Hi Maks,
I can confirm that removing floppy from /etc/initramfs-tools/modules (which
still causes a non-bootable system) and inserting cpqarray (which is the only
uncommented module in /etc/initramfs-tools/modules) does in fact allow the
system to boot.
I have attached the dmesg and lsmod.
Thanks again,
Joshua Rubin
Begin dmesg:
____________________________________
Linux version 2.6.16-2-686-smp (Debian 2.6.16-17) (waldi@debian.org) (gcc
version 4.0.4 20060630 (prerelease) (Debian 4.0.3-4)) #1 SMP Sat Jul 15
22:33:00 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fffc000 (usable)
BIOS-e820: 000000000fffc000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
found SMP MP-table at 000f4ff0
On node 0 totalpages: 65532
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 61436 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
ACPI: RSDP (v000 COMPAQ ) @ 0x000f4f90
ACPI: RSDT (v001 COMPAQ MICRO 0x00000002 � 0x0000162e) @ 0x0fffc000
ACPI: FADT (v001 COMPAQ MICRO 0x00000002 � 0x0000162e) @ 0x0fffc040
ACPI: MADT (v001 COMPAQ 00000083 0x00000002 0x00000000) @ 0x0fffc100
ACPI: SSDT (v001 COMPAQ SSDT 0x00000001 MSFT 0x0100000b) @ 0x0ffff800
ACPI: DSDT (v001 COMPAQ DSDT 0x00000001 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x240
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-34
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: root=/dev/ida/c0d0p1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 997.113 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 251936k/262128k available (1505k kernel code, 9532k reserved, 545k
data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2003.87 BogoMIPS
(lpj=4007752)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 06
Booting processor 1/0 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1993.85 BogoMIPS
(lpj=3987713)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 06
Total of 2 processors activated (3997.73 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=4000
checking if image is initramfs... it is
Freeing initrd memory: 4287k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0094, last bus=3
PCI: Using configuration type 1
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:03.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Root Bridge [PCI1] (0000:03)
PCI: Probing PCI hardware (bus 03)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Interrupt Link [FAKE] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [INA0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INA1] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR1] (IRQs 5 *10 11 15)
ACPI: PCI Interrupt Link [ITR2] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR3] (IRQs 5 10 11 15) *7
ACPI: PCI Interrupt Link [ITR4] (IRQs 5 10 *11 15)
ACPI: PCI Interrupt Link [INB0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB1] (IRQs 5 10 11 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Device 0000:00:00.0 not found by BIOS
PCI: Device 0000:00:00.1 not found by BIOS
PCI: Device 0000:00:0f.0 not found by BIOS
pnp: 00:01: ioport range 0xf50-0xf58 has been reserved
audit: initializing netlink socket (disabled)
audit(1155913049.052:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI wakeup devices:
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 176k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Compaq SMART2 Driver (v 2.6.0)
cpqarray: Device 0x10 has been found at bus 0 dev 1 func 0
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 177
cpqarray: Finding drives on ida0 (Integrated Array)
cpqarray ida/c0d0: blksz=512 nr_blks=17756160
cpqarray: Starting firmware's background processing
ida/c0d0: p1 p2 < p5 p6 p7 p8 p9 >
ACPI: Thermal Zone [THM0] (8 C)
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 17 (level, low) -> IRQ 185
e100: eth0: e100_probe: addr 0xc6fff000, irq 185, MAC addr 00:02:A5:8A:13:A8
ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 24 (level, low) -> IRQ 193
e100: eth1: e100_probe: addr 0xc6dff000, irq 193, MAC addr 00:02:A5:8A:13:A6
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2800-0x2807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2808-0x280f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 24X CD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
input: PC Speaker as /class/input/input1
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.1 failed with error -22
piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
piix4_smbus 0000:00:0f.0: SMB base address uninitialized - upgrade BIOS or use
force_addr=0xaddr
Adding 473876k swap on /dev/ida/c0d0p7. Priority:-1 extents:1 across:473876k
EXT3 FS on ida/c0d0p1, internal journal
Probing IDE interface ide0...
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on ida/c0d0p9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on ida/c0d0p8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on ida/c0d0p5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on ida/c0d0p6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
____________________________________
End dmesg
Begin lsmod:
____________________________________
Module Size Used by
ipv6 229184 16
nfs 193108 1
lockd 54952 2 nfs
nfs_acl 3488 1 nfs
sunrpc 136420 4 nfs,lockd,nfs_acl
dm_mod 49204 0
ide_generic 1344 0 [permanent]
ide_disk 14816 0
i2c_piix4 8368 0
i2c_core 19840 1 i2c_piix4
evdev 8992 0
sworks_agp 8832 0
psmouse 34696 0
agpgart 29864 1 sworks_agp
pcspkr 3460 0
serio_raw 6916 0
floppy 57200 0
ext3 118152 5
jbd 51412 1 ext3
mbcache 8292 1 ext3
ide_cd 35936 0
cdrom 32304 1 ide_cd
serverworks 8264 0 [permanent]
generic 4388 0 [permanent]
ide_core 113868 5
ide_generic,ide_disk,ide_cd,serverworks,generic
e100 32356 0
mii 5280 1 e100
thermal 13288 0
processor 25896 1 thermal
fan 4676 0
cpqarray 20868 7
____________________________________
End lsmod
Attachment:
pgpnVk654EoSb.pgp
Description: PGP signature