Package: linux-image-2.6.21-1-686
Version: 2.6.21-3
Severity: normal
root@kodama:/home/joey>insmod /lib/modules/2.6.21-1-686/kernel/drivers/ide/legacy/ide-cs.ko
zsh: segmentation fault insmod /lib/modules/2.6.21-1-686/kernel/drivers/ide/legacy/ide-cs.ko
I can reproduce this on multiple laptops. Nothing in dmesg. Here's the end of a
strace of that:
read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\0`\1\000"..., 512) = 512
fstat64(3, {st_mode=S_IFREG|0644, st_size=1315328, ...}) = 0
mmap2(NULL, 1320356, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xb7e01000
mmap2(0xb7f3e000, 12288, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x13d) = 0xb7f3e000
mmap2(0xb7f41000, 9636, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xb7f41000
close(3) = 0
mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb7e00000
set_thread_area({entry_number:-1 -> 6, base_addr:0xb7e006c0, limit:1048575, seg_32bit:1, contents:0, read_exec_only:0, limit_in_pages:1, seg_not_present:0, useable:1}) = 0
mprotect(0xb7f3e000, 4096, PROT_READ) = 0
munmap(0xb7f44000, 109184) = 0
brk(0) = 0x804b000
brk(0x806c000) = 0x806c000
--- SIGSEGV (Segmentation fault) @ 0 (0) ---
+++ killed by SIGSEGV +++
Process 2187 detached
-- Package-specific info:
** Version: Linux version 2.6.21-1-686 (Debian 2.6.21-2) (waldi@debian.org) (gcc version 4.1.3 20070514 (prerelease) (Debian 4.1.2-7)) #1 SMP Sat May 19 01:13:28 UTC 2007
** Not tainted
** Kernel log:
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
usb usb4: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1e.0 at offset f (was 40000, writing 400ff)
PM: Writing back config space on device 0000:00:1e.0 at offset 9 (was 10001, writing 33f13001)
PM: Writing back config space on device 0000:00:1e.0 at offset 8 (was 0, writing b010b010)
PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was 22800000, writing 22802020)
PM: Writing back config space on device 0000:00:1e.0 at offset 6 (was 20070600, writing 200a0600)
PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100004, writing 100107)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ipw2200: Unable to load ucode: -22
ipw2200: Unable to load firmware: -22
ipw2200: Failed to up device
ahci 0000:00:1f.2: PORTS_IMPL is zero, forcing 0xf
PM: Writing back config space on device 0000:06:03.0 at offset f (was 7000100, writing 580010b)
PM: Writing back config space on device 0000:06:03.0 at offset e (was 0, writing 28fc)
PM: Writing back config space on device 0000:06:03.0 at offset d (was 0, writing 2800)
PM: Writing back config space on device 0000:06:03.0 at offset c (was 0, writing 24fc)
PM: Writing back config space on device 0000:06:03.0 at offset b (was 0, writing 2400)
PM: Writing back config space on device 0000:06:03.0 at offset a (was 0, writing 3bfff000)
PM: Writing back config space on device 0000:06:03.0 at offset 9 (was 0, writing 38000000)
PM: Writing back config space on device 0000:06:03.0 at offset 8 (was 0, writing 33fff000)
PM: Writing back config space on device 0000:06:03.0 at offset 7 (was 0, writing 30000000)
PM: Writing back config space on device 0000:06:03.0 at offset 6 (was 0, writing b00a0706)
PM: Writing back config space on device 0000:06:03.0 at offset 4 (was 0, writing b0103000)
PM: Writing back config space on device 0000:06:03.0 at offset 3 (was 820000, writing 82a800)
PM: Writing back config space on device 0000:06:03.0 at offset 1 (was 2100000, writing 2100007)
PM: Writing back config space on device 0000:06:03.1 at offset 4 (was 0, writing b0100000)
PM: Writing back config space on device 0000:06:03.1 at offset 3 (was 800000, writing 802000)
PM: Writing back config space on device 0000:06:03.1 at offset 1 (was 2100000, writing 2100106)
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[b0100000-b01007ff] Max Packet=[2048] IR/IT contexts=[4/4]
PM: Writing back config space on device 0000:06:03.2 at offset 4 (was 0, writing b0100800)
PM: Writing back config space on device 0000:06:03.2 at offset 3 (was 800000, writing 802000)
PM: Writing back config space on device 0000:06:03.2 at offset 1 (was 2100000, writing 2100106)
ACPI: PCI Interrupt 0000:06:03.2[A] -> GSI 16 (level, low) -> IRQ 16
PM: Writing back config space on device 0000:06:03.3 at offset 4 (was 0, writing b0100c00)
PM: Writing back config space on device 0000:06:03.3 at offset 1 (was 2100000, writing 2100102)
PM: Writing back config space on device 0000:06:03.4 at offset 4 (was 0, writing b0101000)
PM: Writing back config space on device 0000:06:03.4 at offset 1 (was 2100000, writing 2100102)
PM: Writing back config space on device 0000:06:04.0 at offset 5 (was 0, writing b0101400)
PM: Writing back config space on device 0000:06:04.0 at offset 4 (was 1, writing 2001)
PM: Writing back config space on device 0000:06:04.0 at offset 3 (was 0, writing 2000)
PM: Writing back config space on device 0000:06:04.0 at offset 1 (was 2900000, writing 2900107)
eth0: link down
wlan0: Coming out of suspend...
PCI: Enabling device 0000:06:05.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 18 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:06:05.0 at offset f (was 18030100, writing 1803010b)
PM: Writing back config space on device 0000:06:05.0 at offset 4 (was 0, writing b0102000)
PM: Writing back config space on device 0000:06:05.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:06:05.0 at offset 1 (was 2900002, writing 2900106)
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 0)
usbdev5.1_ep00: PM: resume from 0, parent usb5 still 2
usbdev5.1_ep81: PM: resume from 0, parent 5-0:1.0 still 2
usbdev5.1: PM: resume from 0, parent usb5 still 2
usbdev3.2_ep00: PM: resume from 0, parent 3-1 still 2
usbdev3.2_ep81: PM: resume from 0, parent 3-1:1.0 still 2
usbdev3.2_ep02: PM: resume from 0, parent 3-1:1.0 still 2
usbdev3.2: PM: resume from 0, parent 3-1 still 2
usbdev4.2_ep00: PM: resume from 0, parent 4-2 still 2
hci_usb 4-2:1.0: PM: resume from 2, parent 4-2 still 2
hci0: PM: resume from 0, parent 4-2:1.0 still 2
usbdev4.2_ep81: PM: resume from 0, parent 4-2:1.0 still 2
usbdev4.2_ep02: PM: resume from 0, parent 4-2:1.0 still 2
usbdev4.2_ep82: PM: resume from 0, parent 4-2:1.0 still 2
hci_usb 4-2:1.1: PM: resume from 2, parent 4-2 still 2
usbdev4.2_ep03: PM: resume from 0, parent 4-2:1.1 still 2
usbdev4.2_ep83: PM: resume from 0, parent 4-2:1.1 still 2
usb 4-2:1.2: PM: resume from 2, parent 4-2 still 2
usbdev4.2: PM: resume from 0, parent 4-2 still 2
Restarting tasks ... <6>usb 3-1: USB disconnect, address 2
usb 4-2: USB disconnect, address 2
done.
ata1: waiting for device to spin up (8 secs)
usb 3-1: new full speed USB device using uhci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
usb 4-2: new full speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
tun1: Disabled Privacy Extensions
hda_intel: azx_get_response timeout, switching to single_cmd mode...
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xb0100000-0xb01fffff: excluding 0xb0100000-0xb010ffff
pcmcia: registering new device pcmcia0.0
pccard: card ejected from slot 0
pccard: PCMCIA card inserted into slot 0
pccard: card ejected from slot 0
pccard: PCMCIA card inserted into slot 0
pccard: card ejected from slot 0
pccard: PCMCIA card inserted into slot 0
** Loaded modules:
Module Size Used by
ide_cs 10080 0
sd_mod 19904 0
pl2303 19396 0
usbserial 31528 1 pl2303
uhci_hcd 22608 0
snd_rtctimer 3520 0
sdhci 16652 0
ipw2200 130628 0
hci_usb 16220 0
i915 21280 2
drm 73908 3 i915
binfmt_misc 10984 1
rfcomm 35480 0
l2cap 22208 3 rfcomm
nfsd 202800 17
exportfs 5472 1 nfsd
ppdev 8580 0
parport_pc 32740 0
lp 10884 0
parport 33672 3 ppdev,parport_pc,lp
button 7952 0
ac 5220 0
battery 10020 0
tun 10304 2
ipv6 236192 30
nfs 222444 5
lockd 58248 3 nfsd,nfs
nfs_acl 3520 2 nfsd,nfs
sunrpc 154972 13 nfsd,nfs,lockd,nfs_acl
fuse 41684 1
video 16488 0
usb_storage 76384 0
cpufreq_userspace 4128 1
cpufreq_ondemand 7884 0
speedstep_centrino 9220 1
freq_table 4512 2 cpufreq_ondemand,speedstep_centrino
sbp2 21188 0
ide_generic 1344 0 [permanent]
ide_cd 36512 0
joydev 9152 0
tsdev 7520 0
snd_hda_intel 20248 5
snd_hda_codec 198336 1 snd_hda_intel
snd_pcm_oss 39168 0
snd_pcm 71940 5 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_mixer_oss 15328 1 snd_pcm_oss
snd_seq_dummy 3748 0
snd_seq_oss 29248 0
pcmcia 35276 1 ide_cs
snd_seq_midi 8160 0
snd_rawmidi 22400 1 snd_seq_midi
ieee80211 30984 1 ipw2200
ieee80211_crypt 5792 1 ieee80211
pcspkr 3136 0
psmouse 34952 0
rtc 12760 1 snd_rtctimer
snd_seq_midi_event 6880 2 snd_seq_oss,snd_seq_midi
mmc_core 26340 1 sdhci
serio_raw 6564 0
firmware_class 9408 2 ipw2200,pcmcia
i2c_i801 8560 0
yenta_socket 24876 2
rsrc_nonstatic 11968 1 yenta_socket
pcmcia_core 36884 4 ide_cs,pcmcia,yenta_socket,rsrc_nonstatic
snd_seq 46160 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 20868 3 snd_rtctimer,snd_pcm,snd_seq
snd_seq_device 7596 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
i2c_core 20480 1 i2c_i801
snd 48132 18 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
iTCO_wdt 9956 0
bluetooth 48484 3 hci_usb,rfcomm,l2cap
intel_agp 23004 1
agpgart 32168 3 drm,intel_agp
evdev 9216 5
eth1394 18276 0
soundcore 7424 1 snd
snd_page_alloc 9512 2 snd_hda_intel,snd_pcm
ext3 120904 1
jbd 55208 1 ext3
mbcache 8164 1 ext3
dm_mirror 20116 0
dm_snapshot 16420 0
dm_mod 52556 2 dm_mirror,dm_snapshot
sg 32476 0
sr_mod 16100 0
cdrom 32768 2 ide_cd,sr_mod
ata_piix 13508 0
ide_disk 15648 3
ahci 19940 0
ata_generic 8100 0
libata 109108 3 ata_piix,ahci,ata_generic
scsi_mod 133740 6 sd_mod,usb_storage,sbp2,sg,sr_mod,libata
piix 9508 0 [permanent]
8139too 25536 0
generic 4804 0 [permanent]
ide_core 115016 7 ide_cs,usb_storage,ide_generic,ide_cd,ide_disk,piix,generic
8139cp 22336 0
mii 5280 2 8139too,8139cp
ohci1394 32432 0
ieee1394 89560 3 sbp2,eth1394,ohci1394
ehci_hcd 30796 0
usbcore 123304 7 pl2303,usbserial,uhci_hcd,hci_usb,usb_storage,ehci_hcd
thermal 14120 0
processor 30888 2 speedstep_centrino,thermal
fan 4868 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 04)
Subsystem: Fujitsu Limited. Unknown device [10cf:12d7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 04) (prog-if 00 [VGA])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1400 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at b0040000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 04)
Subsystem: Fujitsu Limited. Unknown device [10cf:12e2]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at 34000000 (32-bit, non-prefetchable) [disabled] [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller [8086:2668] (rev 04)
Subsystem: Fujitsu Limited. Unknown device [10cf:1326]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 04) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at 1420 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 04) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 1440 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 04) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 1460 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 04) (prog-if 00 [UHCI])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1480 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 04) (prog-if 20 [EHCI])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at b0004000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=0a, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: b0100000-b01fffff
Prefetchable memory behind bridge: 0000000030000000-0000000033ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 04)
Subsystem: Fujitsu Limited. Unknown device [10cf:12e4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller [8086:266f] (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e5]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1410 [size=16]
00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 04) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Fujitsu Limited. Unknown device [10cf:12e6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 14b8 [size=8]
Region 1: I/O ports at 140c [size=4]
Region 2: I/O ports at 14b0 [size=8]
Region 3: I/O ports at 1408 [size=4]
Region 4: I/O ports at 14a0 [size=16]
Region 5: Memory at b0004400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 04)
Subsystem: Fujitsu Limited. Unknown device [10cf:12e7]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 14c0 [size=32]
06:03.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b3)
Subsystem: Fujitsu Limited. Unknown device [10cf:1254]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0103000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 30000000-33fff000 (prefetchable)
Memory window 1: 38000000-3bfff000
I/O window 0: 00002400-000024ff
I/O window 1: 00002800-000028ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
06:03.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] (rev 08) (prog-if 10 [OHCI])
Subsystem: Fujitsu Limited. Unknown device [10cf:1255]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at b0100000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
06:03.2 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 17)
Subsystem: Fujitsu Limited. Unknown device [10cf:1323]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0100800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
06:03.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 08)
Subsystem: Fujitsu Limited. Unknown device [10cf:1257]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0100c00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
06:03.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 03)
Subsystem: Fujitsu Limited. Unknown device [10cf:1324]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0101000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
06:04.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Fujitsu Limited. Unknown device [10cf:12ce]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at b0101400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
06:05.0 Network controller [0280]: Intel Corporation PRO/Wireless 2915ABG Network Connection [8086:4223] (rev 05)
Subsystem: Intel Corporation Unknown device [8086:1030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b0102000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.21-1-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.21-1-686 depends on:
ii initramfs-tools [linux-initr 0.88 tools for generating an initramfs
ii module-init-tools 3.3-pre11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.21-1-686 recommends:
ii libc6-i686 2.5-9 GNU C Library: Shared libraries [i
-- debconf information excluded
--
see shy jo
Attachment:
signature.asc
Description: Digital signature