Re: Errore su FAT
>-- Messaggio originale --
>Date: Thu, 24 Mar 2005 09:38:29 +0100
>From: Carlo Agrusti <carlo-ag@libero.it>
>Hai provato a montare /dev/sda? Questa è la riga del mio fstab:
>
>/dev/sda /media/usb vfat rw,user,sync,noauto 0 0
Quando inserisco la chiave ottengo questi messaggi dal kernel:
ohci_hcd 0001:10:18.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC
PPS PES CCS
usb 1-1: new full speed USB device using ohci_hcd and address 4
ohci_hcd 0001:10:18.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC
PPS PES CCS
usb 1-1: skipped 1 descriptor after endpoint
usb 1-1: new device strings: Mfr=1, Product=3, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: USB Embedded Hub
usb 1-1: Manufacturer: USB 2.0 Flash Disk
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 1 port detected
hub 1-1:1.0: compound device; port removable status: F
hub 1-1:1.0: individual port power switching
hub 1-1:1.0: individual port over-current protection
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is lost (inactive)
hub 1-1:1.0: enabling power on all ports
hub 1-1:1.0: state 5 ports 1 chg 0002 evt 0003
hub 1-1:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 1-1.1: new full speed USB device using ohci_hcd and address 5
usb 1-1.1: new device strings: Mfr=1, Product=4, SerialNumber=0
usb 1-1.1: default language 0x0409
usb 1-1.1: Product: USB Mass Storage Device
usb 1-1.1: Manufacturer: USB 2.0 Flash Disk
usb 1-1.1: hotplug
usb 1-1.1: adding 1-1.1:1.0 (config #1, interface 0)
usb 1-1.1:1.0: hotplug
usb-storage 1-1.1:1.0: usb_probe_interface
usb-storage 1-1.1:1.0: usb_probe_interface - got id
scsi1 : SCSI emulation for USB Mass Storage devices
hub 1-1:1.0: state 5 ports 1 chg 0000 evt 0002
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Flash Disk Rev: PROL
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
/dev/scsi/host1/bus0/target0/lun0: unknown partition table
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
usb-storage: device scan complete
Se tento di montare /dev/sda:
debibook:~# mount -t vfat /dev/sda /mnt/usbpen/
mount: wrong fs type, bad option, bad superblock on /dev/sda,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
E dal kernel ottengo:
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda.
Manca qualcosa al mio kernel?
Ora provo a formattare la chiavetta su questo pc sempre in fat.
Grazie a tutti
Reply to: