Bug#369363: sn9c102: more info (posible solution)
Package: linux-image-2.6.23-1-amd64
Version: 2.6.23-2
Followup-For: Bug #369363
Hi I own a Genius videoCam messenger webcam.
#lsusb
Bus 003 Device 002: ID 0c45:602e Microdia
same chipset as in this bug report.
The kernel image tries to use sn9c102 built in. This driver dos not work. I get some sort of green input from the cam.
Yet there is a Gspca-souce package in debian containing driver which does a much better job at supporting the cam. It is still limited but it gives a
much
better image.
The problem is that to use gspca module the sn9c102 module must be black listed in etc/modprobe.d/blacklist so that gspca takes control of the webcam.
I have the feeling that sn9c102 is the old form of the gspca driver.
The sn9c102 driver could be left out of the linux image so not to conflict with gspca (user would have to install the module to get webcam support).
Mail me for any clarification or further information.
-- Package-specific info:
** Version:
Linux version 2.6.23-1-amd64 (Debian 2.6.23-2) (maks@debian.org) (gcc version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #1 SMP Fri Dec 21 12:00:17 UTC 2007
** cmdline:
root=/dev/sda8 ro vga=792 quiet
** Tainted: P (1)
** Kernel log:
usb 3-2: new full speed USB device using uhci_hcd and address 2
hda: TSSTcorpDVD-ROM TS-H352C, ATAPI CD/DVD-ROM drive
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft IntelliMouse� Optical as /class/input/input1
input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse� Optical] on usb-0000:00:1d.0-1
input: DELL DELL USB Keyboard as /class/input/input2
input: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-0000:00:1d.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
hdb: _NEC DVD+/-RW ND-3530A, ATAPI CD/DVD-ROM drive
hda: selected mode 0x42
hdb: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Attempting manual resume
swsusp: Marking nosave pages: 00000000000a0000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access Samsung CF Card CF 1.6E PQ: 0 ANSI: 0 CCS
scsi 4:0:0:1: Direct-Access Samsung MS Card MS 1.6E PQ: 0 ANSI: 0 CCS
scsi 4:0:0:2: Direct-Access Samsung SD Card MMC/SD 1.6E PQ: 0 ANSI: 0 CCS
scsi 4:0:0:3: Direct-Access Samsung SM/XD Card SM 1.6E PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: [sdb] Attached SCSI removable disk
sd 4:0:0:1: [sdc] Attached SCSI removable disk
sd 4:0:0:2: [sdd] Attached SCSI removable disk
sd 4:0:0:3: [sde] Attached SCSI removable disk
input: PC Speaker as /class/input/input3
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [VBTN]
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected
Linux video capture interface: v2.00
/usr/src/modules/gspca/gspca_core.c: USB GSPCA camera found. SONIX sn9c10[1 2]
/usr/src/modules/gspca/gspca_core.c: [spca5xx_probe:4098] Camera type SN9C
/usr/src/modules/gspca/gspca_core.c: [spca5xx_getcapability:1215] maxw 640 maxh 480 minw 160 minh 120
usbcore: registered new interface driver gspca
/usr/src/modules/gspca/gspca_core.c: gspca driver 01.00.18 registered
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
Adding 1052216k swap on /dev/sda5. Priority:-1 extents:1 across:1052216k
EXT3 FS on sda8, internal journal
loop: module loaded
fuse init (API version 7.8)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007
eth0: no IPv6 routers present
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: VIDIOCMCAPTURE: invalid format (7)
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
/usr/src/modules/gspca/gspca_core.c: [spca5xx_set_light_freq:1889] Sensor currently not support light frequency banding filters.
/usr/src/modules/gspca/gspca_core.c: [gspca_set_isoc_ep:903] ISO EndPoint found 0x81 AlternateSet 8
npviewer.bin[3791]: segfault at 0000000000000084 rip 00000000f7b7b89a rsp 00000000f5aac020 error 4
usb 5-3: reset high speed USB device using ehci_hcd and address 4
usb 5-3: reset high speed USB device using ehci_hcd and address 4
** Loaded modules:
Module Size Used by
nvidia 7011220 34
ppdev 13832 0
parport_pc 42664 0
lp 17480 0
parport 44428 3 ppdev,parport_pc,lp
ipv6 303336 20
ac 10760 0
battery 18064 0
acpi_cpufreq 13712 0
cpufreq_stats 10400 0
cpufreq_conservative 12424 0
cpufreq_userspace 9604 0
cpufreq_powersave 6272 0
cpufreq_ondemand 13456 2
freq_table 9728 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
fuse 50480 3
loop 23428 0
snd_hda_intel 339364 2
snd_pcm_oss 48288 0
snd_pcm 89864 2 snd_hda_intel,snd_pcm_oss
snd_mixer_oss 21376 1 snd_pcm_oss
snd_seq_dummy 8452 0
snd_seq_oss 36736 0
snd_seq_midi 13376 0
snd_rawmidi 30624 1 snd_seq_midi
snd_seq_midi_event 12416 2 snd_seq_oss,snd_seq_midi
snd_seq 58752 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
gspca 654928 0
snd_timer 28552 2 snd_pcm,snd_seq
snd_seq_device 12948 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 65640 13 snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
compat_ioctl32 13184 1 gspca
videodev 32640 1 gspca
v4l2_common 24320 2 compat_ioctl32,videodev
v4l1_compat 16388 1 videodev
iTCO_wdt 17232 0
i2c_i801 13980 0
serio_raw 11908 0
button 13856 0
soundcore 13216 1 snd
pcspkr 7808 0
i2c_core 30976 2 nvidia,i2c_i801
psmouse 45596 0
intel_agp 32160 0
snd_page_alloc 15248 2 snd_hda_intel,snd_pcm
evdev 15360 3
tsdev 13440 0
ext3 137488 3
jbd 68080 1 ext3
mbcache 13952 1 ext3
ide_cd 44704 0
cdrom 39592 1 ide_cd
sd_mod 33408 6
piix 15236 0 [permanent]
usbhid 34144 0
hid 33152 1 usbhid
usb_storage 91200 0
generic 10372 0 [permanent]
ide_core 149904 4 ide_cd,piix,usb_storage,generic
floppy 66984 0
ata_generic 13188 0
e100 42256 0
mii 10240 1 e100
ahci 30468 5
libata 129840 2 ata_generic,ahci
scsi_mod 164664 3 sd_mod,usb_storage,libata
ehci_hcd 38540 0
uhci_hcd 29984 0
thermal 22176 0
processor 43624 2 acpi_cpufreq,thermal
fan 10248 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770]
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port [8086:2771] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fc000000-feafffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: fbf00000-fbffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.4 PCI bridge [0604]: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 [8086:27e0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.5 PCI bridge [0604]: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 [8086:27e2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at ff80 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at ff60 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ff40 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at ff20 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbe00000-fbefffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 SATA controller [0106]: Intel Corporation 82801GR/GH (ICH7 Family) Serial ATA Storage Controller AHCI [8086:27c1] (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 1275
Region 0: I/O ports at fe00 [size=8]
Region 1: I/O ports at fe10 [size=4]
Region 2: I/O ports at fe20 [size=8]
Region 3: I/O ports at fe30 [size=4]
Region 4: I/O ports at fea0 [size=16]
Region 5: Memory at febfbc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at ece0 [size=32]
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV41.1 [GeForce 6800] [10de:00c1] (rev a2) (prog-if 00 [VGA])
Subsystem: nVidia Corporation Unknown device [10de:0245]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fd000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at fea00000 [disabled] [size=128K]
Capabilities: <access denied>
05:05.0 Modem [0703]: Intel Corporation FA82537EP 56K V.92 Data/Fax Modem PCI [8086:1080] (rev 04) (prog-if 00 [Generic])
Subsystem: Dell Unknown device [1028:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 15500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbefe000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at dc00 [size=256]
Capabilities: <access denied>
05:08.0 Ethernet controller [0200]: Intel Corporation 82801G (ICH7 Family) LAN Controller [8086:27dc] (rev 01)
Subsystem: Dell Unknown device [1028:01a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fbeff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d8c0 [size=64]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.23-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=es_CR.UTF-8, LC_CTYPE=es_CR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.23-1-amd64 depends on:
ii e2fsprogs 1.40.3-1 ext2 file system utilities and lib
ii initramfs-tools [linux-initr 0.91d tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.23-1-amd64 recommends no packages.
-- debconf information:
linux-image-2.6.23-1-amd64/postinst/depmod-error-2.6.23-1-amd64: false
linux-image-2.6.23-1-amd64/postinst/bootloader-error-2.6.23-1-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.23-1-amd64/preinst/abort-install-2.6.23-1-amd64:
linux-image-2.6.23-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.23-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.23-1-amd64/preinst/elilo-initrd-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/preinst/bootloader-initrd-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/preinst/lilo-initrd-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/postinst/bootloader-test-error-2.6.23-1-amd64:
linux-image-2.6.23-1-amd64/postinst/old-dir-initrd-link-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/postinst/depmod-error-initrd-2.6.23-1-amd64: false
linux-image-2.6.23-1-amd64/preinst/overwriting-modules-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/preinst/abort-overwrite-2.6.23-1-amd64:
linux-image-2.6.23-1-amd64/preinst/initrd-2.6.23-1-amd64:
linux-image-2.6.23-1-amd64/postinst/create-kimage-link-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/postinst/old-system-map-link-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/prerm/removing-running-kernel-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/prerm/would-invalidate-boot-loader-2.6.23-1-amd64: true
linux-image-2.6.23-1-amd64/preinst/already-running-this-2.6.23-1-amd64:
linux-image-2.6.23-1-amd64/preinst/failed-to-move-modules-2.6.23-1-amd64:
linux-image-2.6.23-1-amd64/postinst/old-initrd-link-2.6.23-1-amd64: true
Reply to: