Bug#412718: linux-2.6: linux-image-2.6.18-4-486 does not start on IBM Blade 883221X (ACPI?)
Package: linux-2.6
Severity: normal
Hi,
trying out the Etch installer I found that linux-image-2.6.18-4-486 does
not start on an IBM Blade server 883221X. Here is the output:
Linux version 2.6.18-4-486 (Debian 2.6.18.dfsg.1-11) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Wed Feb 21 15:25:16 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffed040 (usable)
BIOS-e820: 000000003ffed040 - 000000003fff0000 (ACPI data)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 0009e140
DMI 2.3 present.
ACPI: PM-Timer IO Port: 0x488
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled)
Processor #6 15:2 APIC version 20
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled)
Processor #7 15:2 APIC version 20
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 14, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x0d] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 13, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x0c] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 12, version 17, address 0xfec02000, GSI 32-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Enabling APIC mode: Flat. Using 3 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 2799.483 MHz processor.
Built 1 zonelists. Total pages: 229376
Kernel command line: vga=normal initrd=debian-installer/i386/initrd.gz -- console=ttyS0,19200 BOOT_IMAGE=debian-installer/i386/linux
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 902088k/917504k available (1502k kernel code, 14808k reserved, 601k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5601.83 BogoMIPS (lpj=11203674)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 4225k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd82c, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
ACPI: PCI Root Bridge [PCI1] (0000:02)
ACPI: PCI Root Bridge [PCI2] (0000:01)
ACPI: PCI Interrupt Link [LPUS] (IRQs *7)
ACPI: PCI Interrupt Link [LPID] (IRQs *14)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x510-0x517 could not be reserved
pnp: 00:01: ioport range 0x504-0x507 could not be reserved
pnp: 00:01: ioport range 0x500-0x503 could not be reserved
pnp: 00:01: ioport range 0x420-0x427 has been reserved
pnp: 00:01: ioport range 0x460-0x461 has been reserved
pnp: 00:08: ioport range 0x1ec-0x1ef has been reserved
pnp: 00:08: ioport range 0x400-0x4fe could not be reserved
pnp: 00:08: ioport range 0x600-0x600 has been reserved
pnp: 00:08: ioport range 0x800-0x80f has been reserved
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1172598244.012:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
S0 S4 S5)
Freeing unused kernel memory: 256k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LPUS] enabled at IRQ 7
ACPI: PCI Interrupt 0000:00:0f.2[A] -> Link [LPUS] -> GSI 7 (level, low) -> IRQ 7
ohci_hcd 0000:00:0f.2: OHCI Host Controller
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0f.2: irq 7, io mem 0xfebfe000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
tg3.c:v3.65 (August 07, 2006)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth0: Tigon3 [partno(BCM95704A41) rev 2002 PHY(serdes)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:60:9c:3b:bc
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[0] TSOcap[0]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:01:00.1[B] -> GSI 17 (level, low) -> IRQ 177
eth1: Tigon3 [partno(BCM95704A41) rev 2002 PHY(serdes)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:60:9c:3b:bd
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
ACPI: Getting cpuindex for acpiid 0x2
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Getting cpuindex for acpiid 0x0
-- System Information:
Debian Release: 3.1
APT prefers unstable
APT policy: (50, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.12-1-k7
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Reply to: