[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: boot con errore per hd aggiunto



On lun, 2004-04-26 at 04:43, Ercole wrote:
> Salve a tutti
> ho un altro problema ho aggiunto un hd estraibile di 4,1 Gb
> 
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ALI15X3: IDE controller at PCI slot 00:0b.0
> ALI15X3: chipset revision 32
> ALI15X3: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
>     ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
> hda: Maxtor 6Y080L0, ATA DISK drive
> blk: queue c03a9d80, I/O limit 4095Mb (mask 0xffffffff)
> hdc: ASUS CRW-5232AS, ATAPI CD/DVD-ROM drive
> hdd: QUANTUM FIREBALL ST4.3A, ATA DISK drive
> blk: queue c03aa310, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: attached ide-disk driver.
> hda: host protected area => 1
> hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=9964/255/63, (U)DMA
> hdd: attached ide-disk driver.
> hdd: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> hdd: task_no_data_intr: error=0x04 { DriveStatusError }
> hdd: 8418816 sectors (4310 MB) w/81KiB Cache, CHS=14848/9/63, (U)DMA
> Partition check:
>  hda: hda1 hda2 < hda5 hda6 >
>  hdd: hdd1 hdd2
> 
> Drivestatuserror.... che succede?

ti consiglio di ricompilare il kernel:
vedi di selezionare la seguente direttiva:

Use multi-mode by default

dall'help:
	CONFIG_IDEDISK_MULTI_MODE:                                                                                                                                   	If you get this error, try to say Y here:
		hda: set_multmode: status=0x51 { DriveReady SeekComplete 		Error}
		hda: set_multmode: error=0x04 { DriveStatusError }



> 
> altro problema
> per portare il sistembus a 66mhz cosa devo fare?
> la mia skeda madre è a 66mhz overclokkata a 75mhz

da dmesg puoi estrapolare:
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx

quindi, all'avvio, passi come parametro
idebus=66

(ovviamente, dopo aver verificato il corretto funzionamento, potrai
inserire in /etc/lilo.conf la stringa 
append = "idebus=66"


> 
> - Ercole -
> 
> Siete la mia 2° famiglia senza di voi sarei perso e forse nn avrei assaporato 
> le bellezze del linux, forse lo avrei abbandonato.. 
> adesso mi sento libero!
concordo pienamente: la ML è Stupenda ^_^


> Grazie vivamente
> Grazie

CiAU!

-- 
MaXeR

Attachment: signature.asc
Description: This is a digitally signed message part


Reply to: