2006-01-03, k keltezéssel 20.53-kor David Schmitt ezt írta: > Tomorrow, 2.6.15 will be released to unstable, since 2.6.13 should have > received ACPI updates it might be interesting to test this again. I have just tested it with 2.6.15-2. It still does not work. I have attached the dmesg outputs for normal kernel booting, for pci=routeirq and for acpi=off. * * * On Tue, 3 Jan 2006, Christian Aichinger <Greek0@gmx.net> wrote: -------------------------------------------------------------- According to the kernel.org bugtracker this problem seems to be related to a broken DSDT table supplied by the BIOS, and there doesn't seem to be a simple generic way to work around this in the Linux kernel. -------------------------------------------------------------- Well, kernels up to 2.6.8 managed to parse it somehow. Would it be impossible to brink back the old behavior somehow? (Maybe enabled with a kernel param.) Kristof Csillag
Linux version 2.6.15 (2.6.15-10.00.Custom) (root@csillag) (gcc version 4.0.3 20060104 (prerelease) (Debian 4.0.2-6)) #1 SMP PREEMPT Thu Jan 12 08:54:27 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. found SMP MP-table at 000f5f20 On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 126960 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:0 DMI 2.2 present. ACPI: RSDP (v000 VIA694 ) @ 0x000f7850 ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 VIA694 0x00000000 0x00000000) @ 0x1fff5880 ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 17 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:8 APIC version 17 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Built 1 zonelists Kernel command line: root=/dev/hda5 ro video=matroxfb:vesa:0x1B8 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 801.951 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 513828k/524224k available (2879k kernel code, 9868k reserved, 795k data, 244k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1607.59 BogoMIPS (lpj=3215183) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: Intel Pentium III (Coppermine) stepping 06 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1603.77 BogoMIPS (lpj=3207556) CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium III (Coppermine) stepping 06 Total of 2 processors activated (3211.36 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=1 PCI: Using configuration type 1 mtrr: your CPUs had inconsistent variable MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 4000-40ff claimed by vt82c586 ACPI PCI quirk: region 6000-607f claimed by vt82c686 HW-mon PCI quirk: region 5000-500f claimed by vt82c686 SMB Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: d6000000-d8ffffff PREFETCH window: d4000000-d5ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 audit: initializing netlink socket (disabled) audit(1137055588.604:1): initialized Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.0 20040925 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hda: QUANTUM FIREBALLP LM30, ATA DISK drive Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-M1402, ATAPI CD/DVD-ROM drive Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63 hda: cache flushes not supported hda: hda1 hda2 hda3 < hda5 hda6 > hda4 hdc: ATAPI 40X DVD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available USB Universal Host Controller Interface driver v2.3 mice: PS/2 mouse device common for all mice i2c /dev entries driver device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com padlock: VIA PadLock not detected. Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC). ALSA device list: No soundcards found. oprofile: using NMI interrupt. NET: Registered protocol family 2 input: AT Translated Set 2 keyboard as /class/input/input0 IP route cache hash table entries: 8192 (order: 3, 32768 bytes) TCP established hash table entries: 32768 (order: 6, 393216 bytes) TCP bind hash table entries: 32768 (order: 6, 393216 bytes) TCP: Hash tables configured (established 32768 bind 32768) TCP reno registered ip_conntrack version 2.4 (4095 buckets, 32760 max) - 216 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode ReiserFS: hda5: found reiserfs format "3.6" with standard journal ReiserFS: hda5: using ordered data mode ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda5: checking transaction log (hda5) ReiserFS: hda5: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 244k freed parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,EPP] input: PC Speaker as /class/input/input1 input: ImPS/2 Logitech Wheel Mouse as /class/input/input2 Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k fuse init (API version 7.3) libata version 1.20 loaded. ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names lp0: using parport0 (interrupt-driven).
Linux version 2.6.15 (2.6.15-10.00.Custom) (root@csillag) (gcc version 4.0.3 20060104 (prerelease) (Debian 4.0.2-6)) #1 SMP PREEMPT Thu Jan 12 08:54:27 CET 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f5f20
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 126960 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI 2.2 present.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 6:8 APIC version 17
Processor #1 6:8 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 ro acpi=off video=matroxfb:vesa:0x1B8
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 801.966 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 513828k/524224k available (2879k kernel code, 9868k reserved, 795k data, 244k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1607.55 BogoMIPS (lpj=3215115)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 06
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1603.78 BogoMIPS (lpj=3207566)
CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 06
Total of 2 processors activated (3211.34 BogoMIPS).
ExtINT not setup in hardware but reported by MP table
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=1
PCI: Using configuration type 1
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20050902
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-40ff claimed by vt82c586 ACPI
PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
PCI quirk: region 5000-500f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: d6000000-d8ffffff
PREFETCH window: d4000000-d5ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
audit: initializing netlink socket (disabled)
audit(1137055343.612:1): initialized
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
PCI: Enabling Via external APIC routing
matroxfb: Matrox G450 detected
PInS memtype = 4
matroxfb: MTRR's turned on
matroxfb: 1024x768x24bpp (virtual: 1024x5461)
matroxfb: framebuffer at 0xD4000000, mapped to 0xe0880000, size 16777216
Console: switching to colour frame buffer device 128x48
fb0: MATROX frame buffer device
matroxfb_crtc2: secondary head of fb0 was registered as fb1
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
[drm] Initialized drm 1.0.0 20040925
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xe080a000, 00:20:18:8d:3d:40, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139B'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM FIREBALLP LM30, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-M1402, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20265: IDE controller at PCI slot 0000:00:0c.0
PDC20265: chipset revision 2
PDC20265: ROM enabled at 0x30000000
PDC20265: 100% native mode on irq 11
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:pio, hdf:DMA
ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:DMA, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 128KiB
hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63, UDMA(66)
hda: cache flushes not supported
hda: hda1 hda2 hda3 < hda5 hda6 > hda4
hdc: ATAPI 40X DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbmon: debugfs is not available
USB Universal Host Controller Interface driver v2.3
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 5, io base 0x00009400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 5, io base 0x00009800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
input: AT Translated Set 2 keyboard as /class/input/input0
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
padlock: VIA PadLock not detected.
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC).
PCI: Setting latency timer of device 0000:00:07.5 to 64
usb 1-1: new full speed USB device using uhci_hcd and address 2
ALSA device list:
#0: VIA 82C686A/B rev20 with W83971D at 0x9c00, irq 11
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 393216 bytes)
TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 216 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 244k freed
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
Linux video capture interface: v1.00
pwc Philips webcam module version 9.0.2-unofficial loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
pwc Logitech QuickCam 4000 Pro USB webcam detected.
pwc Registered as /dev/video0.
usbcore: registered new driver Philips webcam
usbcore: registered new driver snd-usb-audio
Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k
fuse init (API version 7.3)
libata version 1.20 loaded.
ReiserFS: hda6: found reiserfs format "3.6" with standard journal
ReiserFS: hda6: using ordered data mode
ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda6: checking transaction log (hda6)
ReiserFS: hda6: Using r5 hash to sort names
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
lp0: using parport0 (interrupt-driven).
[drm] Initialized mga 3.2.0 20050607 on minor 0:
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Initialized card for AGP DMA.
pwc Failed to set LED on/off time.
pwc type = 740
pwc type = 740
pwc set_video_mode(176x144 @ 10, palette 15).
pwc decode_size = 1.
pwc Using alternate setting 1.
Linux version 2.6.15 (2.6.15-10.00.Custom) (root@csillag) (gcc version 4.0.3 20060104 (prerelease) (Debian 4.0.2-6)) #1 SMP PREEMPT Thu Jan 12 08:54:27 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. found SMP MP-table at 000f5f20 On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 126960 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:0 DMI 2.2 present. ACPI: RSDP (v000 VIA694 ) @ 0x000f7850 ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 VIA694 0x00000000 0x00000000) @ 0x1fff5880 ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 17 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:8 APIC version 17 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Built 1 zonelists Kernel command line: root=/dev/hda5 ro pci=routerirq video=matroxfb:vesa:0x1B8 PCI: Unknown option `routerirq' mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 801.966 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 513828k/524224k available (2879k kernel code, 9868k reserved, 795k data, 244k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1607.50 BogoMIPS (lpj=3215009) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: Intel Pentium III (Coppermine) stepping 06 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1603.78 BogoMIPS (lpj=3207566) CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium III (Coppermine) stepping 06 Total of 2 processors activated (3211.28 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=1 PCI: Using configuration type 1 mtrr: your CPUs had inconsistent variable MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 4000-40ff claimed by vt82c586 ACPI PCI quirk: region 6000-607f claimed by vt82c686 HW-mon PCI quirk: region 5000-500f claimed by vt82c686 SMB Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: d6000000-d8ffffff PREFETCH window: d4000000-d5ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 audit: initializing netlink socket (disabled) audit(1137055834.600:1): initialized Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.0 20040925 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hda: QUANTUM FIREBALLP LM30, ATA DISK drive Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-M1402, ATAPI CD/DVD-ROM drive Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63 hda: cache flushes not supported hda: hda1 hda2 hda3 < hda5 hda6 > hda4 hdc: ATAPI 40X DVD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available USB Universal Host Controller Interface driver v2.3 mice: PS/2 mouse device common for all mice i2c /dev entries driver device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com padlock: VIA PadLock not detected. Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC). ALSA device list: No soundcards found. oprofile: using NMI interrupt. NET: Registered protocol family 2 input: AT Translated Set 2 keyboard as /class/input/input0 IP route cache hash table entries: 8192 (order: 3, 32768 bytes) TCP established hash table entries: 32768 (order: 6, 393216 bytes) TCP bind hash table entries: 32768 (order: 6, 393216 bytes) TCP: Hash tables configured (established 32768 bind 32768) TCP reno registered ip_conntrack version 2.4 (4095 buckets, 32760 max) - 216 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode ReiserFS: hda5: found reiserfs format "3.6" with standard journal ReiserFS: hda5: using ordered data mode ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda5: checking transaction log (hda5) ReiserFS: hda5: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 244k freed parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,EPP] input: PC Speaker as /class/input/input1 input: ImPS/2 Logitech Wheel Mouse as /class/input/input2 Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k fuse init (API version 7.3) libata version 1.20 loaded. ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names lp0: using parport0 (interrupt-driven).
Attachment:
signature.asc
Description: This is a digitally signed message part