Bug#386972: Network failure on upgrade to 2.6.16
tags 386972 -moreinfo
clone 386972 -1
reassign -1 linux-image-2.6.17-2-686
retitle -1 Network failure on upgrade to 2.6.17
thanks
[Sorry about the duplicate, forgot to copy the bug and control.]
On Mon, 2006-09-11 at 15:02 +0200, maximilian attems wrote:
> severity 386972 important
> tags 386972 moreinfo
> stop
>
> On Mon, Sep 11, 2006 at 07:50:14AM -0400, Adam C Powell IV wrote:
> > Package: linux-image-2.6.16-2-686-smp
> > Version: 2.6.16-18
> > Severity: grave
> > Justification: causes debilitating loss of functionality
>
> an DD should no not to escalate severity,
> driver failures are important.
> also you are using an older kernel that is not targeted for
> the etch release, please try with 2.6.17.
Sorry about the inappropriate severity. (Not sure what you mean by
"escalate" but will use important in the future.)
Cloning this bug to deal with 2.6.17 as well.
[snip]
> > Greetings,
> >
> > I just upgraded a machine from sarge to etch, and in the process
> > upgraded from 2.6.8 to 2.6.16. When I rebooted, and on multiple reboots
> > since, the network has been completely non-functional. The kernel seems
> > to sense the wire, but is unable to send or receive packets.
> >
> > The machine has two interfaces: an Intel Ethernet Pro 100 and Realtek
> > 8139 compatible. On boot, it loads e100, 8139cp and
> > 8139too. /etc/modules does not have any network modules (needs eepro100
> > for 2.6.8, but I removed it, no change). The relevant lspci listings
> > are:
> >
> > 00:09.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 05)
> > 00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> >
> > lspci -v shows that the RTL8139 shares IRQ 10 with the USB controller
> > (Intel 82371AB/EB/MB PIIX4), and the eepro100 shares IRQ 11 with the
> > video card (Voodoo 3).
> >
> > Trying to configure the network:
> >
> > e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
> > then the usual DHCP messages, with DHCPDISCOVER repeated to failure.
> >
> > "dmesg | grep eth" gives:
> >
> > eth0: RealTek RTL8139 at 0xe800, 00:40:f4:15:2d:e5, IRQ 10
> > eth0: Identified 8139 chip type 'RTL-8139C'
> > e100: eth1: e100_probe: addr 0xeb100000, irq 11, MAC addr 00:00:AC:A6:0B:DD
> > e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
> > eth1: link down
> > ADDRCONF(NETDEV_UP): eth1: link is not ready
> > eth0: no IPv6 routers present
> > eth0: no IPv6 routers present
> >
> > DHCP also fails on eth1. With a static address, no packets get in or
> > out, on eth0 or eth1.
> >
> > [2.6.16 also hung twice in the course of working on this, console cursor
> > still blinking but the keyboard dead. 2.6.8 has never hung on me, under
> > sarge or etch.]
> >
> > Both interfaces still work perfectly with 2.6.8, but of course hotplug,
> > gamin, etc. don't...
> >
> > Please let me know what other information you need to try to resolve
> > this.
>
> lspci -v
> and the output of both kernels:
> cat /proc/interrupts
Attached.
Thanks,
-Adam
--
GPG fingerprint: D54D 1AEE B11C CE9B A02B C5DD 526F 01E8 564E E4B6
Welcome to the best software in the world today cafe!
http://www.take6.com/albums/greatesthits.html
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Flags: bus master, medium devsel, latency 64
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e4000000-e7ffffff
Prefetchable memory behind bridge: e8000000-e9ffffff
00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
Flags: bus master, medium devsel, latency 0
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Flags: bus master, medium devsel, latency 64
I/O ports at f000 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 64, IRQ 185
I/O ports at e000 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
Flags: medium devsel, IRQ 9
00:09.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 05)
Subsystem: IBM 82558B Ethernet Pro 10/100
Flags: bus master, medium devsel, latency 64, IRQ 177
Memory at eb100000 (32-bit, prefetchable) [size=4K]
I/O ports at e400 [size=32]
Memory at eb000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at ea000000 [disabled] [size=1M]
Capabilities: <access denied>
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 185
I/O ports at e800 [size=256]
Memory at eb101000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
01:00.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc. Voodoo3 AGP
Flags: 66MHz, fast devsel, IRQ 169
Memory at e4000000 (32-bit, non-prefetchable) [size=32M]
Memory at e8000000 (32-bit, prefetchable) [size=32M]
I/O ports at d000 [size=256]
Capabilities: <access denied>
CPU0 CPU1
0: 134203535 134206776 IO-APIC-edge timer
1: 14087 14344 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
3: 188122 192516 IO-APIC-edge serial
5: 1 3 IO-APIC-edge soundblaster
8: 2 2 IO-APIC-edge rtc
14: 231530 238419 IO-APIC-edge ide0
15: 6 7 IO-APIC-edge ide1
177: 3366847 18 IO-APIC-level eth0
NMI: 0 0
LOC: 268426967 268427022
ERR: 0
MIS: 0
CPU0 CPU1
0: 13011 23304 IO-APIC-edge timer
1: 68 55 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
5: 4 0 IO-APIC-edge soundblaster
7: 0 0 IO-APIC-edge parport0
8: 1 3 IO-APIC-edge rtc
9: 0 0 IO-APIC-edge acpi
10: 0 0 IO-APIC-edge uhci_hcd:usb1, eth1
11: 0 0 IO-APIC-edge eth0
14: 2582 2071 IO-APIC-edge ide0
15: 573 752 IO-APIC-edge ide1
NMI: 0 0
LOC: 36213 36219
ERR: 0
MIS: 0
CPU0 CPU1
0: 64396 38555 IO-APIC-edge timer
1: 654 670 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
5: 3 1 IO-APIC-edge soundblaster
7: 0 0 IO-APIC-edge parport0
8: 4 0 IO-APIC-edge rtc
9: 0 0 IO-APIC-edge acpi
10: 0 0 IO-APIC-edge uhci_hcd:usb1, eth1
11: 0 0 IO-APIC-edge eth0
14: 4416 1284 IO-APIC-edge ide0
15: 4175 3582 IO-APIC-edge ide1
NMI: 0 0
LOC: 102849 102854
ERR: 0
MIS: 0
Reply to: