Since your netcat suggestion was so useful, I here is the complete (broken)
dmesg from the initramfs. This is without the floppy module loaded (which
resulted in a bootable system, see previous email).
dmesg:
[0x03] enabled)
Processor #3 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-34
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: root=/dev/ida/c0d0p1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 797.686 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 511648k/524272k available (1505k kernel code, 11980k reserved, 545k
data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1603.26 BogoMIPS
(lpj=3206528)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 03
Booting processor 1/0 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1595.09 BogoMIPS
(lpj=3190195)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 03
Total of 2 processors activated (3198.36 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=8000
checking if image is initramfs... it is
Freeing initrd memory: 4281k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0094, last bus=3
PCI: Using configuration type 1
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:03.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Root Bridge [PCI1] (0000:03)
PCI: Probing PCI hardware (bus 03)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Interrupt Link [FAKE] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [INA0] (IRQs 5 10 11 15) *3
ACPI: PCI Interrupt Link [INA1] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR1] (IRQs 5 *10 11 15)
ACPI: PCI Interrupt Link [ITR2] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR3] (IRQs 5 10 11 15) *7
ACPI: PCI Interrupt Link [ITR4] (IRQs 5 10 *11 15)
ACPI: PCI Interrupt Link [INB0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB1] (IRQs 5 10 11 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Device 0000:00:00.0 not found by BIOS
PCI: Device 0000:00:00.1 not found by BIOS
PCI: Device 0000:00:0f.0 not found by BIOS
pnp: 00:01: ioport range 0xf50-0xf58 has been reserved
audit: initializing netlink socket (disabled)
audit(1154281037.824:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI wakeup devices:
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 176k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Thermal Zone [THM0] (8 C)
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 177
sym53c8xx 0000:00:01.0: device not supported
ACPI: PCI interrupt for device 0000:00:01.0 disabled
Compaq SMART2 Driver (v 2.6.0)
cpqarray: Device 0x10 has been found at bus 0 dev 1 func 0
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 177
cpqarray: Finding drives on ida0<4>cpqarray ida0: idaSendPciCmd Timeout out,
No command list address returned!
cpqarray: error sending ID controller
cpqarray: Starting firmware's background processing
cpqarray ida0: idaSendPciCmd Timeout out, No command list address returned!
cpqarray: Unable to start background processing
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2800-0x2807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2808-0x280f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
Probing IDE interface ide1...
hdc: Compaq CRN-8241B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 17 (level, low) -> IRQ 185
e100: eth0: e100_probe: addr 0xc6fff000, irq 185, MAC addr 00:50:8B:E1:61:6F
ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 24 (level, low) -> IRQ 193
e100: eth1: e100_probe: addr 0xc6dff000, irq 193, MAC addr 00:50:8B:E1:61:6E
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
Probing IDE interface ide0...
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Attachment:
pgpR2W5aV0DAx.pgp
Description: PGP signature