 linux-image-2.6.24-rc8-parisc64 linux-headers-2.6.24-rc8-sparc64 linux-image-2.6.24-rc8-r5k-ip32 linux-headers-2.6.24-rc8-mckinley linux-image-2.6.24-rc8-footbridge linux-headers-2.6.24-rc8-all-powerpc linux-headers-2.6.24-rc8-ixp4xx linux-image-2.6.24-rc8-parisc linux-image-2.6.24-rc8-686 linux-image-2.6.24-rc8-xen-686 linux-image-2.6.24-rc8-mvme16x linux-headers-2.6.24-rc8-mvme147 linux-headers-2.6.24-rc8-mvme16x linux-headers-2.6.24-rc8-all-i386 linux-image-2.6.24-rc8-s390 linux-headers-2.6.24-rc8-s390-tape linux-headers-2.6.24-rc8-all-ia64 linux-headers-2.6.24-rc8-all-alpha linux-image-2.6.24-rc8-4kc-malta linux-headers-2.6.24-rc8-all linux-image-2.6.24-rc8-alpha-legacy linux-headers-2.6.24-rc8-powerpc64 linux-headers-2.6.24-rc8-4kc-malta linux-headers-2.6.24-rc8-versatile linux-headers-2.6.24-rc8-powerpc linux-headers-2.6.24-rc8-all-arm linux-image-2.6.24-rc8-sparc64 linux-headers-2.6.24-rc8-atari linux-headers-2.6.24-rc8-sb1a-bcm91480b linux-headers-2.6.24-rc8-footbridge linux-image-2.6.24-rc8-parisc-smp linux-headers-2.6.24-rc8-amd64 linux-headers-2.6.24-rc8-r4k-ip22 linux-libc-dev linux-image-2.6.24-rc8-sb1a-bcm91480b linux-image-2.6.24-rc8-mac linux-headers-2.6.24-rc8-486 linux-headers-2.6.24-rc8-parisc64-smp linux-image-2.6.24-rc8-alpha-generic linux-image-2.6.24-rc8-versatile linux-headers-2.6.24-rc8-sparc64-smp linux-image-2.6.24-rc8-mckinley linux-image-2.6.24-rc8-5kc-malta linux-headers-2.6.24-rc8-sb1-bcm91250a linux-headers-2.6.24-rc8-all-s390 linux-image-2.6.24-rc8-s390-tape linux-image-2.6.24-rc8-r5k-cobalt linux-headers-2.6.24-rc8-all-mips linux-headers-2.6.24-rc8-all-hppa linux-image-2.6.24-rc8-486 linux-image-2.6.24-rc8-amiga linux-headers-2.6.24-rc8-all-mipsel linux-headers-2.6.24-rc8-parisc64 linux-headers-2.6.24-rc8-itanium linux-headers-2.6.24-rc8-powerpc-smp linux-headers-2.6.24-rc8-alpha-smp linux-image-2.6.24-rc8-sb1-bcm91250a linux-headers-2.6.24-rc8-alpha-generic linux-headers-2.6.24-rc8-common linux-headers-2.6.24-rc8-bvme6000 linux-image-2.6.24-rc8-686-bigmem linux-image-2.6.24-rc8-atari linux-headers-2.6.24-rc8-parisc-smp linux-image-2.6.24-rc8-powerpc64 linux-headers-2.6.24-rc8-iop32x linux-tree-2.6.24 linux-image-2.6.24-rc8-powerpc-miboot linux-manual-2.6.24 linux-image-2.6.24-rc8-itanium linux-image-2.6.24-rc8-s390x linux-image-2.6.24-rc8-powerpc linux-image-2.6.24-rc8-parisc64-smp linux-headers-2.6.24-rc8-common-xen linux-image-2.6.24-rc8-mvme147 linux-headers-2.6.24-rc8-amiga linux-headers-2.6.24-rc8-r5k-cobalt linux-image-2.6.24-rc8-iop32x linux-image-2.6.24-rc8-alpha-smp linux-headers-2.6.24-rc8-all-amd64 linux-doc-2.6.24 linux-headers-2.6.24-rc8-r5k-ip32 linux-source-2.6.24 linux-image-2.6.24-rc8-bvme6000 linux-headers-2.6.24-rc8-all-armel linux-headers-2.6.24-rc8-powerpc-miboot linux-image-2.6.24-rc8-amd64 linux-headers-2.6.24-rc8-mac linux-image-2.6.24-rc8-r4k-ip22 linux-headers-2.6.24-rc8-686 linux-headers-2.6.24-rc8-5kc-malta linux-image-2.6.24-rc8-ixp4xx linux-headers-2.6.24-rc8-686-bigmem linux-headers-2.6.24-rc8-all-sparc linux-modules-2.6.24-rc8-xen-686 linux-headers-2.6.24-rc8-alpha-legacy linux-image-2.6.24-rc8-sparc64-smp linux-headers-2.6.24-rc8-s390
Architecture: source all powerpc
Version: 2.6.24~rc8-1~experimental.1
Distribution: experimental
Urgency: low
Maintainer: Debian Kernel Team <debian-kernel@lists.debian.org>
Changed-By: Bastian Blank <waldi@debian.org>
Description:
linux-doc-2.6.24 - Linux kernel specific documentation for version 2.6.24
linux-headers-2.6.24-rc8-all - All header files for Linux 2.6.24
linux-headers-2.6.24-rc8-all-powerpc - All header files for Linux 2.6.24
linux-headers-2.6.24-rc8-common - Common header files for Linux 2.6.24-rc8
linux-headers-2.6.24-rc8-powerpc - Header files for Linux 2.6.24-rc8 on uniprocessor 32-bit PowerPC
linux-headers-2.6.24-rc8-powerpc-miboot - Header files for Linux 2.6.24-rc8 on 32-bit PowerPC for miboot fl
linux-headers-2.6.24-rc8-powerpc-smp - Header files for Linux 2.6.24-rc8 on multiprocessor 32-bit PowerP
linux-headers-2.6.24-rc8-powerpc64 - Header files for Linux 2.6.24-rc8 on 64-bit PowerPC
linux-image-2.6.24-rc8-powerpc - Linux 2.6.24-rc8 image on uniprocessor 32-bit PowerPC
linux-image-2.6.24-rc8-powerpc-miboot - Linux 2.6.24-rc8 image on 32-bit PowerPC for miboot floppy
linux-image-2.6.24-rc8-powerpc-smp - Linux 2.6.24-rc8 image on multiprocessor 32-bit PowerPC
linux-image-2.6.24-rc8-powerpc64 - Linux 2.6.24-rc8 image on 64-bit PowerPC
linux-libc-dev - Linux Kernel Headers for development
linux-manual-2.6.24 - Linux kernel API manual pages for version 2.6.24
linux-patch-debian-2.6.24 - Debian patches to version 2.6.24 of the Linux kernel
linux-source-2.6.24 - Linux kernel source for version 2.6.24 with Debian patches
linux-support-2.6.24-rc8 - Support files for Linux 2.6.24-rc8
linux-tree-2.6.24 - Linux kernel source tree for building Debian kernel images
Closes: 420245 426124 433204 440807 454776 454797 455566 455892 455892 456416 457562 457992 458142 458312 458899 459732
Changes:
linux-2.6 (2.6.24~rc8-1~experimental.1) experimental; urgency=low
.
* New upstream release
(closes: #454776, #458142, #457992, #458899, #426124, #459732, #455566).
.
[ maximilian attems ]
* New upstream release, rebase dfsg stuff plus drivers-atm.patch,
scripts-kconfig-reportoldconfig.patch.
* [amd64, powerpc] Set HIGH_RES_TIMERS and NO_HZ (closes: #458312).
* topconfig set NETFILTER_XT_MATCH_TIME, NET_ACT_NAT, KSDAZZLE_DONGLE,
KS959_DONGLE, NET_9P_FD, IP1000, VETH, IXGBE, NIU, TEHUTI, LIBERTAS_CS,
LIBERTAS_SDIO, RT2X00, SENSORS_ADT7470, SENSORS_I5K_AMB, SENSORS_F71882FG,
SENSORS_FSCHMD, SENSORS_IBMPEX, CRYPTO_XTS, CRYPTO_SEED, CRYPTO_AUTHENC,
DVB_S5H1409, DVB_TUNER_MT2131, INET_LRO, MMC_RICOH_MMC, MMC_SPI,
RTC_DRV_DS1374, VIDEO_CX23885, VIDEO_FB_IVTV, USB_SERIAL_CH341,
SCSI_SRP_TGT_ATTRS, ADM8211, MTD_INTEL_VR_NOR, MTD_ALAUDA,
MTD_ONENAND_2X_PROGRAM, MTD_ONENAND_SIM, DM_MULTIPATH_HP, FUJITSU_LAPTOP,
QUOTA_NETLINK_INTERFACE, DM_UEVENT, SCSI_FC_TGT_ATTRS, SSB, BT_HCIUART_LL,
BT_HCIBTSDIO, MTD_OOPS, CGROUPS, MDIO_BITBANG, HIDRAW, P54, SDIO_UART,
NETCONSOLE_DYNAMIC, SECURITY_FILE_CAPABILITIES.
* Disable smbfs in topconfig, not supported upstream, use cifs.
* Disable bcm43xx, deprecated by upstream. Enable B43 (needs v4 firmware)
and B43LEGACY (needs v3 firmware).
* [i386]: Set SND_SC6000, EDAC_I3000, EDAC_I5000, SBC7240_WDT,
NET_9P_VIRTIO, FB_GEODE_LX, VIRTIO_NET, VIRTIO_BLK.
* Set USB_EHCI_TT_NEWSCHED fills USB 2.0 bandwith better. (closes: #454797)
* postrm: Nuke initramfs sha1sum on linux-image removal. (closes: #420245)
* Unifiy BSD_PROCESS_ACCT settings across configs. (closes: #455892)
* Reenable DABUSB as firmware is BSD licensed.
* [hppa]: Disable OCFS2, due build trouble.
* topconfig: Enable delay accounting TASKSTATS. (closes: #433204)
* Add git-ieee1394.patch for latest firewire fixes.
* [i386] Enable PARAVIRT_GUEST. (closes: #457562)
* [amd64, i386] Enable CPU_IDLE for software-controlled idle pm.
* [amd64, i386] Enable IT8712F_WDT, FB_EFI.
* Add and enable at76.patch wireless driver for Atmel USB cards.
* Add and enable ath5k.patch wireless driver for Atheros 5xxx cards.
* Unify VLAN_8021Q setting, needed also on r5k-cobalt.
* Double max SERIAL_8250_NR_UARTS to 32. (closes: #440807)
* topconfig: Enable AUDITSYSCALL for better SELinux support.
.
[ Bastian Blank ]
* [amd64, i386]: Set kernel architecture to x86.
* [i386]: Remove linux-libc-dev arch override.
.
[ Martin Michlmayr ]
* [mipsel/r5k-cobalt] Enable the new LEDs driver for Cobalt RaQ.
* [arm/iop32x] Re-enable USB_NET and PPP, thanks Daniel Hess (closes:
#456416).
* [arm/iop32x] Enable BSD_PROCESS_ACCT and POSIX_MQUEUE (closes: #455892).
* [mips] Disable AdvanSys SCSI since it doesn't compile.
* [arm/ixp4xx] Enable IP_ADVANCED_ROUTER, requested by Oliver Urbann.
* [arm/iop32x] Enable IP_ADVANCED_ROUTER.
.
[ dann frazier ]
* [ia64]: Enable BLK_CPQ_DA
.
[ Frederik Schüler ]
* Add GFS2 locking symbols export patch.
.
[ Aurelien Jarno ]
* [mips/mipsel] Remove QEMU flavour, as the Malta platform is now correctly
emulated in QEMU.
.
[ Christian T. Steigies ]
* [m68k]: Update patches from linux-m68k CVS
* [m68k]: Enable building for bvme6000, mvme147, and mvme16x again
Files:
afd2f41b686e0d8f763534bb57ab77e3 4568 devel optional linux-2.6_2.6.24~rc8-1~experimental.1.dsc
b7e3338b437ec49037e51f9d12e95c9f 58512156 devel optional linux-2.6_2.6.24~rc8.orig.tar.gz
afd03412af9e000aab8ee401172cbc47 908333 devel optional linux-2.6_2.6.24~rc8-1~experimental.1.diff.gz
ae0d073eecd8ae9fb5b75e2856e1a7bf 4276664 doc optional linux-doc-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
8ed774a38f8518685ecc5db01db83210 1549140 doc optional linux-manual-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
6a933b0d7fe03ea5d7e09cfb5d9a42be 600204 devel optional linux-patch-debian-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
387ee6e9cccf0e272ea95b11e46f96c5 45933244 devel optional linux-source-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
b0d7ed7dfd858a92fdf6f30083b53c12 85348 devel optional linux-support-2.6.24-rc8_2.6.24~rc8-1~experimental.1_all.deb
86bb54a5c6a6d9994fb49f3c3e181b3d 70886 devel optional linux-tree-2.6.24_2.6.24~rc8-1~experimental.1_all.deb
7549b30c31b3f1b8c1a6886cd414fb49 19062090 admin optional linux-image-2.6.24-rc8-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
20ea50578e5fac5d30253f86a3e1dada 304966 devel optional linux-headers-2.6.24-rc8-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
79c4fee9fcfaa86a3d5aeb805d8aea6d 17372892 admin optional linux-image-2.6.24-rc8-powerpc-miboot_2.6.24~rc8-1~experimental.1_powerpc.deb
d737e5cff9f6c1da5feb77c23c9909c7 279492 devel optional linux-headers-2.6.24-rc8-powerpc-miboot_2.6.24~rc8-1~experimental.1_powerpc.deb
b9ac8072b2d5e8ba654032b816e0c5c4 19401914 admin optional linux-image-2.6.24-rc8-powerpc-smp_2.6.24~rc8-1~experimental.1_powerpc.deb
6b2dd9fa7379b104aadead5aeecb6392 305140 devel optional linux-headers-2.6.24-rc8-powerpc-smp_2.6.24~rc8-1~experimental.1_powerpc.deb
2bf4efdeb0d5d3e253189ca8f3a75e6d 21044798 admin optional linux-image-2.6.24-rc8-powerpc64_2.6.24~rc8-1~experimental.1_powerpc.deb
1e765018857244be9eb132c62a02e5a3 307226 devel optional linux-headers-2.6.24-rc8-powerpc64_2.6.24~rc8-1~experimental.1_powerpc.deb
848b41cfe148d6939bfc74ef86476609 3895082 devel optional linux-headers-2.6.24-rc8-common_2.6.24~rc8-1~experimental.1_powerpc.deb
45a5271bb316e439ded9cc330df41797 70540 devel optional linux-headers-2.6.24-rc8-all_2.6.24~rc8-1~experimental.1_powerpc.deb
513e4b643306df1ddb450b0d68ba0a69 70576 devel optional linux-headers-2.6.24-rc8-all-powerpc_2.6.24~rc8-1~experimental.1_powerpc.deb
d6ae1467a7407072c54fe9fb5153c16f 710404 devel optional linux-libc-dev_2.6.24~rc8-1~experimental.1_powerpc.deb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.6 (GNU/Linux)
iEYEARECAAYFAkeQnWwACgkQxWtQqFixGB5ZxgCeOqmmqddDRJItf8+xo7kI4BYT
tX4AoJNz3Cf1juuONBPDYXufeGUBXLcK
=GYaQ
-----END PGP SIGNATURE-----
--- End Message ---