Re: Nuova scheda madre AS ROCK
Il 01/06/21 15:40, Davide Prina ha scritto:
> On 01/06/21 10:26, pinguino wrote:
>
>> Ho visto però che ci sono due led uno da luce gialla lampeggiante e
>> l'altro ha una luce rossa accesa fissa.
>
> quando la luce della scheda di rete è rossa, allora ci sono problemi.
>
> Non è che nella tua rete casalinga ci sono più PC e per caso uno ha lo
> stesso IP della tua scheda di rete?
Buongiorno Lista,
Si, ho un tablet collegato con un adattatore ad una delle porte dell'Hag
di Fastweb. Ma non so come si fa per vedere l'Ip, se lo possiede.
O magari c'è qualcosa che non va
> nella tabella di routing
>
> prova così:
> metti il cavo in questa scheda di rete, verifica che il led sia rosso e
> recupera l'IP che ti è stato assegnato
>
> visualizza il tuo IP
> # ifconfig
>
> visualizza la tabella di routing
> # route
>
> Prova a rieseguire gli stessi comandi anche con il cavo nell'altra presa
> di rete
>
> Ciao
> Davide
Questi sono l'ifconfig ed il route della scheda Atheros:
ifconfig
enp1s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.157.147.183 netmask 255.255.240.0 broadcast 10.157.159.255
inet6 fe80::a70e:4225:da1f:382b prefixlen 64 scopeid 0x20<link>
ether d0:50:99:4f:f9:7a txqueuelen 1000 (Ethernet)
RX packets 40 bytes 7835 (7.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 78 bytes 11577 (11.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 18
enp2s8: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:11:95:65:cb:f6 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 14 bytes 2170 (2.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 14 bytes 2170 (2.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
default 10.157.144.1 0.0.0.0 UG 100 0 0
enp1s0
10.157.144.0 0.0.0.0 255.255.240.0 U 100 0 0
enp1s0
Questi sono della Dlink:
ifconfig
enp1s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether d0:50:99:4f:f9:7a txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 18
enp2s8: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.157.147.181 netmask 255.255.240.0 broadcast 10.157.159.255
inet6 fe80::d66a:de4f:6157:27ff prefixlen 64 scopeid 0x20<link>
ether 00:11:95:65:cb:f6 txqueuelen 1000 (Ethernet)
RX packets 1098 bytes 966145 (943.5 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 916 bytes 100223 (97.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 14 bytes 2170 (2.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 14 bytes 2170 (2.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
default 10.157.144.1 0.0.0.0 UG 100 0 0
enp2s8
10.157.144.0 0.0.0.0 255.255.240.0 U 100 0 0
enp2s8
Grazie
Saluti
Reply to: