Bug#307457: kernel-image-2.6.10-1-686-smp: running into oom-killer: gfp_mask=0xd0 often
Hi,
On Tue, 03.05.2005 at 12:16:51 +0200, maximilian attems <debian@sternwelten.at> wrote:
> On Tue, 03 May 2005, Toni Mueller wrote:
> > Package: kernel-image-2.6.10-1-686-smp
> > Severity: important
> >
> > I find error messages like the one above (not sure about the actual
> > value of gfp_mask) on a regular basis in the logs. Sometimes I just find
> > out hard because the machine simply crashes shortly after. This makes
> > the machine in question unreliable, crashing at least every few weeks.
> > Therefore I'm flagging this bug as "important".
> >
> > Hardware is a rather new IBM x205, with ServeRAID4, GigE, and 1GB RAM.
>
> you didn't report the error message?!
> dmesg after boot would also be usefull.
Ok. I thought I was clear enough. The error messages I see are at
least:
oom-killer: gfp_mask=0xd0
oom-killer: gfp_mask=0x1d2
oom-killer: gfp_mask=0x4d0
> anyway please try kernel-image-2.6.11 from unstable!
This is currently impossible, due to #306930. Currently, I try to fix
this (ie, create a local kernel-nonfree-... package).
Dmesg:
Linux version 2.6.10-1-686-smp (dilinger@toaster.hq.voxel.net) (gcc version 3.3.5 (Debian 1:3.3.5-6)) #1 SMP Tue Jan 18 03:03:11 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
BIOS-e820: 000000003ffd0000 - 000000003ffd8000 (ACPI data)
BIOS-e820: 000000003ffd8000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fa460
On node 0 totalpages: 262096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 32720 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 IBM ) @ 0x000fe030
ACPI: RSDT (v001 IBM M51G 0x00000001 IBM 0x00000001) @ 0x3ffd0000
ACPI: FADT (v001 IBM M51G 0x00000001 IBM 0x00000001) @ 0x3ffd0125
ACPI: ASF! (v016 IBM 0x01000000 0x00000000) @ 0x3ffd0030
ACPI: MADT (v001 IBM M51G 0x00000001 IBM 0x00000001) @ 0x3ffd00cb
ACPI: DSDT (v001 IBM M51G 0x00001000 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=2610 ro root=801
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2666.565 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030856k/1048384k available (1700k kernel code, 16960k reserved, 711k data, 200k init, 130880k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5275.64 BogoMIPS (lpj=2637824)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09
per-CPU timeslice cutoff: 1463.12 usecs.
task migration cache decay timeout: 2 msecs.
Total of 1 processors activated (5275.64 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
CPU0:
domain 0: span 01
groups: 01
domain 1: span 01
groups: 01
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4764k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0220, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [PILA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [PILC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PILF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PILG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled by ACPI
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:0d: ioport range 0x400-0x47f could not be reserved
pnp: 00:0d: ioport range 0x480-0x4b7 has been reserved
pnp: 00:0d: ioport range 0x4b9-0x4c0 could not be reserved
pnp: 00:0d: ioport range 0xe00-0xe7f has been reserved
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
PCI2 PS2M KBC0 COM1 COM2 USB0 USB1
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4764KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 200k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 169
ips 0000:02:01.0: Warning ! ! ! ServeRAID Version Mismatch
ips 0000:02:01.0: Bios = 4.84.01, Firmware = 4.84.01, Device Driver = 7.10.18
ips 0000:02:01.0: These levels should match to avoid possible compatibility problems.
scsi0 : IBM PCI ServeRAID 7.10.18 Build 731 <ServeRAID 4Lx>
elevator: using anticipatory as default io scheduler
Vendor: IBM Model: SERVERAID Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Vendor: IBM Model: SERVERAID Rev: 1.00
Type: Processor ANSI SCSI revision: 02
Vendor: IBM Model: YGLv3 S2 Rev: 0
Type: Processor ANSI SCSI revision: 02
SCSI device sda: 71096320 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 71096320 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 p12 p13 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
EXT3-fs: recovery complete.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2104220k swap on /dev/sda5. Priority:-1 extents:1
EXT3 FS on sda1, internal journal
Generic RTC Driver v1.07
tg3.c:v3.14 (November 15, 2004)
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177
tg3: tg3_request_firmware (eth%d): Couldn't get firmware "tg3/tso-1.4.0".
tg3: eth%d: Firmware "tg3/tso-1.4.0" not loaded; continuing without TSO.
eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:09:6b:37:ff:e4
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0]
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
and so on... it continues to mount file systems until it's ready.
Best,
--Toni++
Reply to: