Bug#398645: linux-image-2.6.18-2: invalid argument for /sys/power/state
Package: linux-image-2.6.18-2
Severity: important
I have an IBM/Lenovo x60s. Under the stock 2.6.17 kernels, I can
suspend my machine (to disk and ram), while under any of the stock
2.6.18 kernels, the process fails.
To wit, this is what happens when I try to manually suspend the
machine (normally I use the hibernate package).
%echo -n mem > /sys/power/state
bash: echo: write error: Invalid argument
(Yes, it leaves all of those lines on the prompt.)
dmesg output is below. The most interesting errors seem to be:
Class driver suspend failed for cpu0
Could not power down device ��������� error -22
Some devices failed to power down
On a related note, it seems that the 2.6.18 kernels can no longer load
the speedstep-centrino modules on my machine:
%modprobe -v speedstep-centrino
insmod /lib/modules/2.6.18-2-686/kernel/arch/i386/kernel/cpu/cpufreq/speedstep-centrino.ko
FATAL: Error inserting speedstep_centrino (/lib/modules/2.6.18-2-686/kernel/arch/i386/kernel/cpu/cpufreq/speedstep-centrino.ko):
Device or resource busy
This also worked fine under any of the 2.6.17 kernels.
��ustin
-- System Information:
Debian Release: testing/unstable
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.18-2-686
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
-- dmesg input:
ling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 70000000 (gap: 60000000:90000000)
Detected 1662.691 MHz processor.
Built 1 zonelists. Total pages: 390880
Kernel command line: root=/dev/sda1 ro acpi_sleep=s3_bios
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1542120k/1563520k available (1543k kernel code, 20128k reserved, 574k data, 196k init, 646016k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Calibrating delay using timer specific routine.. 3329.19 BogoMIPS (lpj=6658392)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) CPU L2400 @ 1.66GHz stepping 08
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.17 BogoMIPS (lpj=6650356)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU L2400 @ 1.66GHz stepping 08
Total of 2 processors activated (6654.37 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs:
CPU#0 had -171 usecs TSC skew, fixed it up.
CPU#1 had 171 usecs TSC skew, fixed it up.
Brought up 2 CPUs
migration_cost=41
checking if image is initramfs... it is
Freeing initrd memory: 4385k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 28) interrupt mode.
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: 2000-2fff
MEM window: ee000000-ee0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: 3000-4fff
MEM window: ec000000-edffffff
PREFETCH window: e4000000-e40fffff
PCI: Bridge: 0000:00:1c.2
IO window: 5000-6fff
MEM window: e8000000-e9ffffff
PREFETCH window: e4100000-e41fffff
PCI: Bridge: 0000:00:1c.3
IO window: 7000-8fff
MEM window: ea000000-ebffffff
PREFETCH window: e4200000-e42fffff
PCI: Bus 22, cardbus bridge: 0000:15:00.0
IO window: 00009000-000090ff
IO window: 00009400-000094ff
PREFETCH window: e0000000-e1ffffff
MEM window: e6000000-e7ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 9000-cfff
MEM window: e4300000-e7ffffff
PREFETCH window: e0000000-e3ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1e.0 (0005 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:15:00.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Simple Boot Flag at 0x35 set to 0x1
audit: initializing netlink socket (disabled)
audit(1163527717.328:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (33 C)
ACPI: Thermal Zone [THM1] (34 C)
Time: hpet clocksource has been installed.
ieee1394: Initialized config rom entry `ip1394'
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:02:00.0 to 64
usbcore: registered new driver usbfs
usbcore: registered new driver hub
e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:16:d3:22:0c:87
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
USB Universal Host Controller Interface driver v3.0
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 201, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 58, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 66, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 74, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:15:00.1[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:15:00.1 to 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[58] MMIO=[e4301000-e43017ff] Max Packet=[2048] IR/IT contexts=[4/4]
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18B0 irq 14
scsi0 : ata_piix
usb 4-2: new full speed USB device using uhci_hcd and address 2
ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
Vendor: ATA Model: HTS541080G9SA00 Rev: MB4I
Type: Direct-Access ANSI SCSI revision: 05
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18B8 irq 15
scsi1 : ata_piix
usb 4-2: configuration #1 chosen from 1 choice
ATA: abnormal status 0x7F on port 0x177
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 74, io mem 0xee444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
usb 4-2: USB disconnect, address 2
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 4-2: new full speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae4060017202e]
irda_init()
NET: Registered protocol family 23
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input1
Yenta: CardBus bridge found at 0000:15:00.0 [17aa:201c]
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Linux agpgart interface v0.101 (c) Dave Jones
intel_rng: FWH not detected
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.1.0d
ipw3945: Copyright(c) 2003-2006 Intel Corporation
Yenta: ISA IRQ mask 0x0cb8, PCI irq 201
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x9000 - 0xcfff
cs: IO port probe 0x9000-0xcfff: clean.
pcmcia: parent PCI bridge Memory window: 0xe4300000 - 0xe7ffffff
pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe3ffffff
sdhci: SDHCI controller found at 0000:15:00.2 [1180:0822] (rev 18)
ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:15:00.2 to 64
mmc0: SDHCI at 0xe4301800 irq 66 DMA
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:03:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
ACPI: PCI Interrupt 0000:00:1f.3[A] -> GSI 23 (level, low) -> IRQ 193
ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1b.0 to 64
cs: IO port probe 0x100-0x3af: excluding 0x370-0x377
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input2
pnp: Device 00:0a activated.
nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x164e
nsc-ircc, driver loaded (Dag Brattli)
IrDA: Registered device irda0
nsc-ircc, Found dongle: No dongle connected
nsc_ircc_init_dongle_interface(), No dongle connected
ts: Compaq touchscreen protocol output
Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k
EXT3 FS on sda1, internal journal
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (off-line)
ibm_acpi: IBM ThinkPad ACPI Extras v0.12a
ibm_acpi: http://ibm-acpi.sf.net/
tp_base: tp_base 0.22 loaded.
tp_smapi: tp_smapi 0.22 loading...
tp_smapi: successfully loaded (smapi_port=0xb2).
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
ipw3945: Detected geography ABG (11 802.11bg channels, 13 802.11a channels)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
apm: BIOS not found.
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6 over IPv4 tunneling driver
Non-volatile memory driver v1.2
input: /usr/sbin/thinkpad-keys as /class/input/input3
tp_smapi: battery 0: changed start threshold to 39(+1)
tp_smapi: battery 0: changed stop threshold to 70
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 201
[drm] Initialized i915 1.5.0 20060119 on minor 0
wlan0: no IPv6 routers present
wlan0: no IPv6 routers present
Freezing cpus ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Stopping tasks: ==================================================================================================================|
usbdev4.3_ep83: PM: suspend 0->2, parent 4-2:1.0 already 1
usbdev4.3_ep02: PM: suspend 0->2, parent 4-2:1.0 already 1
usbdev4.3_ep81: PM: suspend 0->2, parent 4-2:1.0 already 1
pnp: Device 00:0a disabled.
ACPI: PCI interrupt for device 0000:15:00.2 disabled
ACPI: PCI interrupt for device 0000:15:00.0 disabled
wlan0: Going into suspend...
ACPI: PCI interrupt for device 0000:03:00.0 disabled
ACPI: PCI interrupt for device 0000:02:00.0 disabled
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Class driver suspend failed for cpu0
Could not power down device ��������� error -22
Some devices failed to power down
PCI: Enabling device 0000:00:1b.0 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1b.0 to 64
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1d.0 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.1 to 64
PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.2 to 64
PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.3 to 64
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 400, writing 40b)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing ee444000)
PM: Writing back config space on device 0000:00:1d.7 at offset 1 (was 2900006, writing 2900106)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.2 at offset 1 (was 2b80000, writing 2b80005)
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:02:00.0 to 64
wlan0: Coming out of suspend...
PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 58
PM: Writing back config space on device 0000:03:00.0 at offset f (was 100, writing 10b)
PM: Writing back config space on device 0000:03:00.0 at offset 4 (was 0, writing edf00000)
PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100002, writing 100106)
PM: Writing back config space on device 0000:15:00.0 at offset 1 (was 2100000, writing 2100007)
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 201
PM: Writing back config space on device 0000:15:00.2 at offset 4 (was 0, writing e4301800)
PM: Writing back config space on device 0000:15:00.2 at offset 3 (was 800000, writing 804000)
PM: Writing back config space on device 0000:15:00.2 at offset 1 (was 2100000, writing 2100006)
ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) -> IRQ 66
ATA: abnormal status 0x7F on port 0x177
pnp: Device 00:08 does not support activation.
pnp: Device 00:09 does not support activation.
pnp: Device 00:0a activated.
usbdev4.3_ep81: PM: resume from 0, parent 4-2:1.0 still 1
usbdev4.3_ep02: PM: resume from 0, parent 4-2:1.0 still 1
usbdev4.3_ep83: PM: resume from 0, parent 4-2:1.0 still 1
nsc_ircc_init_dongle_interface(), No dongle connected
nsc_ircc_change_dongle_speed(), No dongle connected is not for IrDA mode
tp_smapi: battery 0: changed stop threshold to 70
tp_smapi: battery 0: changed start threshold to 39(+1)
tp_smapi: battery 1: changed stop threshold to 0
tp_smapi: battery 1: changed start threshold to 0(+1)
Restarting tasks...<6>usb 4-2: USB disconnect, address 3
done
Thawing cpus ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.17 BogoMIPS (lpj=6650343)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU L2400 @ 1.66GHz stepping 08
CPU1 is up
usb 4-2: new full speed USB device using uhci_hcd and address 4
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
usb 4-2: configuration #1 chosen from 1 choice
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input4
ata1.00: configured for UDMA/100
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
ipw3945: Detected geography ABG (11 802.11bg channels, 13 802.11a channels)
Freezing cpus ...
Breaking affinity for irq 0
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Stopping tasks: ===============================================================================================================|
usbdev4.4_ep83: PM: suspend 0->2, parent 4-2:1.0 already 1
usbdev4.4_ep02: PM: suspend 0->2, parent 4-2:1.0 already 1
usbdev4.4_ep81: PM: suspend 0->2, parent 4-2:1.0 already 1
pnp: Device 00:0a disabled.
ACPI: PCI interrupt for device 0000:15:00.2 disabled
ACPI: PCI interrupt for device 0000:15:00.0 disabled
wlan0: Going into suspend...
ACPI: PCI interrupt for device 0000:03:00.0 disabled
ACPI: PCI interrupt for device 0000:02:00.0 disabled
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Class driver suspend failed for cpu0
Could not power down device ��������� error -22
Some devices failed to power down
PCI: Enabling device 0000:00:1b.0 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1b.0 to 64
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1d.0 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.1 to 64
PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.2 to 64
PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.3 to 64
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 400, writing 40b)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing ee444000)
PM: Writing back config space on device 0000:00:1d.7 at offset 1 (was 2900006, writing 2900106)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.2 at offset 1 (was 2b80000, writing 2b80005)
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:02:00.0 to 64
wlan0: Coming out of suspend...
PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 58
PM: Writing back config space on device 0000:03:00.0 at offset f (was 100, writing 10b)
PM: Writing back config space on device 0000:03:00.0 at offset 4 (was 0, writing edf00000)
PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100002, writing 100106)
PM: Writing back config space on device 0000:15:00.0 at offset 1 (was 2100000, writing 2100007)
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 201
PM: Writing back config space on device 0000:15:00.2 at offset 4 (was 0, writing e4301800)
PM: Writing back config space on device 0000:15:00.2 at offset 3 (was 800000, writing 804000)
PM: Writing back config space on device 0000:15:00.2 at offset 1 (was 2100000, writing 2100006)
ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) -> IRQ 66
ATA: abnormal status 0x7F on port 0x177
pnp: Device 00:08 does not support activation.
pnp: Device 00:09 does not support activation.
pnp: Device 00:0a activated.
nsc_ircc_init_dongle_interface(), No dongle connected
nsc_ircc_change_dongle_speed(), No dongle connected is not for IrDA mode
tp_smapi: battery 0: changed stop threshold to 70
tp_smapi: battery 0: changed start threshold to 39(+1)
tp_smapi: battery 1: changed stop threshold to 0
tp_smapi: battery 1: changed start threshold to 0(+1)
usbdev4.4_ep81: PM: resume from 0, parent 4-2:1.0 still 1
usbdev4.4_ep02: PM: resume from 0, parent 4-2:1.0 still 1
usbdev4.4_ep83: PM: resume from 0, parent 4-2:1.0 still 1
Restarting tasks...<6>usb 4-2: USB disconnect, address 4
done
Thawing cpus ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.10 BogoMIPS (lpj=6650215)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU L2400 @ 1.66GHz stepping 08
CPU1 is up
usb 4-2: new full speed USB device using uhci_hcd and address 5
usb 4-2: configuration #1 chosen from 1 choice
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input5
ata1.00: configured for UDMA/100
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
ipw3945: Detected geography ABG (11 802.11bg channels, 13 802.11a channels)
Reply to: