Bug#433103: linux-image-2.6.21-2-686: Non GPL closed source drivers accepted
Package: linux-image-2.6.21-2-686
Version: 2.6.21-5
Severity: important
After upgrading to linux-image-2.6.21-2-686 I cant compile
drivers with closed source parts, in my case a fax driver
for a old AVM ISDN pci card, because the kernel does not accecpt
non GPL drivers.
I get the following error message:
make[2]: Entering directory `/usr/src/linux-headers-2.6.21-2-686'
Building modules, stage 2.
MODPOST 1 modules
FATAL: modpost: GPL-incompatible module fcpci.ko uses GPL-only symbol
'paravirt_ops'
-- Package-specific info:
** Version: Linux version 2.6.21-2-686 (Debian 2.6.21-5) (waldi@debian.org) (gcc version 4.1.3 20070601 (prerelease) (Debian 4.1.2-12)) #1 SMP Mon Jun 25 20:53:36 UTC 2007
** Not tainted
** Kernel log:
hdd: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
8139cp 0000:00:0a.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:00:0a.0: Try the "8139too" driver instead.
8139cp 0000:00:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:00:0c.0: Try the "8139too" driver instead.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[de014000-de0147ff] Max Packet=[2048] IR/IT contexts=[4/8]
SCSI subsystem initialized
libata version 2.20 loaded.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xe000, 00:40:f4:1e:c6:0f, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
eth1: RealTek RTL8139 at 0xe400, 00:30:84:77:ff:f8, IRQ 10
eth1: Identified 8139 chip type 'RTL-8139C'
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/512KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/2000KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
hdc: ATAPI 48X DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00506256000001d1]
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
input: PC Speaker as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport0: Printer, Hewlett-Packard HP LaserJet 5L
parport_pc: VIA parallel port: io=0x378, irq=7
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xd8000000
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:01:87:b3
b2c2-flexcop: found the stv0299 at i2c address: 0x68
DVB: registering frontend 0 (ST STV0299 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopII' complete
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:07.5 to 64
Adding 1534168k swap on /dev/hda11. Priority:42 extents:1 across:1534168k
EXT3 FS on hda1, internal journal
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
ReiserFS: hdb2: found reiserfs format "3.6" with standard journal
ReiserFS: hdb2: using ordered data mode
ReiserFS: hdb2: journal params: device hdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb2: checking transaction log (hdb2)
ReiserFS: hdb2: Using r5 hash to sort names
ReiserFS: hdb3: found reiserfs format "3.6" with standard journal
ReiserFS: hdb3: using ordered data mode
ReiserFS: hdb3: journal params: device hdb3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb3: checking transaction log (hdb3)
ReiserFS: hdb3: Using r5 hash to sort names
ReiserFS: hdb5: found reiserfs format "3.6" with standard journal
ReiserFS: hdb5: using ordered data mode
ReiserFS: hdb5: journal params: device hdb5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb5: checking transaction log (hdb5)
ReiserFS: hdb5: Using r5 hash to sort names
eth1: link down
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
capifs: Rev 1.1.2.3
CAPI Subsystem Rev 1.1.2.8
capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
eth0: no IPv6 routers present
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
** Loaded modules:
Module Size Used by
tcp_diag 1760 0
inet_diag 11336 1 tcp_diag
nfs 222444 0
nfsd 202800 17
exportfs 5472 1 nfsd
lockd 58248 3 nfs,nfsd
nfs_acl 3520 2 nfs,nfsd
sunrpc 154972 13 nfs,nfsd,lockd,nfs_acl
ppdev 8580 0
lp 10884 0
capi 16672 4
kernelcapi 37908 1 capi
capifs 5640 2 capi
ipv6 236256 25
reiserfs 220224 4
dm_snapshot 16420 0
dm_mirror 20116 0
dm_mod 52556 2 dm_snapshot,dm_mirror
ide_generic 1344 0 [permanent]
snd_via82xx 26904 7
gameport 14984 1 snd_via82xx
snd_ac97_codec 92356 1 snd_via82xx
ac97_bus 2272 1 snd_ac97_codec
snd_pcm_oss 39168 0
snd_mixer_oss 15328 1 snd_pcm_oss
snd_pcm 71940 6 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 9512 2 snd_via82xx,snd_pcm
snd_mpu401_uart 8032 1 snd_via82xx
snd_seq_dummy 3748 0
snd_seq_oss 29248 0
tsdev 7520 0
snd_seq_midi 8160 0
snd_seq_midi_event 6880 2 snd_seq_oss,snd_seq_midi
snd_seq 46160 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
rtc 12760 0
snd_timer 20868 5 snd_pcm,snd_seq
snd_rawmidi 22400 2 snd_mpu401_uart,snd_seq_midi
snd_seq_device 7596 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd 48132 19 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_seq,snd_timer,snd_rawmidi,snd_seq_device
stv0299 9672 1
soundcore 7424 1 snd
psmouse 34952 0
b2c2_flexcop_pci 8344 0
b2c2_flexcop 25516 1 b2c2_flexcop_pci
serio_raw 6564 0
dvb_core 73640 2 stv0299,b2c2_flexcop
via686a 15304 0
firmware_class 9408 1 b2c2_flexcop
via_agp 10016 1
agpgart 32168 1 via_agp
dvb_pll 14084 1 b2c2_flexcop
evdev 9216 1
i2c_isa 5216 1 via686a
i2c_viapro 8660 0
i2c_core 20480 6 stv0299,b2c2_flexcop,via686a,dvb_pll,i2c_isa,i2c_viapro
parport_pc 32740 1
parport 33672 3 ppdev,lp,parport_pc
shpchp 30996 0
pci_hotplug 29088 1 shpchp
pcspkr 3136 0
eth1394 18276 0
ext3 120904 1
jbd 55208 1 ext3
mbcache 8164 1 ext3
ide_cd 36512 0
cdrom 32768 1 ide_cd
ide_disk 15648 8
ata_generic 8100 0
8139too 25536 0
libata 109172 1 ata_generic
scsi_mod 133740 1 libata
floppy 54820 0
via82cxxx 8676 0 [permanent]
ohci1394 32432 0
8139cp 22336 0
mii 5280 2 8139too,8139cp
ieee1394 89560 2 eth1394,ohci1394
generic 4804 0 [permanent]
ide_core 115016 5 ide_generic,ide_cd,ide_disk,via82cxxx,generic
uhci_hcd 22608 0
usbcore 123272 2 uhci_hcd
thermal 14120 0
processor 30888 1 thermal
fan 4868 0
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] [1106:0305] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] [1106:8305] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:07.0 ISA bridge [0601]: VIA Technologies, Inc. VT82C686 [Apollo Super South] [1106:0686] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge [1106:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:07.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at c000 [size=16]
Capabilities: <access denied>
00:07.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at c400 [size=32]
Capabilities: <access denied>
00:07.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at c800 [size=32]
Capabilities: <access denied>
00:07.4 Host bridge [0600]: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] [1106:3057] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 11
Capabilities: <access denied>
00:07.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT82C686 AC97 Audio Controller [1106:3058] (rev 50)
Subsystem: Micro-Star International Co., Ltd. MS-6330 Onboard Audio [1462:3300]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at cc00 [size=256]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: <access denied>
00:08.0 Network controller [0280]: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] (rev 01)
Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=64K]
Region 1: I/O ports at dc00 [size=32]
00:09.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB12LV26 IEEE-1394 Controller (Link) [104c:8020] (prog-if 10 [OHCI])
Subsystem: Texas Instruments Unknown device [104c:8010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de014000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at de010000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:0a.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size=256]
Region 1: Memory at de015000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:0c.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Allied Telesyn International AT-2500TX/ACPI [1259:2503]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at de016000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:0d.0 Network controller [0280]: AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz] [1244:0a00] (rev 02)
Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH FRITZ!Card ISDN Controller [1244:0a00]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de017000 (32-bit, non-prefetchable) [size=32]
Region 1: I/O ports at e800 [size=32]
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV11 [GeForce2 MX/MX 400] [10de:0110] (rev b2) (prog-if 00 [VGA])
Subsystem: Guillemot Corporation Unknown device [14af:710a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at dd000000 [disabled] [size=64K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.21-2-686 (SMP w/1 CPU core)
Locale: LANG=de_DE@euro, LC_CTYPE=de_DE@euro (charmap=ISO-8859-15)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.21-2-686 depends on:
ii initramfs-tools [linux-initr 0.89 tools for generating an initramfs
ii module-init-tools 3.3-pre11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.21-2-686 recommends:
pn libc6-i686 <none> (no description available)
-- debconf information:
linux-image-2.6.21-2-686/preinst/elilo-initrd-2.6.21-2-686: true
linux-image-2.6.21-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.21-2-686/preinst/already-running-this-2.6.21-2-686:
linux-image-2.6.21-2-686/postinst/depmod-error-initrd-2.6.21-2-686: false
linux-image-2.6.21-2-686/postinst/bootloader-test-error-2.6.21-2-686:
linux-image-2.6.21-2-686/prerm/removing-running-kernel-2.6.21-2-686: true
linux-image-2.6.21-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.21-2-686/preinst/failed-to-move-modules-2.6.21-2-686:
linux-image-2.6.21-2-686/preinst/initrd-2.6.21-2-686:
linux-image-2.6.21-2-686/preinst/overwriting-modules-2.6.21-2-686: true
linux-image-2.6.21-2-686/postinst/create-kimage-link-2.6.21-2-686: true
linux-image-2.6.21-2-686/postinst/old-system-map-link-2.6.21-2-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.21-2-686/prerm/would-invalidate-boot-loader-2.6.21-2-686: true
linux-image-2.6.21-2-686/postinst/old-initrd-link-2.6.21-2-686: true
linux-image-2.6.21-2-686/postinst/bootloader-error-2.6.21-2-686:
linux-image-2.6.21-2-686/preinst/lilo-initrd-2.6.21-2-686: true
linux-image-2.6.21-2-686/preinst/bootloader-initrd-2.6.21-2-686: true
linux-image-2.6.21-2-686/postinst/old-dir-initrd-link-2.6.21-2-686: true
linux-image-2.6.21-2-686/preinst/abort-overwrite-2.6.21-2-686:
linux-image-2.6.21-2-686/postinst/depmod-error-2.6.21-2-686: false
linux-image-2.6.21-2-686/preinst/abort-install-2.6.21-2-686:
Reply to: