Re: impossibile sospendere o ibernare con dispositivo usb collegato
Il 16/09/2014 19:39, tarqui@aruba.it ha scritto:
> Il 16/09/2014 19:36, MaX ha scritto:
>> prova ad individuare quale modulo usb è il colpevole.
>> Poi fai una regola in /etc/pm/.... per lo sleep, hoberante e il
>> wake-up in cui rimuovi il modulo e poi al risveglio lo ricarichi di
>> nuovo.
provato con rmmod -f evdev ma si riattiva lo stesso.
ps
la lucina rossa del sensore del mouse (ottico) resta accesa.
estratto di dmesg (la versione completa a fine messaggio)
[ 956.887209] PM: Preparing system for mem sleep
[ 956.916090] PM: Entering mem sleep
!! [ 956.922402] i8042 kbd 00:07: wake-up capability enabled by ACPI
[ 957.271230] sd 0:0:0:0: [sda] Stopping disk
[ 957.696082] PM: suspend of devices complete after 779.858 msecs
!! [ 957.728080] ehci_hcd 0000:00:02.1: wake-up capability enabled by ACPI
!! [ 957.744067] ohci_hcd 0000:00:02.0: wake-up capability enabled by ACPI
[ 957.760126] PM: late suspend of devices complete after 64.037 msecs
[ 957.760188] ACPI: Preparing to enter system sleep state S3
[ 958.160508] PM: Saving platform NVS memory
[ 958.160774] Disabling non-boot CPUs ...
[ 958.264024] CPU 1 is now offline
[ 958.264508] ACPI: Low-level resume complete
...
che diavolo è i8042?
e perché diavolo acpi riattiva il wake-up sulle porte usb?
rimosso acpi*
riavvio
niente. come prima. sgrunt!
--
versione completa dmesg
[ 955.155631] wlan0: deauthenticating from 00:0c:42:6a:b2:39 by local
choice (reason=3)
[ 955.166149] cfg80211: Calling CRDA to update world regulatory domain
[ 955.211126] cfg80211: World regulatory domain updated:
[ 955.211129] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 955.211132] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 955.211134] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 955.211136] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm)
[ 955.211138] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz),
(N/A, 2000 mBm)
[ 955.211140] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm)
[ 955.211142] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000
KHz), (N/A, 0 mBm)
[ 956.859419] PM: Syncing filesystems ... done.
[ 956.887209] PM: Preparing system for mem sleep
[ 956.887222] Freezing user space processes ... (elapsed 0.01 seconds)
done.
[ 956.900089] Freezing remaining freezable tasks ... (elapsed 0.01
seconds) done.
[ 956.916090] PM: Entering mem sleep
[ 956.916120] Suspending console(s) (use no_console_suspend to debug)
[ 956.916312] sd 2:0:0:0: [sdb] Synchronizing SCSI cache
[ 956.916425] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 956.916522] sd 2:0:0:0: [sdb] Stopping disk
[ 956.922206] serial 00:08: disabled
[ 956.922212] serial 00:08: wake-up capability disabled by ACPI
[ 956.922402] i8042 kbd 00:07: wake-up capability enabled by ACPI
[ 957.271230] sd 0:0:0:0: [sda] Stopping disk
[ 957.696082] PM: suspend of devices complete after 779.858 msecs
[ 957.728080] ehci_hcd 0000:00:02.1: wake-up capability enabled by ACPI
[ 957.744067] ohci_hcd 0000:00:02.0: wake-up capability enabled by ACPI
[ 957.760126] PM: late suspend of devices complete after 64.037 msecs
[ 957.760188] ACPI: Preparing to enter system sleep state S3
[ 958.160508] PM: Saving platform NVS memory
[ 958.160774] Disabling non-boot CPUs ...
[ 958.264024] CPU 1 is now offline
[ 958.264508] ACPI: Low-level resume complete
[ 958.264508] PM: Restoring platform NVS memory
[ 958.264508] PCI-DMA: Resuming GART IOMMU
[ 958.264508] PCI-DMA: Restoring GART aperture settings
[ 958.264508] Enabling non-boot CPUs ...
[ 958.264508] Booting Node 0 Processor 1 APIC 0x1
[ 958.264508] smpboot cpu 1: start_ip = 9a000
[ 958.162149] Calibrating delay loop (skipped) already calibrated this CPU
[ 958.162149] [Firmware Bug]: cpu 1, try to use APIC500 (LVT offset 0)
for vector 0x400, but the register is already in use for vector 0xf9 on
another cpu
[ 958.162149] perf: IBS APIC setup failed on cpu #1
[ 958.296745] NMI watchdog enabled, takes one hw-pmu counter.
[ 958.300058] CPU1 is up
[ 958.300504] ACPI: Waking up from system sleep state S3
[ 958.301173] ohci_hcd 0000:00:02.0: wake-up capability disabled by ACPI
[ 958.301198] ehci_hcd 0000:00:02.1: wake-up capability disabled by ACPI
[ 958.301251] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301310] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301371] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301430] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301489] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301558] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301629] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301703] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 958.301811] PM: early resume of devices complete after 0.785 msecs
[ 958.301916] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 958.301934] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 958.301971] pci 0000:00:04.0: setting latency timer to 64
[ 958.302096] snd_hda_intel 0000:00:05.0: setting latency timer to 64
[ 958.302232] sata_nv 0000:00:08.0: setting latency timer to 64
[ 958.302245] sata_nv 0000:00:08.1: setting latency timer to 64
[ 958.302548] sd 0:0:0:0: [sda] Starting disk
[ 958.302576] sd 2:0:0:0: [sdb] Starting disk
[ 958.303118] i8042 kbd 00:07: wake-up capability disabled by ACPI
[ 958.303638] serial 00:08: activated
[ 958.768083] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 958.768171] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 958.768250] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 958.776210] ata3.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES)
filtered out
[ 958.776263] ata4.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES)
filtered out
[ 958.792243] ata4.00: configured for UDMA/100
[ 958.792399] ata3.00: configured for UDMA/133
[ 958.800191] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES)
filtered out
[ 958.813056] ata1.00: configured for UDMA/133
[ 958.832065] usb 2-8: reset low-speed USB device number 3 using ohci_hcd
[ 959.034284] ata2: SATA link down (SStatus 0 SControl 300)
[ 959.190151] PM: resume of devices complete after 888.299 msecs
[ 959.190303] PM: Finishing wakeup.
[ 959.190304] Restarting tasks ... done.
[ 962.892325] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 962.907376] forcedeth 0000:00:07.0: irq 43 for MSI/MSI-X
[ 962.907571] forcedeth 0000:00:07.0: eth0: no link during initialization
[ 962.912718] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 964.652073] wlan0: authenticate with 00:0c:42:6a:b2:39 (try 1)
[ 964.653558] wlan0: authenticated
[ 964.653850] wlan0: associate with 00:0c:42:6a:b2:39 (try 1)
[ 964.658051] wlan0: RX AssocResp from 00:0c:42:6a:b2:39 (capab=0x421
status=0 aid=2)
[ 964.658054] wlan0: associated
[ 964.658846] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Reply to: