Bug#359284: Segmentation fault during boot, after "ide1 at ...", before "kjournald starting."
Package: kernel-image-2.6.8-3-686
Version: 2.6.8-16sarge2
Segmentation fault message during boot. It apperas here
...
hdd: ATAPI 48X CDROM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Segmentation fault
kjournald starting. Commit interval 5 seconds
...
Since I have several other configuration problems, like pciehp, shpchp messages, sendmail config, keyboard config, automatic poweroff without acpi, etc., I cite the first one during boot. Unfortunately, it appears before bootlogd may start.
'uname -a ' says
Linux localhost 2.6.8-3-686 #1 Thu Feb 9 07:39:48 UTC 2006 i686 GNU/Linux
'dpkg -s libc6 | grep ^Version' says
Version: 2.3.2.ds1-22sarge2
'lspci -vv' says
0000:00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
0000:00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: e4000000-e7ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
0000:00:0f.0 Ethernet controller: VIA Technologies, Inc. VT86C100A [Rhine] (rev 06)
Subsystem: D-Link System Inc DFE-530TX rev A
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (29500ns min, 38000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e400 [size=128]
Region 1: Memory at eb000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at ea000000 [disabled] [size=64K]
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RF/SG AGP (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Magnum/Xpert128/X99/Xpert2000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at d000 [size=256]
Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [50] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
'dmesg' says
Linux version 2.6.8-3-686 (root@lart) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Thu Feb 9 07:39:48 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32752
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28656 pages, LIFO batch:6
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: BOOT_IMAGE=linux ro root=301
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 512 (order 9: 4096 bytes)
Detected 434.433 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 122032k/131008k available (1552k kernel code, 8420k reserved, 689k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 858.11 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0183fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Celeron (Mendocino) stepping 05
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 434.0242 MHz.
..... host bus clock speed is 66.0806 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4556k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb170, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbd60
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbd88, dseg 0xf0000
pnp: 00:0b: ioport range 0x208-0x20f has been reserved
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
PCI: IRQ 0 for device 0000:00:07.2 doesn't match PIRQ mask - try pci=usepirqmask
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
pnp: SB audio device quirk - increasing port range
pnp: AWE32 quirk - adding two ports
isapnp: Card 'Creative SB AWE64 PnP'
isapnp: 1 Plug & Play card detected total
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4556 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC26400R, ATA DISK drive
hdb: WDC AC34300L, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 12594960 sectors (6448 MB) w/512KiB Cache, CHS=13328/15/63, UDMA(33)
/dev/ide/host0/bus0/target0/lun0: p1 p2
hdb: max request size: 128KiB
hdb: 8406720 sectors (4304 MB) w/256KiB Cache, CHS=8896/15/63, UDMA(33)
/dev/ide/host0/bus0/target1/lun0: p1 p2
hdc: HL-DT-ST DVDRAM GSA-4120B, ATAPI CD/DVD-ROM drive
hdd: ATAPI 48X CDROM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on hda1, internal journal
Generic RTC Driver v1.07
sb: Init: Starting Probe...
pnp: Device 01:01.00 activated.
sb: PnP: Found Card Named = "Creative SB AWE64 PnP", Card PnP id = CTL00C5, Device PnP id = CTL0045
sb: PnP: Detected at: io=0x220, irq=10, dma=1, dma16=5
SB 4.16 detected OK (220)
sb: Turning on MPU
sb: Init: Done
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 440LX Chipset.
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: AGP aperture is 64M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: IRQ 0 for device 0000:00:07.2 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Assigned IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: Intel Corp. 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: irq 11, io base 0000e000
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
PCI: Found IRQ 11 for device 0000:00:0f.0
via-rhine: probe of 0000:00:0f.0 failed with error -975642080
input: PC Speaker
input: PS/2 Logitech Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
inserting floppy driver for 2.6.8-3-686
Floppy drive(s): fd0 is 1.44M<6>ts: Compaq touchscreen protocol output
, fd1 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x278, irq 5 [PCSPP,TRISTATE]
parport1: PC-style at 0x378 [PCSPP]
pnp: Device 01:01.01 activated.
gameport: NS558 PnP at pnp01:01.01 io 0x200 size 8 speed 677 kHz
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33)
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0300140(lo)
IPv6 over IPv4 tunneling driver
[drm] Initialized r128 2.5.0 20030725 on minor 0: ATI Technologies Inc Rage 128 RF/SG AGP
agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
after turning on bootlogd I got the followin gin /var/log/boot:
Mon Mar 27 19:28:23 2006: bootlogd.
Mon Mar 27 19:28:23 2006: Activating swap.
Mon Mar 27 19:28:23 2006: Checking root file system...
Mon Mar 27 19:28:23 2006: fsck 1.37 (21-Mar-2005)
Mon Mar 27 19:28:23 2006: /dev/hda1: clean, 92250/1048576 files, 1372888/2096451 blocks
Mon Mar 27 19:28:24 2006: Board 1 has Identity 7f 18 bd b0 35 c5 00 8c 0e: CTL00c5 Serial No 415084597 [checksum 7f]
Mon Mar 27 19:28:24 2006: CTL00c5/415084597[0]{Audio }: Ports 0x220 0x300 0x388; IRQ5 DMA0 DMA5 --- Enabled OK
Mon Mar 27 19:28:24 2006: CTL00c5/415084597[1]{Game }: Port 0x200; --- Enabled OK
Mon Mar 27 19:28:24 2006: CTL00c5/415084597[2]{WaveTable }: Port 0x620; --- Enabled OK
Mon Mar 27 17:28:27 2006: System time was Mon Mar 27 15:28:27 UTC 2006.
Mon Mar 27 17:28:27 2006: Setting the System Clock using the Hardware Clock as reference...
Mon Mar 27 17:28:29 2006: System Clock set. System local time is now Mon Mar 27 17:28:29 CEST 2006.
Mon Mar 27 17:28:29 2006: Cleaning up ifupdown...done.
Mon Mar 27 17:28:29 2006: Calculating module dependencies... done.
Mon Mar 27 17:28:31 2006: Loading modules...
Mon Mar 27 17:28:31 2006: sb
Mon Mar 27 17:28:32 2006: All modules loaded.
Mon Mar 27 17:28:32 2006: Creating device-mapper devices...done.
Mon Mar 27 17:28:32 2006: Checking all file systems...
Mon Mar 27 17:28:33 2006: fsck 1.37 (21-Mar-2005)
Mon Mar 27 17:28:33 2006: dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Mon Mar 27 17:28:33 2006: dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Mon Mar 27 17:28:35 2006: /dev/hdb1: 2 files, 3/731523 clusters
Mon Mar 27 17:28:36 2006: /dev/hdb2: clean, 398/634880 files, 119010/1269135 blocks
Mon Mar 27 17:28:47 2006: /dev/hda2: 19122 files, 855480/1048195 clusters
Mon Mar 27 17:28:47 2006: Setting kernel variables ...
Mon Mar 27 17:28:48 2006: ... done.
Mon Mar 27 17:28:48 2006: Mounting local filesystems...
Mon Mar 27 17:28:48 2006: /dev/hdb2 on /home type ext3 (rw)
Mon Mar 27 17:28:48 2006: Cleaning /tmp /var/run /var/lock.
Mon Mar 27 17:28:49 2006: Setting up resolvconf...done.
Mon Mar 27 17:28:49 2006: Running 0dns-down to make sure resolv.conf is ok...done.
Mon Mar 27 17:28:49 2006: Setting up networking...done.
Mon Mar 27 17:28:49 2006: Starting hotplug subsystem:
Mon Mar 27 17:28:49 2006: pci
Mon Mar 27 17:28:52 2006: intel-agp: loaded successfully
Mon Mar 27 17:28:54 2006: modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-3-686/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted
Mon Mar 27 17:28:54 2006:
Mon Mar 27 17:28:54 2006: pciehp: can't be loaded
Mon Mar 27 17:28:54 2006: missing kernel or user mode driver pciehp
Mon Mar 27 17:28:54 2006: modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-3-686/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted
Mon Mar 27 17:28:54 2006:
Mon Mar 27 17:28:54 2006: shpchp: can't be loaded
Mon Mar 27 17:28:54 2006: missing kernel or user mode driver shpchp
Mon Mar 27 17:28:58 2006: piix: already loaded
Mon Mar 27 17:29:01 2006: uhci-hcd: loaded successfully
Mon Mar 27 17:29:06 2006: via-rhine: loaded successfully
Mon Mar 27 17:29:06 2006: ignoring pci display device 01:00.0
Mon Mar 27 17:29:06 2006: pci [success]
Mon Mar 27 17:29:06 2006: usb
Mon Mar 27 17:29:08 2006: usb [success]
Mon Mar 27 17:29:08 2006: isapnp
Mon Mar 27 17:29:08 2006: modprobe: FATAL: Error inserting rtc (/lib/modules/2.6.8-3-686/kernel/drivers/char/rtc.ko): No such device
Mon Mar 27 17:29:08 2006:
Mon Mar 27 17:29:08 2006: rtc: can't be loaded
Mon Mar 27 17:29:08 2006: pcspkr: loaded sucessfully
Mon Mar 27 17:29:10 2006: psmouse: loaded sucessfully
Mon Mar 27 17:29:13 2006: floppy: loaded sucessfully
Mon Mar 27 17:29:13 2006: parport_pc: loaded sucessfully
Mon Mar 27 17:29:14 2006: ns558: loaded sucessfully
Mon Mar 27 17:29:14 2006: analog: loaded sucessfully
Mon Mar 27 17:29:14 2006: isapnp [success]
Mon Mar 27 17:29:14 2006: ide
Mon Mar 27 17:29:15 2006: ide-cd: loaded sucessfully
Mon Mar 27 17:29:15 2006: ide [success]
Mon Mar 27 17:29:15 2006: input
Mon Mar 27 17:29:15 2006: evdev: already loaded
Mon Mar 27 17:29:15 2006: evdev: already loaded
Mon Mar 27 17:29:16 2006: evdev: already loaded
Mon Mar 27 17:29:16 2006: mousedev: already loaded
Mon Mar 27 17:29:16 2006: tsdev: already loaded
Mon Mar 27 17:29:16 2006: input [success]
Mon Mar 27 17:29:16 2006: scsi
Mon Mar 27 17:29:16 2006: scsi [success]
Mon Mar 27 17:29:16 2006: done.
Mon Mar 27 17:29:16 2006: Setting up IP spoofing protection: rp_filter.
Mon Mar 27 17:29:16 2006: Configuring network interfaces...Updating sendmail.cf ...
Mon Mar 27 17:29:17 2006: Creating /etc/mail/relay-domains
Mon Mar 27 17:29:18 2006: # Optional file...
Mon Mar 27 17:29:18 2006: A forced reload...
Mon Mar 27 17:29:18 2006: ** ** You should issue `/etc/init.d/sendmail reload` ** **
Mon Mar 27 17:30:20 2006: Mail Transport Agent: sendmail is not running
Mon Mar 27 17:30:20 2006: done.
Mon Mar 27 17:30:20 2006: Starting portmap daemon: portmap.
Mon Mar 27 17:30:21 2006: Loading the saved-state of the serial devices...
Mon Mar 27 17:30:21 2006: /dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
Mon Mar 27 17:30:21 2006: /dev/ttyS1 at 0x02f8 (irq = 3) is a 16550A
Mon Mar 27 17:30:21 2006: ^[]R^[[9;30]^[[14;30]
Mon Mar 27 17:30:22 2006: Setting the System Clock using the Hardware Clock as reference...
Mon Mar 27 17:30:23 2006: System Clock set. Local time: Mon Mar 27 17:30:23 CEST 2006
Mon Mar 27 17:30:23 2006:
Mon Mar 27 17:30:23 2006: Initializing random number generator...done.
Mon Mar 27 17:30:23 2006: Setting up X server socket directory /tmp/.X11-unix...done.
Mon Mar 27 17:30:23 2006: Setting up ICE socket directory /tmp/.ICE-unix...done.
Mon Mar 27 17:30:23 2006: INIT: Entering runlevel: 2
Mon Mar 27 17:30:24 2006: Starting system log daemon: syslogd.
Mon Mar 27 17:30:24 2006: Starting kernel log daemon: klogd.
Mon Mar 27 17:30:24 2006: Starting portmap daemon: portmap.
Mon Mar 27 17:30:25 2006: Starting dictionary server: dictd.
Mon Mar 27 17:30:27 2006: Starting file alteration monitor: FAM.
Mon Mar 27 17:30:27 2006: Starting mouse interface server: gpm.
Mon Mar 27 17:30:28 2006: Starting internet superserver: inetd.
Mon Mar 27 17:30:30 2006: Starting OpenBSD Secure Shell server: sshd.
Mon Mar 27 17:30:30 2006: Setting up X font server socket directory /tmp/.font-unix...done.
Mon Mar 27 17:30:31 2006: Starting X font server: xfs.
Mon Mar 27 17:30:31 2006: Starting Mail Transport Agent: sendmail.
Mon Mar 27 17:31:34 2006: Starting deferred execution scheduler: atd.
Mon Mar 27 17:31:34 2006: Starting periodic command scheduler: cron.
_______________________________________________
Join Excite! - http://www.excite.com
The most personalized portal on the Web!
Reply to: