Bug#270376: PCMCIA Nic stops working after upgrading to 2.6.6/7/8
I'm downloading and testing all 3 now.
The short version is none of the 3 worked (same problem as what I've already
seen on 2.6.6-10. Further details, dmsg, etc. below.
----------------
Thanks
Jefferson Cowart
Jeff@cowart.net
> -----Original Message-----
> From: maximilian attems [mailto:debian@sternwelten.at]
> Sent: Tuesday, March 29, 2005 06:49
> To: Jefferson Cowart; 270376@bugs.debian.org
> Subject: Re: Bug#270376: PCMCIA Nic stops working after
> upgrading to 2.6.6/7/8
>
> [ sorry for late reply, but was quit busy ]
>
> in the meantime there is a kernel-source-2.6.11 in unstable,
> built against it an 386 kernel with debian config to see
> if that helps?
#dmsg
mapped APIC to ffffd000 (010fb000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 267.277 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 119284k/128000k available (1387k kernel code, 8168k reserved, 757k
data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 524.28 BogoMIPS (lpj=262144)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 00808131 01818131 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 00808131 01818131 00000000 00000000
00000000 00000000 00000000
Working around Cyrix MediaGX virtual DMA bugs.
CPU: After all inits, caps: 00808131 00818131 00000000 00000001 00000000
00000000 00000000
CPU: Cyrix MediaGXtm MMXtm Enhanced stepping 02
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (bad gzip magic numbers); looks
like an initrd
Freeing initrd memory: 4352k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9b4, last bus=0
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7920
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xaa24, dseg 0x400
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pnp: 00:00: ioport range 0x398-0x399 has been reserved
pnp: 00:0a: ioport range 0x480-0x48f has been reserved
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x14)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 3
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4352KiB [1 disk] into ram disk...
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Cyrix 5520: IDE controller at PCI slot 0000:00:12.0
ide0: BM-DMA at 0x5000-0x5007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x5008-0x500f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK2105MAV, ATA DISK drive
PIO clocking = 4
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-ROM CDR_U241, ATAPI CD/DVD-ROM drive
PIO clocking = 4
ide1 at 0x170-0x177,0x376 on irq 14
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 4233600 sectors (2167 MB), CHS=4200/16/63
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 249944k swap on /dev/hda1. Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Generic RTC Driver v1.07
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:00:07.0 [0000:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:07.0, mfunc 0x0ba43822, devctl 0x62
Yenta: ISA IRQ mask 0x0010, PCI irq 10
Socket status: 30000010
Yenta: CardBus bridge found at 0000:00:07.1 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:07.1, mfunc 0x0ba43822, devctl 0x62
irq 10: nobody cared!
[<c01297b5>] __report_bad_irq+0x31/0x77
[<c012985f>] note_interrupt+0x4c/0x71
[<c0129476>] __do_IRQ+0x93/0xbd
[<c0104b35>] do_IRQ+0x19/0x24
[<c01038ba>] common_interrupt+0x1a/0x20
[<c01189a4>] __do_softirq+0x2c/0x7d
[<c0118a17>] do_softirq+0x22/0x26
[<c0104b3a>] do_IRQ+0x1e/0x24
[<c01038ba>] common_interrupt+0x1a/0x20
[<c011c05c>] msleep+0x4/0x35
[<c8920060>] yenta_get_status+0x39/0xb8 [yenta_socket]
[<c8921bc2>] yenta_probe_cb_irq+0xa7/0xe3 [yenta_socket]
[<c8921334>] ti12xx_irqroute_func1+0x73/0x1ce [yenta_socket]
[<c89215b2>] ti12xx_override+0x123/0x132 [yenta_socket]
[<c8921e6a>] yenta_probe+0x12f/0x1ef [yenta_socket]
[<c019df59>] pci_device_probe_static+0x2e/0x41
[<c019df8b>] __pci_device_probe+0x1f/0x32
[<c019dfba>] pci_device_probe+0x1c/0x31
[<c01e6c2e>] driver_probe_device+0x36/0x54
[<c01e6d07>] driver_attach+0x39/0x6e
[<c01e7082>] bus_add_driver+0x5e/0x80
[<c01e73ff>] driver_register+0x2d/0x31
[<c019e157>] pci_register_driver+0x57/0x6a
[<c889400a>] yenta_socket_init+0xa/0xc [yenta_socket]
[<c012740c>] sys_init_module+0xbd/0x179
[<c0102ed3>] syscall_call+0x7/0xb
handlers:
[<c89206f7>] (yenta_interrupt+0x0/0x27 [yenta_socket])
Disabling IRQ #10
Yenta TI: socket 0000:00:07.1 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:07.1 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0010, PCI irq 0
Socket status: 30000006
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Guessed IRQ 9 for device 0000:00:13.0
ohci_hcd 0000:00:13.0: Compaq Computer Corporation ZFMicro Chipset USB
ohci_hcd 0000:00:13.0: irq 9, pci mem 0xfedfe000
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using ohci_hcd and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
input: PC Speaker
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
cs: IO port probe 0x100-0x4ff: excluding 0x220-0x22f 0x300-0x307 0x388-0x38f
cs: IO port probe 0x100-0x4ff: excluding 0x220-0x22f 0x300-0x307 0x388-0x38f
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
ASIC rev 10,<6>eth0: Megahertz 574B at io 0x320, irq 10, hw_addr
00:50:DA:E4:D2:CC.
64K FIFO split 1:1 Rx:Tx, autoselect MII interface.
NET: Registered protocol family 17
eth0: interrupt(s) dropped!
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e60a0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
eth0: no IPv6 routers present
> also there is _lots_ of pcmcia dev going on upstream,
> so i also built for you an -mm kernel you could test?
(Out of curiosity what does the -mm mean?)
Appears to have the same problem as 2.6.6-10.
Also maybe of note: Just before I saw the line about init starting I got a
ton of errors about can't remove device: "some_device" device or resource
busy. I didn't see how many as they scrolled off the screen, but there were
a large number.
#dmsg
Linux version 2.6.12-rc1-mm3.050329 (root@aipc54) (gcc version 3.3.5 (Debian
1:3.3.5-8)) #1 Tue Mar 29 12:22:38 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ed800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007d00000 (usable)
BIOS-e820: 00000000fffed800 - 0000000100000000 (reserved)
125MB LOWMEM available.
On node 0 totalpages: 32000
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 27904 pages, LIFO batch:6
HighMem zone: 0 pages, LIFO batch:1
DMI not present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 07d00000 (gap: 07d00000:f82ed800)
Built 1 zonelists
No local APIC present or hardware disabled
mapped APIC to ffffd000 (010fb000)
Initializing CPU#0
Kernel command line: root=/dev/hda2 ro
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 267.264 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 119172k/128000k available (1435k kernel code, 8316k reserved, 796k
data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 326.65 BogoMIPS (lpj=163328)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00808131 01818131 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 00808131 01818131 00000000 00000000
00000000 00000000 00000000
Working around Cyrix MediaGX virtual DMA bugs.
CPU: After all inits, caps: 00808131 00818131 00000000 00000001 00000000
00000000 00000000
CPU: Cyrix MediaGXtm MMXtm Enhanced stepping 02
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (bad gzip magic numbers); looks
like an initrd
softlockup thread 0 started up.
Freeing initrd memory: 4412k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9b4, last bus=0
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7920
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xaa24, dseg 0x400
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pnp: 00:00: ioport range 0x398-0x399 has been reserved
pnp: 00:0a: ioport range 0x480-0x48f has been reserved
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x14)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 3
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4412KiB [1 disk] into ram disk... |/-\|/-\<6>input:
AT Translated Set 2 keyboard on isa0060/serio0
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/
-\done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Cyrix 5520: IDE controller at PCI slot 0000:00:12.0
ide0: BM-DMA at 0x5000-0x5007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x5008-0x500f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK2105MAV, ATA DISK drive
PIO clocking = 4
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-ROM CDR_U241, ATAPI CD/DVD-ROM drive
PIO clocking = 4
ide1 at 0x170-0x177,0x376 on irq 14
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 4233600 sectors (2167 MB), CHS=4200/16/63
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 249944k swap on /dev/hda1. Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Generic RTC Driver v1.07
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Yenta: CardBus bridge found at 0000:00:07.0 [0000:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:07.0, mfunc 0x0ba43822, devctl 0x62
Yenta: ISA IRQ mask 0x0010, PCI irq 10
Socket status: 30000010
Yenta: CardBus bridge found at 0000:00:07.1 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:07.1, mfunc 0x0ba43822, devctl 0x62
irq 10: nobody cared (try booting with the "irqpoll" option.
[<c012be09>] __report_bad_irq+0x31/0x77
[<c012bedc>] note_interrupt+0x75/0x99
[<c012ba00>] __do_IRQ+0x95/0xc1
[<c0104cc1>] do_IRQ+0x19/0x24
[<c010395e>] common_interrupt+0x1a/0x20
[<c01184c8>] __do_softirq+0x2c/0x7d
[<c011853b>] do_softirq+0x22/0x26
[<c0104cc6>] do_IRQ+0x1e/0x24
[<c010395e>] common_interrupt+0x1a/0x20
[<c011bf0e>] msleep+0x4/0x35
[<c8923c01>] yenta_probe_cb_irq+0xa7/0xe3 [yenta_socket]
[<c8923373>] ti12xx_irqroute_func1+0x73/0x1ce [yenta_socket]
[<c89235f1>] ti12xx_override+0x123/0x132 [yenta_socket]
[<c8923ead>] yenta_probe+0x133/0x1f3 [yenta_socket]
[<c01a5586>] pci_device_probe_static+0x2e/0x41
[<c01a55b8>] __pci_device_probe+0x1f/0x32
[<c01a55ea>] pci_device_probe+0x1f/0x34
[<c01eef1d>] driver_probe_device+0x45/0x7e
[<c01ef01d>] driver_attach+0x3c/0x74
[<c01eebab>] bus_add_driver+0x5e/0x90
[<c01ef257>] driver_register+0x26/0x29
[<c01a577f>] pci_register_driver+0x4f/0x62
[<c888d00a>] yenta_socket_init+0xa/0xc [yenta_socket]
[<c012980c>] sys_init_module+0xaa/0x166
[<c0102f31>] syscall_call+0x7/0xb
handlers:
[<c89226f7>] (yenta_interrupt+0x0/0x27 [yenta_socket])
Disabling IRQ #10
Yenta TI: socket 0000:00:07.1 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:07.1 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0010, PCI irq 0
Socket status: 30000006
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Guessed IRQ 9 for device 0000:00:13.0
ohci_hcd 0000:00:13.0: Compaq Computer Corporation ZFMicro Chipset USB
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 9, io mem 0xfedfe000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using ohci_hcd and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
input: PC Speaker
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
cs: IO port probe 0x100-0x4ff: excluding 0x220-0x22f 0x300-0x307 0x388-0x38f
cs: IO port probe 0x100-0x4ff: excluding 0x220-0x22f 0x300-0x307 0x388-0x38f
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
ASIC rev 10,<6>eth0: Megahertz 574B at io 0x320, irq 10, hw_addr
00:50:DA:E4:D2:CC.
64K FIFO split 1:1 Rx:Tx, autoselect MII interface.
NET: Registered protocol family 17
eth0: interrupt(s) dropped!
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02fa9c0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
eth0: no IPv6 routers present
> in order to further pin down the change between 2.6.5 and 2.6.6,
> that broke your pcmcia card. i built also an kernel-image-2.6.6-rc1
> for testing, but if 2.6.11 works that may not be needed?
(I forgot to run dmsg but here is the relevant output from syslog)
1 jcc02003-hawk kernel: klogd 1.4.1#16, log source = /proc/kmsg
started.
1 jcc02003-hawk kernel: Inspecting /boot/System.map-2.6.6-rc1.050329
1 jcc02003-hawk cardmgr: watching 2 sockets
1 jcc02003-hawk cardmgr: starting, version is 3.2.5
1 jcc02003-hawk cardmgr: socket 0: 3Com 572/574 Fast Ethernet
1 jcc02003-hawk cardmgr: executing: 'modprobe 3c574_cs'
1 jcc02003-hawk kernel: Loaded 26534 symbols from
/boot/System.map-2.6.6-rc1.050329.
1 jcc02003-hawk kernel: Symbols match kernel version 2.6.6.
1 jcc02003-hawk kernel: No module symbols loaded - kernel modules not
enabled.
1 jcc02003-hawk kernel: Linux version 2.6.6-rc1.050329 (root@aipc54)
(gcc version 3.3.5 (Debian 1:3.3.5-8)) #1 Tue Mar 29 15:37:49 CEST 2005
1 jcc02003-hawk kernel: BIOS-provided physical RAM map:
1 jcc02003-hawk kernel: BIOS-e820: 0000000000000000 -
000000000009fc00 (usable)
1 jcc02003-hawk kernel: BIOS-e820: 000000000009fc00 -
00000000000a0000 (reserved)
1 jcc02003-hawk kernel: BIOS-e820: 00000000000ed800 -
0000000000100000 (reserved)
1 jcc02003-hawk kernel: BIOS-e820: 0000000000100000 -
0000000007d00000 (usable)
1 jcc02003-hawk kernel: BIOS-e820: 00000000fffed800 -
0000000100000000 (reserved)
1 jcc02003-hawk kernel: 125MB LOWMEM available.
1 jcc02003-hawk kernel: On node 0 totalpages: 32000
1 jcc02003-hawk kernel: DMA zone: 4096 pages, LIFO batch:1
1 jcc02003-hawk kernel: Normal zone: 27904 pages, LIFO batch:6
1 jcc02003-hawk kernel: HighMem zone: 0 pages, LIFO batch:1
1 jcc02003-hawk kernel: DMI not present.
1 jcc02003-hawk kernel: ACPI: Unable to locate RSDP
1 jcc02003-hawk kernel: Built 1 zonelists
1 jcc02003-hawk kernel: Kernel command line: root=/dev/hda2 ro
1 jcc02003-hawk kernel: Initializing CPU#0
1 jcc02003-hawk kernel: PID hash table entries: 512 (order 9: 4096
bytes)
1 jcc02003-hawk kernel: Detected 267.277 MHz processor.
1 jcc02003-hawk kernel: Using tsc for high-res timesource
1 jcc02003-hawk kernel: Console: colour VGA+ 80x25
1 jcc02003-hawk kernel: Memory: 119780k/128000k available (1292k
kernel code, 7676k reserved, 670k data, 200k init, 0k highmem)
1 jcc02003-hawk kernel: Checking if this processor honours the WP bit
even in supervisor mode... Ok.
1 jcc02003-hawk kernel: Calibrating delay loop... 524.28 BogoMIPS
1 jcc02003-hawk kernel: Dentry cache hash table entries: 16384
(order: 4, 65536 bytes)
1 jcc02003-hawk kernel: Inode-cache hash table entries: 8192 (order:
3, 32768 bytes)
1 jcc02003-hawk kernel: Mount-cache hash table entries: 512 (order:
0, 4096 bytes)
1 jcc02003-hawk kernel: CPU: After generic identify, caps:
00808131 01818131 00000000 00000000
1 jcc02003-hawk kernel: CPU: After vendor identify, caps:
00808131 01818131 00000000 00000000
1 jcc02003-hawk kernel: Working around Cyrix MediaGX virtual DMA
bugs.
1 jcc02003-hawk kernel: CPU: After all inits, caps: 00808131
00818131 00000000 00000001
1 jcc02003-hawk kernel: CPU: Cyrix MediaGXtm MMXtm Enhanced stepping
02
1 jcc02003-hawk kernel: Checking 'hlt' instruction... OK.
1 jcc02003-hawk kernel: Checking for popad bug... OK.
1 jcc02003-hawk kernel: POSIX conformance testing by UNIFIX
1 jcc02003-hawk kernel: NET: Registered protocol family 16
1 jcc02003-hawk kernel: PCI: PCI BIOS revision 2.10 entry at 0xfd9b4,
last bus=0
1 jcc02003-hawk kernel: PCI: Using configuration type 1
1 jcc02003-hawk kernel: mtrr: v2.0 (20020519)
1 jcc02003-hawk kernel: ACPI: Subsystem revision 20040326
1 jcc02003-hawk kernel: ACPI: Interpreter disabled.
1 jcc02003-hawk kernel: Linux Plug and Play Support v0.97 (c) Adam
Belay
1 jcc02003-hawk kernel: PnPBIOS: Scanning system for PnP BIOS
support...
1 jcc02003-hawk kernel: PnPBIOS: Found PnP BIOS installation
structure at 0xc00f7920
1 jcc02003-hawk kernel: PnPBIOS: PnP BIOS version 1.0, entry
0xf0000:0xaa24, dseg 0x400
1 jcc02003-hawk kernel: PnPBIOS: 17 nodes reported by PnP BIOS; 17
recorded by driver
1 jcc02003-hawk kernel: ACPI: ACPI tables contain no PCI IRQ routing
entries
1 jcc02003-hawk kernel: PCI: Invalid ACPI-PCI IRQ routing table
1 jcc02003-hawk kernel: PCI: Probing PCI hardware
1 jcc02003-hawk kernel: PCI: Probing PCI hardware (bus 00)
1 jcc02003-hawk kernel: VFS: Disk quotas dquot_6.5.1
1 jcc02003-hawk kernel: devfs: 2004-01-31 Richard Gooch
(rgooch@atnf.csiro.au)
1 jcc02003-hawk kernel: devfs: boot_options: 0x0
1 jcc02003-hawk kernel: Initializing Cryptographic API
1 jcc02003-hawk kernel: PCI: Fixup for MediaGX/Geode Slave Disconnect
Boundary (0x41=0x14)
1 jcc02003-hawk kernel: isapnp: Scanning for PnP cards...
1 jcc02003-hawk kernel: isapnp: No Plug & Play device found
1 jcc02003-hawk kernel: RAMDISK driver initialized: 16 RAM disks of
8192K size 1024 blocksize
1 jcc02003-hawk kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
1 jcc02003-hawk kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
1 jcc02003-hawk kernel: input: AT Translated Set 2 keyboard on
isa0060/serio0
1 jcc02003-hawk kernel: EISA: Probing bus 0 at eisa0
1 jcc02003-hawk kernel: NET: Registered protocol family 2
1 jcc02003-hawk kernel: IP: routing cache hash table of 512 buckets,
4Kbytes
1 jcc02003-hawk kernel: TCP: Hash tables configured (established 8192
bind 16384)
1 jcc02003-hawk kernel: NET: Registered protocol family 8
1 jcc02003-hawk kernel: NET: Registered protocol family 20
1 jcc02003-hawk kernel: RAMDISK: cramfs filesystem found at block 0
1 jcc02003-hawk kernel: RAMDISK: Loading 4152 blocks [1 disk] into
ram disk...
|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/
^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^
H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H
|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/
^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^
H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H
|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/
^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^
H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H
|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/
^H-^H\^H|^H/^H-^H\^Hdone.
1 jcc02003-hawk kernel: VFS: Mounted root (cramfs filesystem)
readonly.
1 jcc02003-hawk kernel: NET: Registered protocol family 1
1 jcc02003-hawk kernel: Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
1 jcc02003-hawk kernel: ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
1 jcc02003-hawk kernel: Cyrix 5520: IDE controller at PCI slot
0000:00:12.0
1 jcc02003-hawk kernel: ide0: BM-DMA at 0x5000-0x5007, BIOS
settings: hda:pio, hdb:pio
1 jcc02003-hawk kernel: ide1: BM-DMA at 0x5008-0x500f, BIOS
settings: hdc:pio, hdd:pio
1 jcc02003-hawk kernel: Index.b 0 1
1 jcc02003-hawk kernel: hda: TOSHIBA MK2105MAV, ATA DISK drive
2 jcc02003-hawk kernel: PIO clocking = 4
1 jcc02003-hawk kernel: Using anticipatory io scheduler
1 jcc02003-hawk kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
1 jcc02003-hawk kernel: hdc: CD-ROM CDR_U241, ATAPI CD/DVD-ROM drive
1 jcc02003-hawk kernel: ide1 at 0x170-0x177,0x376 on irq 14
1 jcc02003-hawk kernel: hda: max request size: 128KiB
1 jcc02003-hawk kernel: hda: 4233600 sectors (2167 MB),
CHS=4200/16/63
1 jcc02003-hawk kernel: /dev/ide/host0/bus0/target0/lun0: p1 p2 p3
2 jcc02003-hawk kernel: kjournald starting. Commit interval 5
seconds
2 jcc02003-hawk kernel: EXT3-fs: mounted filesystem with ordered data
mode.
1 jcc02003-hawk kernel: Adding 249944k swap on /dev/hda1.
Priority:-1 extents:1
1 jcc02003-hawk kernel: EXT3 FS on hda2, internal journal
1 jcc02003-hawk kernel: Generic RTC Driver v1.07
1 jcc02003-hawk kernel: hdc: ATAPI 24X CD-ROM drive, 128kB Cache
1 jcc02003-hawk kernel: Uniform CD-ROM driver Revision: 3.20
1 jcc02003-hawk kernel: EXT3 FS on hda3, internal journal
1 jcc02003-hawk kernel: Linux Kernel Card Services
1 jcc02003-hawk kernel: options: [pci] [cardbus] [pm]
1 jcc02003-hawk kernel: Yenta: CardBus bridge found at 0000:00:07.0
[0000:0000]
1 jcc02003-hawk kernel: Yenta: Enabling burst memory read
transactions
2 jcc02003-hawk kernel: Yenta: Using CSCINT to route CSC interrupts
to PCI
2 jcc02003-hawk kernel: Yenta: Routing CardBus interrupts to PCI
1 jcc02003-hawk kernel: Yenta TI: socket 0000:00:07.0, mfunc
0x0ba43822, devctl 0x62
1 jcc02003-hawk kernel: Yenta: ISA IRQ mask 0x0010, PCI irq 10
1 jcc02003-hawk kernel: Socket status: 30000010
1 jcc02003-hawk kernel: Yenta: CardBus bridge found at 0000:00:07.1
[0000:0000]
1 jcc02003-hawk kernel: Yenta TI: socket 0000:00:07.1, mfunc
0x0ba43822, devctl 0x62
1 jcc02003-hawk kernel: irq 10: nobody cared!
1 jcc02003-hawk kernel: Call Trace:
1 jcc02003-hawk kernel: [__report_bad_irq+49/115]
__report_bad_irq+0x31/0x73
1 jcc02003-hawk kernel: [note_interrupt+76/111]
note_interrupt+0x4c/0x6f
1 jcc02003-hawk kernel: [do_IRQ+146/249] do_IRQ+0x92/0xf9
2 jcc02003-hawk kernel: [common_interrupt+24/32]
common_interrupt+0x18/0x20
1 jcc02003-hawk kernel: [__do_softirq+44/115] __do_softirq+0x2c/0x73
1 jcc02003-hawk kernel: [do_softirq+34/38] do_softirq+0x22/0x26
1 jcc02003-hawk kernel: [do_IRQ+229/249] do_IRQ+0xe5/0xf9
1 jcc02003-hawk kernel: [__crc_give_up_console+4011128/4336289]
gen_rtc_read_proc+0x27/0x48 [genrtc]
1 jcc02003-hawk kernel: [schedule_timeout+0/156]
schedule_timeout+0x0/0x9c
1 jcc02003-hawk kernel: [__crc_give_up_console+4058659/4336289]
yenta_probe_cb_irq+0xc1/0xfb [yenta_socket]
1 jcc02003-hawk kernel: [__crc_give_up_console+4056754/4336289]
ti12xx_irqroute_func1+0x73/0x1ce [yenta_socket]
1 jcc02003-hawk kernel: [__crc_give_up_console+4057289/4336289]
ti12xx_override+0xbc/0xca [yenta_socket]
1 jcc02003-hawk kernel: [__crc_give_up_console+4059327/4336289]
yenta_probe+0x125/0x1e5 [yenta_socket]
1 jcc02003-hawk kernel: [pci_device_probe_static+46/65]
pci_device_probe_static+0x2e/0x41
1 jcc02003-hawk kernel: [__pci_device_probe+31/50]
__pci_device_probe+0x1f/0x32
1 jcc02003-hawk kernel: [pci_device_probe+28/49]
pci_device_probe+0x1c/0x31
1 jcc02003-hawk kernel: [bus_match+46/77] bus_match+0x2e/0x4d
1 jcc02003-hawk kernel: [driver_attach+57/110]
driver_attach+0x39/0x6e
1 jcc02003-hawk kernel: [bus_add_driver+82/97]
bus_add_driver+0x52/0x61
1 jcc02003-hawk kernel: [driver_register+45/49]
driver_register+0x2d/0x31
1 jcc02003-hawk kernel: [pci_register_driver+78/107]
pci_register_driver+0x4e/0x6b
1 jcc02003-hawk kernel: [__crc_give_up_console+3970055/4336289]
yenta_socket_init+0xa/0xc [yenta_socket]
1 jcc02003-hawk kernel: [sys_init_module+227/465]
sys_init_module+0xe3/0x1d1
1 jcc02003-hawk kernel: [syscall_call+7/11] syscall_call+0x7/0xb
1 jcc02003-hawk kernel:
1 jcc02003-hawk kernel: handlers:
1 jcc02003-hawk kernel: [__crc_give_up_console+4053730/4336289]
(yenta_interrupt+0x0/0x27 [yenta_socket])
1 jcc02003-hawk kernel: Disabling IRQ #10
1 jcc02003-hawk kernel: Yenta TI: socket 0000:00:07.1 no PCI
interrupts. Fish. Please report.
1 jcc02003-hawk kernel: Yenta: ISA IRQ mask 0x0010, PCI irq 0
1 jcc02003-hawk kernel: Socket status: 30000006
1 jcc02003-hawk kernel: usbcore: registered new driver usbfs
1 jcc02003-hawk kernel: usbcore: registered new driver hub
1 jcc02003-hawk kernel: ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host
Controller (OHCI) Driver (PCI)
1 jcc02003-hawk kernel: ohci_hcd: block sizes: ed 64 td 64
1 jcc02003-hawk kernel: PCI: Guessed IRQ 9 for device 0000:00:13.0
1 jcc02003-hawk kernel: ohci_hcd 0000:00:13.0: Compaq Computer
Corporation ZFMicro Chipset USB
1 jcc02003-hawk kernel: ohci_hcd 0000:00:13.0: irq 9, pci mem
c8898000
1 jcc02003-hawk kernel: ohci_hcd 0000:00:13.0: new USB bus
registered, assigned bus number 1
1 jcc02003-hawk kernel: hub 1-0:1.0: USB hub found
1 jcc02003-hawk kernel: usb 1-1: new full speed USB device using
address 2
1 jcc02003-hawk kernel: hub 1-1:1.0: USB hub found
1 jcc02003-hawk kernel: input: PC Speaker
1 jcc02003-hawk kernel: inserting floppy driver for 2.6.6-rc1.050329
1 jcc02003-hawk kernel: Floppy drive(s): fd0 is 1.44M
1 jcc02003-hawk kernel: FDC 0 is a National Semiconductor PC87306
1 jcc02003-hawk kernel: cs: IO port probe 0x0100-0x04ff: excluding
0x220-0x22f 0x300-0x307 0x388-0x38f
1 jcc02003-hawk kernel: cs: IO port probe 0x0800-0x08ff: clean.
1 jcc02003-hawk kernel: cs: IO port probe 0x0c00-0x0cff: clean.
1 jcc02003-hawk kernel: cs: IO port probe 0x0a00-0x0aff: clean.
1 jcc02003-hawk kernel: cs: memory probe 0xa0000000-0xa0ffffff:
clean.
1 jcc02003-hawk kernel: eth0: Megahertz 574B at io 0x320, irq 10,
hw_addr 00:50:DA:E4:D2:CC.
1 jcc02003-hawk kernel: ASIC rev 10, 64K FIFO split 1:1 Rx:Tx,
autoselect MII interface.
1 jcc02003-hawk kernel: NET: Registered protocol family 17
1 jcc02003-hawk kernel: eth0: interrupt(s) dropped!
1 jcc02003-hawk kernel: NET: Registered protocol family 10
1 jcc02003-hawk kernel: Disabled Privacy Extensions on device
c02b88e0(lo)
1 jcc02003-hawk kernel: IPv6 over IPv4 tunneling driver
> you find all of them in my home at my work place.
> -> http://charm.itp.tuwien.ac.at/~mattems/
> happy to hear your feedback soon.
>
> a++ maks
>
>
> ps i test booted them, but in any case keep a working kernel
> in your lilo config. you'll may need to set up initrd symlinks..
I'm using grub so it shouldn't be an issue.
Reply to: