Bug#441206: linux-image-2.6.22-2-k7: Firewire 400 external HD fails to be recognized
Package: linux-image-2.6.22-2-k7
Version: 2.6.22-4
Severity: important
My Western Digital 500GB MyBook external HD fails to be recognized when
I plug it through the Firewire 400 port. The following errors appear on
the syslog:
Sep 7 09:41:18 monk kernel: scsi0 : SBP-2 IEEE-1394
Sep 7 09:41:18 monk kernel: firewire_core: created new fw device fw1 (0 config rom retries)
Sep 7 09:41:18 monk kernel: firewire_sbp2: logged in to sbp2 unit fw1.1 (0 retries)
Sep 7 09:41:18 monk kernel: firewire_sbp2: - management_agent_address: 0xfffff0030000
Sep 7 09:41:18 monk kernel: firewire_sbp2: - command_block_agent_address: 0xfffff0100000
Sep 7 09:41:18 monk kernel: firewire_sbp2: - status write address: 0x000100000000
Sep 7 09:41:24 monk kernel: firewire_sbp2: sbp2_scsi_abort
Sep 7 09:41:29 monk kernel: scsi 0:0:0:0: Direct-Access WD 5000AAKS Externa 107a PQ: 0 ANSI: 4
Sep 7 09:41:29 monk kernel: firewire_core: phy config: card 0, new root=ffc0, gap_count=63
Sep 7 09:41:29 monk kernel: firewire_sbp2: management write failed, rcode 0x12
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] READ CAPACITY failed
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Result: hostbyte=DID_BUS_BUSY driverbyte=DRIVER_OK,SUGGEST_OK
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Sense not available.
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Write Protect is off
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Asking for cache data failed
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Sep 7 09:41:29 monk kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Sep 7 09:41:29 monk kernel: firewire_sbp2: reconnected to unit fw1.1 (1 retries)
The same HD also failed to be recognized by previous kernel version
linux-image-2.6.22-1-k7, but the error messages were different. This is
filed under bug #435224.
It's correctly recognized if I plug it through the USB port.
Regards,
Paulo
-- Package-specific info:
** Version:
Linux version 2.6.22-2-k7 (Debian 2.6.22-4) (waldi@debian.org) (gcc version 4.1.3 20070812 (prerelease) (Debian 4.1.2-15)) #1 SMP Fri Aug 31 01:02:37 UTC 2007
** Not tainted
** Kernel log:
Real Time Clock Driver v1.12ac
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
input: PC Speaker as /class/input/input2
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
bcm43xx driver
Yenta: ISA IRQ mask 0x0ef8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xb0200000 - 0xb02fffff
pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
sdhci: SDHCI controller found at 0000:03:04.4 [104c:8034] (rev 0)
ACPI: PCI Interrupt 0000:03:04.4[D] -> GSI 23 (level, low) -> IRQ 22
mmc0: SDHCI at 0xb020a000 irq 22 DMA
mmc1: SDHCI at 0xb0208c00 irq 22 DMA
mmc2: SDHCI at 0xb0208800 irq 22 DMA
ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
MC'97 0 converters and GPIO not ready (0x1)
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 21 (level, low) -> IRQ 21
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x23a0b1, caps: 0xa04713/0x200000
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f
input: SynPS/2 Synaptics TouchPad as /class/input/input3
cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
cs: IO port probe 0xa00-0xaff: clean.
Adding 1951856k swap on /dev/hda5. Priority:-1 extents:1 across:1951856k
EXT3 FS on hda3, internal journal
loop: module loaded
ACPI: Battery Slot [BAT1] (battery present)
fuse init (API version 7.8)
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ACPI: AC Adapter [ACAD] (on-line)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x2
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x6
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x10
Marking TSC unstable due to: cpufreq changes.
Time: acpi_pm clocksource has been installed.
Clocksource tsc unstable (delta = -272756734 ns)
eth0: no IPv6 routers present
scsi0 : SBP-2 IEEE-1394
firewire_core: created new fw device fw1 (0 config rom retries)
firewire_sbp2: logged in to sbp2 unit fw1.1 (0 retries)
firewire_sbp2: - management_agent_address: 0xfffff0030000
firewire_sbp2: - command_block_agent_address: 0xfffff0100000
firewire_sbp2: - status write address: 0x000100000000
firewire_sbp2: sbp2_scsi_abort
scsi 0:0:0:0: Direct-Access WD 5000AAKS Externa 107a PQ: 0 ANSI: 4
firewire_core: phy config: card 0, new root=ffc0, gap_count=63
firewire_sbp2: management write failed, rcode 0x12
sd 0:0:0:0: [sda] READ CAPACITY failed
sd 0:0:0:0: [sda] Result: hostbyte=DID_BUS_BUSY driverbyte=DRIVER_OK,SUGGEST_OK
sd 0:0:0:0: [sda] Sense not available.
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
sd 0:0:0:0: [sda] Asking for cache data failed
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI disk
firewire_sbp2: reconnected to unit fw1.1 (1 retries)
** Loaded modules:
Module Size Used by
sd_mod 27584 0
cpufreq_ondemand 8652 1
cpufreq_userspace 4448 0
cpufreq_powersave 2112 0
powernow_k8 14976 0
freq_table 4832 2 cpufreq_ondemand,powernow_k8
ipv6 239524 8
ppdev 8964 0
parport_pc 34212 0
lp 11300 0
parport 34312 3 ppdev,parport_pc,lp
button 8208 0
ac 5508 0
fuse 42388 3
battery 10308 0
firewire_sbp2 12548 0
loop 17412 0
joydev 9920 0
pcmcia 37548 0
bcm43xx 417248 0
firmware_class 9984 2 pcmcia,bcm43xx
serio_raw 7044 0
snd_atiixp_modem 15624 2
snd_pcm_oss 39904 0
snd_mixer_oss 15872 1 snd_pcm_oss
ieee80211softmac 27904 1 bcm43xx
ieee80211 32904 2 bcm43xx,ieee80211softmac
ieee80211_crypt 6080 1 ieee80211
snd_atiixp 19340 2
pcspkr 3392 0
sdhci 16844 0
psmouse 36432 0
snd_ac97_codec 93220 2 snd_atiixp_modem,snd_atiixp
rtc 13144 0
yenta_socket 25100 1
rsrc_nonstatic 12288 1 yenta_socket
pcmcia_core 37588 3 pcmcia,yenta_socket,rsrc_nonstatic
k8temp 5824 0
mmc_core 26436 1 sdhci
tifm_7xx1 7680 0
tifm_core 10500 1 tifm_7xx1
ac97_bus 2560 1 snd_ac97_codec
snd_pcm 72772 4 snd_atiixp_modem,snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer 21380 1 snd_pcm
snd 48804 15 snd_atiixp_modem,snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
soundcore 7840 1 snd
snd_page_alloc 9800 3 snd_atiixp_modem,snd_atiixp,snd_pcm
i2c_piix4 8844 0
shpchp 31380 0
pci_hotplug 29568 1 shpchp
i2c_core 24000 1 i2c_piix4
ati_agp 9036 0
agpgart 32264 1 ati_agp
tsdev 8320 0
evdev 9664 5
ext3 122632 5
jbd 55848 1 ext3
mbcache 8580 1 ext3
dm_mirror 21376 0
dm_snapshot 16804 0
dm_mod 52672 11 dm_mirror,dm_snapshot
ide_cd 36896 0
cdrom 33184 1 ide_cd
ide_disk 16832 6
8139too 25984 0
ata_generic 7876 0
libata 116912 1 ata_generic
scsi_mod 137356 3 sd_mod,firewire_sbp2,libata
usbhid 26144 0
hid 25792 1 usbhid
atiixp 5968 0 [permanent]
8139cp 22528 0
mii 5696 2 8139too,8139cp
firewire_ohci 16960 0
firewire_core 39424 2 firewire_sbp2,firewire_ohci
crc_itu_t 2432 1 firewire_core
generic 5124 0 [permanent]
ide_core 114436 4 ide_cd,ide_disk,atiixp,generic
ehci_hcd 31116 0
ohci_hcd 20036 0
usbcore 125704 4 usbhid,ehci_hcd,ohci_hcd
thermal 13768 0
processor 31368 2 powernow_k8,thermal
fan 5124 0
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS480 Host Bridge [1002:5950]
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: b0100000-b01fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:04.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a36] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:13.0 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4374] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4374]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:13.1 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4375] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4375]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at b0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:13.2 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB2 Host Controller [1002:4373] (prog-if 20 [EHCI])
Subsystem: ATI Technologies Inc IXP SB400 USB2 Host Controller [1002:4373]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at b0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:14.0 SMBus [0c05]: ATI Technologies Inc IXP SB400 SMBus Controller [1002:4372] (rev 10)
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 8400 [size=16]
Region 1: Memory at b0003000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:14.1 IDE interface [0101]: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI [1002:4376] (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 8410 [size=16]
Capabilities: <access denied>
00:14.3 ISA bridge [0601]: ATI Technologies Inc IXP SB400 PCI-ISA Bridge [1002:4377]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc IXP SB400 PCI-PCI Bridge [1002:4371] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=03, subordinate=07, sec-latency=64
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: b0200000-b02fffff
Prefetchable memory behind bridge: 60000000-63ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:14.5 Multimedia audio controller [0401]: ATI Technologies Inc IXP SB400 AC'97 Audio Controller [1002:4370] (rev 01)
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at b0003400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:14.6 Modem [0703]: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller [1002:4378] (rev 01) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at b0003800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc ATI Radeon XPRESS 200M 5955 (PCIE) [1002:5955] (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at b0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at b0120000 [disabled] [size=128K]
Capabilities: <access denied>
03:00.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0208000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at b0200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
03:02.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Hewlett-Packard Company Unknown device [103c:12f8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 21
Region 0: Memory at b0204000 (32-bit, non-prefetchable) [size=8K]
03:04.0 CardBus bridge [0607]: Texas Instruments PCIxx21/x515 Cardbus Controller [104c:8031]
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0209000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 60000000-63fff000 (prefetchable)
Memory window 1: 64000000-67fff000
I/O window 0: 0000a400-0000a4ff
I/O window 1: 0000a800-0000a8ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
03:04.3 Mass storage controller [0180]: Texas Instruments PCIxx21 Integrated FlashMedia Controller [104c:8033]
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at b0206000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
03:04.4 Generic system peripheral [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller [104c:8034]
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 22
Region 0: Memory at b020a000 (32-bit, non-prefetchable) [size=256]
Region 1: Memory at b0208c00 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at b0208800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Hewlett-Packard Company Unknown device [103c:3085]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 128 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at b020a400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-2-k7 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-2-k7 depends on:
ii initramfs-tools [linux-initr 0.90a tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-2-k7 recommends:
ii libc6-i686 2.6.1-2 GNU C Library: Shared libraries [i
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-2-k7/preinst/lilo-initrd-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/preinst/lilo-has-ramdisk:
linux-image-2.6.22-2-k7/preinst/already-running-this-2.6.22-2-k7:
linux-image-2.6.22-2-k7/postinst/depmod-error-initrd-2.6.22-2-k7: false
linux-image-2.6.22-2-k7/postinst/kimage-is-a-directory:
linux-image-2.6.22-2-k7/postinst/bootloader-test-error-2.6.22-2-k7:
linux-image-2.6.22-2-k7/postinst/bootloader-error-2.6.22-2-k7:
linux-image-2.6.22-2-k7/preinst/abort-overwrite-2.6.22-2-k7:
linux-image-2.6.22-2-k7/preinst/elilo-initrd-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/prerm/removing-running-kernel-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/preinst/abort-install-2.6.22-2-k7:
linux-image-2.6.22-2-k7/prerm/would-invalidate-boot-loader-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/preinst/failed-to-move-modules-2.6.22-2-k7:
linux-image-2.6.22-2-k7/preinst/overwriting-modules-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/postinst/old-system-map-link-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/postinst/create-kimage-link-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/preinst/bootloader-initrd-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/postinst/depmod-error-2.6.22-2-k7: false
linux-image-2.6.22-2-k7/postinst/old-initrd-link-2.6.22-2-k7: true
linux-image-2.6.22-2-k7/preinst/initrd-2.6.22-2-k7:
linux-image-2.6.22-2-k7/postinst/old-dir-initrd-link-2.6.22-2-k7: true
Reply to: