Bug#443197: linux-image-2.6.22-2-amd64: Kernel sometimes fails to detect ide disk correctly
Package: linux-image-2.6.22-2-amd64
Version: 2.6.22-4
Severity: critical
Justification: breaks the whole system
The kernel sometimes fails to detect or name the ide disk hdb correctly and calls it hdf instead
(ok, this might be a udev problem). The system then is unbootable. The error occurs about every
third boot. So far rebooting has always fixed the problem. This problem did not occur with 2.6.18
or 2.6.21. I have not modified udev.rules.
-- Package-specific info:
** Version:
Linux version 2.6.22-2-amd64 (Debian 2.6.22-4) (waldi@debian.org) (gcc version 4.1.3 20070812 (prerelease) (Debian 4.1.2-15)) #1 SMP Thu Aug 30 23:43:59 UTC 2007
** Not tainted
** Kernel log:
JMB363: 100% native mode on irq 29
PCI: Setting latency timer of device 0000:03:00.1 to 64
ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23
eth0: VIA Rhine II at 0x1d000, 00:17:31:83:16:0b, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
usb 2-1: USB disconnect, address 2
Probing IDE interface ide3...
usb 2-1: new low speed USB device using uhci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
usb 2-2: USB disconnect, address 3
usb 2-2: new low speed USB device using uhci_hcd and address 5
sata_via 0000:00:0f.0: version 2.2
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 21
sata_via 0000:00:0f.0: routed to hard irq line 11
scsi2 : sata_via
scsi3 : sata_via
ata3: SATA max UDMA/133 cmd 0x000000000001fc00 ctl 0x000000000001f802 bmdma 0x000000000001ec00 irq 21
ata4: SATA max UDMA/133 cmd 0x000000000001f400 ctl 0x000000000001f002 bmdma 0x000000000001ec08 irq 21
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 >
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.1-1
input: USB Keyboard as /class/input/input1
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:10.1-2
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
input: USB Keyboard as /class/input/input2
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:10.1-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
ata3.00: ATA-7: SAMSUNG HD160JJ, ZM100-41, max UDMA7
ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata4: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD160JJ ZM10 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: unknown partition table
sd 2:0:0:0: [sda] Attached SCSI disk
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input3
agpgart: Detected VIA P4M890 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'parport_pc'
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:04:01.0 to 64
Adding 979924k swap on /dev/hdb5. Priority:-1 extents:1 across:979924k
EXT3 FS on hdb2, internal journal
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
hda-intel: Invalid position buffer, using LPIB read method instead.
hald-addon-acpi[3193]: segfault at 0000000000000000 rip 00002b1ba7a6a61b rsp 00007fff03730250 error 4
** Loaded modules:
Module Size Used by
ipv6 296840 14
ppdev 13704 0
lp 17352 0
button 13472 0
ac 10376 0
battery 15496 0
loop 23044 0
snd_hda_intel 311968 3
snd_pcm_oss 48288 0
snd_mixer_oss 21376 1 snd_pcm_oss
snd_pcm 89992 3 snd_hda_intel,snd_pcm_oss
snd_timer 28424 2 snd_pcm
snd 65896 9 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 13088 1 snd
snd_page_alloc 14608 2 snd_hda_intel,snd_pcm
shpchp 38428 0
i2c_viapro 13848 0
i2c_core 31488 1 i2c_viapro
pci_hotplug 37252 1 shpchp
parport_pc 42664 1
parport 44428 3 ppdev,lp,parport_pc
via_agp 15872 1
psmouse 45468 0
serio_raw 11780 0
evdev 15232 5
tsdev 13312 0
pcspkr 7680 0
ext3 137232 5
jbd 68080 1 ext3
mbcache 13832 1 ext3
dm_mirror 26240 0
dm_snapshot 21320 0
dm_mod 64112 7 dm_mirror,dm_snapshot
sd_mod 33280 1
usbhid 32704 0
hid 31360 1 usbhid
ide_disk 21888 5
ide_cd 44832 0
cdrom 39848 1 ide_cd
sata_via 17540 2
floppy 67560 0
jmicron 8576 0 [permanent]
ahci 28804 0
ehci_hcd 37900 0
via_rhine 30344 0
mii 10240 1 via_rhine
uhci_hcd 29856 0
ata_generic 13188 0
libata 132016 3 sata_via,ahci,ata_generic
scsi_mod 164536 2 sd_mod,libata
via82cxxx 13572 0 [permanent]
generic 10372 0 [permanent]
ide_core 147728 5 ide_disk,ide_cd,jmicron,via82cxxx,generic
thermal 19600 0
processor 39784 1 thermal
fan 9992 0
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. P4M890 Host Bridge [1106:0327]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ce]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=128M]
Capabilities: <access denied>
00:00.1 Host bridge [0600]: VIA Technologies, Inc. P4M890 Host Bridge [1106:1327]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. P4M890 Host Bridge [1106:2327]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. P4M890 Host Bridge [1106:3327]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.4 Host bridge [0600]: VIA Technologies, Inc. P4M890 Host Bridge [1106:4327]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.5 PIC [0800]: VIA Technologies, Inc. P4M890 I/O APIC Interrupt Controller [1106:5327] (prog-if 20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
00:00.6 Host bridge [0600]: VIA Technologies, Inc. P4M890 Security Device [1106:6327]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
00:00.7 Host bridge [0600]: VIA Technologies, Inc. P4M890 Host Bridge [1106:7327]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dd000000-deffffff
Prefetchable memory behind bridge: a0000000-bfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:03.0 PCI bridge [0604]: VIA Technologies, Inc. P4M890 PCI to PCI Bridge Controller [1106:c327] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000cfff
Memory behind bridge: dfe00000-dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VT8237A SATA 2-Port Controller [1106:0591] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81cf]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at fc00 [size=8]
Region 1: I/O ports at f800 [size=4]
Region 2: I/O ports at f400 [size=8]
Region 3: I/O ports at f000 [size=4]
Region 4: I/O ports at ec00 [size=16]
Region 5: I/O ports at e800 [size=256]
Capabilities: <access denied>
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 07) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81cf]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at e400 [size=16]
Capabilities: <access denied>
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at dc00 [size=32]
Capabilities: <access denied>
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: <access denied>
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Capabilities: <access denied>
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at dffff000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237A PCI to ISA Bridge [1106:3337]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81cf]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: <access denied>
00:11.7 Host bridge [0600]: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
Subsystem: VIA Technologies, Inc. Unknown device [1106:337e]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Capabilities: <access denied>
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 7c)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:086c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at dfffe000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:13.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237A Host Bridge [1106:337b] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory behind bridge: dfd00000-dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. Unknown device [1106:3343] (rev 01) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ce]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=512M]
Region 1: Memory at dd000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at de000000 [disabled] [size=64K]
Capabilities: <access denied>
03:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 5: Memory at dfefe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at dfee0000 [disabled] [size=64K]
Capabilities: <access denied>
03:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 29
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c400 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at bc00 [size=16]
Capabilities: <access denied>
04:01.0 Audio device [0403]: VIA Technologies, Inc. VIA High Definition Audio Controller [1106:3288] (rev 10)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81b3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at dfdfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.22-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=UTF-8) (ignored: LC_ALL set to en_US.UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-2-amd64 depends on:
ii e2fsprogs 1.40.2-1 ext2 file system utilities and lib
ii initramfs-tools [linux-initr 0.91a tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.22-2-amd64 recommends no packages.
-- debconf information:
linux-image-2.6.22-2-amd64/preinst/initrd-2.6.22-2-amd64:
linux-image-2.6.22-2-amd64/preinst/already-running-this-2.6.22-2-amd64:
linux-image-2.6.22-2-amd64/preinst/bootloader-initrd-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.22-2-amd64/prerm/removing-running-kernel-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/preinst/abort-install-2.6.22-2-amd64:
linux-image-2.6.22-2-amd64/postinst/bootloader-test-error-2.6.22-2-amd64:
linux-image-2.6.22-2-amd64/preinst/lilo-initrd-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/preinst/failed-to-move-modules-2.6.22-2-amd64:
linux-image-2.6.22-2-amd64/postinst/depmod-error-2.6.22-2-amd64: false
linux-image-2.6.22-2-amd64/preinst/abort-overwrite-2.6.22-2-amd64:
linux-image-2.6.22-2-amd64/postinst/bootloader-error-2.6.22-2-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-2-amd64/prerm/would-invalidate-boot-loader-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/postinst/old-system-map-link-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/postinst/old-initrd-link-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/preinst/elilo-initrd-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.22-2-amd64/postinst/old-dir-initrd-link-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/postinst/depmod-error-initrd-2.6.22-2-amd64: false
linux-image-2.6.22-2-amd64/preinst/overwriting-modules-2.6.22-2-amd64: true
linux-image-2.6.22-2-amd64/postinst/create-kimage-link-2.6.22-2-amd64: true
Reply to: