random freezes B2000 running debian hppa lenny
hello,
My hppa box (B2000) experiences some problems: it freezes after a few
(2-6) hours.
On the led display I get the following error codes:
FLT CBFC: SYS BD
bus timeout
OS HPMC bz err
Bad OS HPMC len
HPMC initiated
I don't have screen nor keyboard attached to it so debugging is a bit
difficult.
System:
Debian lenny (stable), rather clean install
$ uname -a
Linux coulomb 2.6.26-2-parisc #1 Fri Mar 27 03:29:17 UTC 2009 parisc
GNU/Linux
The machines has the following lspci:
00:0c.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev 41)
00:0d.0 Multimedia audio controller: Analog Devices AD1889 sound chip
00:0e.0 IDE interface: National Semiconductor Corporation 87415/87560
IDE (rev 03)
00:0e.1 Bridge: National Semiconductor Corporation 87560 Legacy I/O (rev 01)
00:0e.2 USB Controller: National Semiconductor Corporation USB
Controller (rev 02)
00:0f.0 SCSI storage controller: LSI Logic / Symbios Logic 53c895a (rev 01)
01:00.0 3D controller: Hewlett-Packard Company Visualize FXe (rev 03)
01:04.0 Mass storage controller: Promise Technology, Inc. PDC40718 (SATA
300 TX4) (rev 02)
Of which the last entry might well be the problem.
This is a promise card for my 3* 1TB sata disks. They seem to be
initialized correctly, I made software raid with mdadm, but not I get
the following:
$ cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5]
[raid4] [raid10]
md0 : active raid5 sdc1[0] sde1[3] sdd1[1]
1953519872 blocks level 5, 64k chunk, algorithm 2 [3/2] [UU_]
[=>...................] recovery = 5.8% (56795292/976759936)
finish=451.9min speed=33920K/sec
unused devices: <none>
This keeps on running for a few hours, until the machine gets unresponsive.
I don't think I get anything strange in syslog, kernel.log, messages,...
So, my questions:
* Is this sata promise card the fault?
* on the web, the errors on the display seemed to indicate hardware
problems, but any insight on that?
* Best ways to solve this?
* Did I forget something?
Dirk
PS: Next thing I'll try is to remove the promise card to see if that was
the problem
PPS: dmesg in attach
--
Dirk Van Hertem Dirk.VanHertem@esat.kuleuven.be
Electrical Engineering Department http://www.esat.kuleuven.be/electa
K.U. Leuven, ESAT-ELECTA tel: +32-16-32.18.95
10, Kasteelpark Arenberg, B-3001 Heverlee fax: +32-16-32.19.85
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-parisc (Debian 2.6.26-15) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Fri Mar 27 03:29:17 UTC 2009
[ 0.000000] FP[0] enabled: Rev 1 Model 16
[ 0.000000] The 32-bit Kernel has started...
[ 0.000000] console [ttyB0] enabled
[ 0.000000] Initialized PDC Console for debugging.
[ 0.000000] Determining PDC firmware type: System Map.
[ 0.000000] model 00005d00 00000481 00000000 00000002 782d3480 100000f0 00000008 000000b2 000000b2
[ 0.000000] vers 00000301
[ 0.000000] CPUID vers 17 rev 11 (0x0000022b)
[ 0.000000] capabilities 0x3
[ 0.000000] model 9000/785/B2000
[ 0.000000] Total Memory: 1024 MB
[ 0.000000] initrd: 4f8ce000-4ffedfb5
[ 0.000000] initrd: reserving 3f8ce000-3ffedfb5 (mem_max 40000000)
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] Normal zone: 2048 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 260096 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] LCD display at f05d0008,f05d0000 registered
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
[ 0.000000] Kernel command line: root=/dev/sdb5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Console: colour dummy device 160x64
[17179569.248000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179569.348000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179569.532000] Memory: 1026560k/1048576k available (1961k kernel code, 21792k reserved, 882k data, 224k init)
[17179569.660000] virtual kernel memory layout:
[17179569.660000] vmalloc : 0x00008000 - 0x0f000000 ( 239 MB)
[17179569.660000] memory : 0x10000000 - 0x50000000 (1024 MB)
[17179569.660000] .init : 0x10410000 - 0x10448000 ( 224 kB)
[17179569.660000] .data : 0x102ea6b4 - 0x103c7000 ( 882 kB)
[17179569.660000] .text : 0x10100000 - 0x102ea6b4 (1961 kB)
[17179570.112000] Calibrating delay loop... 798.72 BogoMIPS (lpj=1597440)
[17179570.204000] Security Framework initialized
[17179570.260000] SELinux: Disabled at boot.
[17179570.312000] Capability LSM initialized
[17179570.368000] Mount-cache hash table entries: 512
[17179570.428000] Initializing cgroup subsys ns
[17179570.484000] Initializing cgroup subsys cpuacct
[17179570.548000] Initializing cgroup subsys devices
[17179570.612000] net_namespace: 648 bytes
[17179570.660000] NET: Registered protocol family 16
[17179570.724000] EISA bus registered
[17179570.768000] Searching for devices...
[17179571.020000] Found devices:
[17179571.060000] 1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b }
[17179571.160000] 2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
[17179571.264000] 3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a }
[17179571.364000] 4. Kazoo W+ at 0xfffa0000 [32] { 0, 0x0, 0x5d0, 0x00004 }
[17179571.452000] 5. Memory at 0xfed10200 [49] { 1, 0x0, 0x09d, 0x00009 }
[17179571.536000] Enabling regular chassis codes support v0.05
[17179571.736000] CPU(s): 1 x PA8600 (PCX-W+) at 400.000000 MHz
[17179571.812000] Whole cache flush 115727 cycles, flushing 3440640 bytes 467519 cycles
[17179571.812000] Setting cache flush threshold to 1980 (1 CPUs online)
[17179571.920000] SBA found Astro 2.1 at 0xfed00000
[17179571.984000] Elroy version TR4.0 (0x5) found at 0xfed30000
[17179572.060000] PCI: Enabled native mode for NS87415 (pif=0x8f)
[17179572.140000] Elroy version TR4.0 (0x5) found at 0xfed32000
[17179572.232000] powersw: Soft power switch at 0xf0400804 enabled.
[17179572.324000] NET: Registered protocol family 2
[17179572.424000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179572.520000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[17179572.624000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[17179572.716000] TCP: Hash tables configured (established 131072 bind 65536)
[17179572.808000] TCP reno registered
[17179572.864000] NET: Registered protocol family 1
[17179572.924000] checking if image is initramfs... it is
[17179575.908000] Freeing initrd memory: 7295k freed
[17179575.976000] Enabling PDC chassis warnings support v0.05
[17179576.048000] unwind_init: start = 0x1035de10, end = 0x103850f0, entries = 10030
[17179576.144000] WARNING: Out of order unwind entry! 1035f810 and 1035f820
[17179576.232000] WARNING: Out of order unwind entry! 1035f820 and 1035f830
[17179576.324000] audit: initializing netlink socket (disabled)
[17179576.396000] type=2000 audit(1241188257.212:1): initialized
[17179576.472000] VFS: Disk quotas dquot_6.5.1
[17179576.528000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179576.620000] msgmni has been set to 2019
[17179576.676000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[17179576.776000] io scheduler noop registered
[17179576.832000] io scheduler anticipatory registered
[17179576.896000] io scheduler deadline registered
[17179576.956000] io scheduler cfq registered (default)
[17179577.020000] SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 67)
[17179577.120000] SuperIO: Serial port 1 at 0x3f8
[17179577.176000] SuperIO: Serial port 2 at 0x2f8
[17179577.236000] SuperIO: Parallel port at 0x378
[17179577.292000] SuperIO: Floppy controller at 0x3f0
[17179577.356000] SuperIO: ACPI at 0x7e0
[17179577.404000] SuperIO: USB regulator enabled
[17179577.464000] PDC Stable Storage facility v0.30
[17179577.836000] STI GSC/PCI core graphics driver Version 0.9a
[17179577.912000] sti 0000:01:00.0: enabling SERR and PARITY (0046 -> 0146)
[17179578.000000] STI PCI graphic ROM found at f4840000 (128 kB), fb at fb000000 (16 MB)
[17179578.228000] id 35acda16-9a02587, conforms to spec rev. 8.0c
[17179578.312000] graphics card name: HPA4982A
[17179578.368000] sticon: Initializing STI text console.
[17179578.436000] Console: switching to colour STI console 160x64
[17179578.788000] stifb: 'HPA4982A' (id: 0x35acda16) not supported.
[17179578.876000] Generic RTC Driver v1.07
[17179578.928000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179579.036000] serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
[17179579.116000] console handover: boot [ttyB0] -> real [ttyS0]
[17179579.192000] serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
[17179579.276000] brd: module loaded
[17179579.316000] mice: PS/2 mouse device common for all mice
[17179579.384000] TCP cubic registered
[17179579.424000] NET: Registered protocol family 17
[17179579.484000] registered taskstats version 1
[17179579.536000] Freeing unused kernel memory: 224k freed
[17179580.348000] SCSI subsystem initialized
[17179581.996000] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
[17179582.080000] tulip0: no phy info, aborting mtable build
[17179582.144000] tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1.
[17179582.248000] eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xf4005000, 00:30:6e:08:0a:7f, IRQ 65.
[17179582.544000] usbcore: registered new interface driver usbfs
[17179582.612000] usbcore: registered new interface driver hub
[17179582.704000] sym0: <895a> rev 0x1 at pci 0000:00:0f.0 irq 68
[17179582.804000] libata version 3.00 loaded.
[17179582.824000] sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
[17179582.904000] sym0: SCSI BUS has been reset.
[17179582.964000] scsi0 : sym-2.2.3
[17179583.008000] usbcore: registered new device driver usb
[17179583.096000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[17179583.096000] ohci_hcd: block sizes: ed 64 td 64
[17179583.100000] ohci_hcd 0000:00:0e.2: OHCI Host Controller
[17179583.168000] ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
[17179583.260000] ohci_hcd 0000:00:0e.2: Using NSC SuperIO setup
[17179583.260000] ohci_hcd 0000:00:0e.2: created debug files
[17179583.260000] ohci_hcd 0000:00:0e.2: irq 1, io mem 0xf4004000
[17179583.384000] ohci_hcd 0000:00:0e.2: OHCI controller state
[17179583.384000] ohci_hcd 0000:00:0e.2: OHCI 1.0, NO legacy support registers
[17179583.384000] ohci_hcd 0000:00:0e.2: control 0x083 HCFS=operational CBSR=3
[17179583.384000] ohci_hcd 0000:00:0e.2: cmdstatus 0x00000 SOC=0
[17179583.384000] ohci_hcd 0000:00:0e.2: intrstatus 0x00000000
[17179583.384000] ohci_hcd 0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH
[17179583.384000] ohci_hcd 0000:00:0e.2: hcca frame #0000
[17179583.384000] ohci_hcd 0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3(3)
[17179583.384000] ohci_hcd 0000:00:0e.2: roothub.b 000e0000 PPCM=000e DR=0000
[17179583.384000] ohci_hcd 0000:00:0e.2: roothub.status 00008000 DRWE
[17179583.384000] ohci_hcd 0000:00:0e.2: roothub.portstatus [0] 0x00000100 PPS
[17179583.384000] ohci_hcd 0000:00:0e.2: roothub.portstatus [1] 0x00000100 PPS
[17179583.384000] ohci_hcd 0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS
[17179583.384000] usb usb1: default language 0x0409
[17179583.384000] usb usb1: uevent
[17179583.384000] usb usb1: usb_probe_device
[17179583.384000] usb usb1: configuration #1 chosen from 1 choice
[17179583.452000] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[17179583.452000] usb 1-0:1.0: uevent
[17179583.452000] hub 1-0:1.0: usb_probe_interface
[17179583.452000] hub 1-0:1.0: usb_probe_interface - got id
[17179583.452000] hub 1-0:1.0: USB hub found
[17179583.500000] hub 1-0:1.0: 3 ports detected
[17179583.552000] hub 1-0:1.0: standalone hub
[17179583.552000] hub 1-0:1.0: ganged power switching
[17179583.552000] hub 1-0:1.0: no over-current protection
[17179583.552000] hub 1-0:1.0: power on to power good time: 0ms
[17179583.552000] hub 1-0:1.0: local power source is good
[17179583.552000] hub 1-0:1.0: enabling power on all ports
[17179583.656000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[17179583.740000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[17179583.828000] usb usb1: Product: OHCI Host Controller
[17179583.892000] usb usb1: Manufacturer: Linux 2.6.26-2-parisc ohci_hcd
[17179583.968000] usb usb1: SerialNumber: 0000:00:0e.2
[17179584.032000] sata_promise 0000:01:04.0: version 2.12
[17179584.032000] scsi1 : sata_promise
[17179584.112000] Uniform Multi-Platform E-IDE driver
[17179584.168000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179584.268000] scsi2 : sata_promise
[17179584.312000] scsi3 : sata_promise
[17179584.352000] scsi4 : sata_promise
[17179584.396000] ata1: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820380 irq 70
[17179584.484000] ata2: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820280 irq 70
[17179584.576000] ata3: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820200 irq 70
[17179584.668000] ata4: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820300 irq 70
[17179584.760000] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[17179584.792000] NS87415: IDE controller (0x100b:0x0002 rev 0x03) at PCI slot 0000:00:0e.0
[17179584.892000] NS87415: 100% native mode on irq 7
[17179584.948000] ide0: BM-DMA at 0x0900-0x0907
[17179585.008000] ide1: BM-DMA at 0x0908-0x090f
[17179585.060000] Probing IDE interface ide0...
[17179585.184000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[17179585.284000] ata1.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133
[17179585.368000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[17179585.468000] ata1.00: configured for UDMA/133
[17179585.692000] hda: FX4830T, ATAPI CD/DVD-ROM drive
[17179585.856000] ata2: SATA link down (SStatus 0 SControl 300)
[17179586.240000] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[17179586.340000] ata3.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133
[17179586.424000] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[17179586.524000] ata3.00: configured for UDMA/133
[17179586.692000] Probing IDE interface ide1...
[17179586.896000] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[17179586.996000] ata4.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133
[17179587.080000] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[17179587.180000] ata4.00: configured for UDMA/133
[17179587.232000] scsi: waiting for bus probes to complete ...
[17179587.524000] ide0 at 0xe00-0xe07,0xd02 on irq 7
[17179587.580000] ide1 at 0xb00-0xb07,0xa02 on irq 7
[17179587.636000] scsi 0:0:5:0: Direct-Access IBM IC35L073UCDY10-0 S27T PQ: 0 ANSI: 3
[17179587.736000] target0:0:5: tagged command queuing enabled, command queue depth 16.
[17179587.828000] target0:0:5: Beginning Domain Validation
[17179587.892000] target0:0:5: asynchronous
[17179587.944000] target0:0:5: wide asynchronous
[17179587.996000] target0:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
[17179588.084000] target0:0:5: Domain Validation skipping write tests
[17179588.160000] target0:0:5: Ending Domain Validation
[17179588.220000] scsi 0:0:6:0: Direct-Access QUANTUM ATLAS5-9LVD HP04 PQ: 0 ANSI: 3
[17179588.320000] target0:0:6: tagged command queuing enabled, command queue depth 16.
[17179588.412000] target0:0:6: Beginning Domain Validation
[17179588.476000] target0:0:6: asynchronous
[17179588.528000] target0:0:6: wide asynchronous
[17179588.580000] target0:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
[17179588.668000] target0:0:6: Domain Validation skipping write tests
[17179588.744000] target0:0:6: Ending Domain Validation
[17179591.132000] scsi 1:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5
[17179591.304000] scsi 3:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5
[17179591.440000] Driver 'sd' needs updating - please use bus_type methods
[17179591.608000] scsi 4:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5
[17179591.732000] sd 0:0:5:0: [sda] 143374650 512-byte hardware sectors (73408 MB)
[17179592.108000] sd 0:0:5:0: [sda] Write Protect is off
[17179592.168000] sd 0:0:5:0: [sda] Mode Sense: cb 00 00 08
[17179592.296000] hda: ATAPI 48X CD-ROM drive, 128kB Cache
[17179592.356000] Uniform CD-ROM driver Revision: 3.20
[17179592.524000] sd 0:0:5:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[17179592.640000] sd 0:0:5:0: [sda] 143374650 512-byte hardware sectors (73408 MB)
[17179592.728000] sd 0:0:5:0: [sda] Write Protect is off
[17179592.788000] sd 0:0:5:0: [sda] Mode Sense: cb 00 00 08
[17179592.788000] sd 0:0:5:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[17179592.904000] sda: sda1
[17179592.964000] sd 0:0:5:0: [sda] Attached SCSI disk
[17179593.044000] sd 0:0:6:0: [sdb] 17773524 512-byte hardware sectors (9100 MB)
[17179593.140000] sd 0:0:6:0: [sdb] Write Protect is off
[17179593.204000] sd 0:0:6:0: [sdb] Mode Sense: e3 00 10 08
[17179593.232000] sd 0:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[17179593.348000] sd 0:0:6:0: [sdb] 17773524 512-byte hardware sectors (9100 MB)
[17179593.432000] sd 0:0:6:0: [sdb] Write Protect is off
[17179593.496000] sd 0:0:6:0: [sdb] Mode Sense: e3 00 10 08
[17179593.496000] sd 0:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[17179593.600000] sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 sdb8 > sdb4
[17179593.724000] sd 0:0:6:0: [sdb] Attached SCSI disk
[17179593.792000] sd 1:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
[17179593.884000] sd 1:0:0:0: [sdc] Write Protect is off
[17179593.944000] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[17179593.944000] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[17179594.056000] sd 1:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB)
[17179594.148000] sd 1:0:0:0: [sdc] Write Protect is off
[17179594.208000] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[17179594.208000] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[17179594.320000] sdc: sdc1
[17179594.364000] sd 1:0:0:0: [sdc] Attached SCSI disk
[17179594.432000] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors (1000205 MB)
[17179594.520000] sd 3:0:0:0: [sdd] Write Protect is off
[17179594.584000] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[17179594.584000] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[17179594.696000] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors (1000205 MB)
[17179594.784000] sd 3:0:0:0: [sdd] Write Protect is off
[17179594.844000] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[17179594.844000] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[17179594.956000] sdd: sdd1
[17179595.004000] sd 3:0:0:0: [sdd] Attached SCSI disk
[17179595.068000] sd 4:0:0:0: [sde] 1953525168 512-byte hardware sectors (1000205 MB)
[17179595.160000] sd 4:0:0:0: [sde] Write Protect is off
[17179595.220000] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[17179595.220000] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[17179595.332000] sd 4:0:0:0: [sde] 1953525168 512-byte hardware sectors (1000205 MB)
[17179595.424000] sd 4:0:0:0: [sde] Write Protect is off
[17179595.484000] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[17179595.484000] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[17179595.596000] sde: sde1
[17179595.640000] sd 4:0:0:0: [sde] Attached SCSI disk
[17179596.980000] md: linear personality registered for level -1
[17179597.088000] md: multipath personality registered for level -4
[17179597.200000] md: raid0 personality registered for level 0
[17179597.312000] md: raid1 personality registered for level 1
[17179597.416000] xor: measuring software checksum speed
[17179597.496000] 8regs : 943.000 MB/sec
[17179597.568000] 8regs_prefetch: 933.000 MB/sec
[17179597.644000] 32regs : 960.000 MB/sec
[17179597.716000] 32regs_prefetch: 945.000 MB/sec
[17179597.772000] xor: using function: 32regs (960.000 MB/sec)
[17179597.848000] async_tx: api initialized (sync-only)
[17179598.012000] raid6: int32x1 183 MB/s
[17179598.128000] raid6: int32x2 230 MB/s
[17179598.244000] raid6: int32x4 272 MB/s
[17179598.360000] raid6: int32x8 213 MB/s
[17179598.408000] raid6: using algorithm int32x4 (272 MB/s)
[17179598.468000] md: raid6 personality registered for level 6
[17179598.536000] md: raid5 personality registered for level 5
[17179598.604000] md: raid4 personality registered for level 4
[17179598.896000] md: raid10 personality registered for level 10
[17179599.136000] md: bind<sdd1>
[17179599.172000] md: bind<sde1>
[17179599.208000] md: bind<sdc1>
[17179599.324000] raid5: device sdc1 operational as raid disk 0
[17179599.392000] raid5: device sdd1 operational as raid disk 1
[17179599.460000] raid5: allocated 3176kB for md0
[17179599.512000] raid5: raid level 5 set md0 active with 2 out of 3 devices, algorithm 2
[17179599.608000] RAID5 conf printout:
[17179599.648000] --- rd:3 wd:2
[17179599.684000] disk 0, o:1, dev:sdc1
[17179599.728000] disk 1, o:1, dev:sdd1
[17179600.672000] EXT3-fs: INFO: recovery required on readonly filesystem.
[17179600.752000] EXT3-fs: write access will be enabled during recovery.
[17179601.128000] kjournald starting. Commit interval 5 seconds
[17179601.196000] EXT3-fs: recovery complete.
[17179601.244000] EXT3-fs: mounted filesystem with ordered data mode.
[17179603.920000] udevd version 125 started
[17179604.124000] usb usb1: uevent
[17179604.124000] usb 1-0:1.0: uevent
[17179609.280000] Adding 489940k swap on /dev/sdb7. Priority:-1 extents:1 across:489940k
[17179609.764000] EXT3 FS on sdb5, internal journal
[17179610.860000] LASI 82596 driver - Revision: 1.30
[17179610.980000] loop: module loaded
[17179616.900000] RAID5 conf printout:
[17179616.944000] --- rd:3 wd:2
[17179616.980000] disk 0, o:1, dev:sdc1
[17179617.024000] disk 1, o:1, dev:sdd1
[17179617.072000] disk 2, o:1, dev:sde1
[17179617.116000] md: recovery of RAID array md0
[17179617.168000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[17179617.240000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[17179617.360000] md: using 128k window, over a total of 976759936 blocks.
[17179632.056000] kjournald starting. Commit interval 5 seconds
[17179632.140000] EXT3 FS on sdb8, internal journal
[17179632.196000] EXT3-fs: mounted filesystem with ordered data mode.
[17179632.312000] kjournald starting. Commit interval 5 seconds
[17179632.392000] EXT3 FS on sdb4, internal journal
[17179632.448000] EXT3-fs: mounted filesystem with ordered data mode.
[17179632.556000] kjournald starting. Commit interval 5 seconds
[17179632.632000] EXT3 FS on sdb6, internal journal
[17179632.688000] EXT3-fs: mounted filesystem with ordered data mode.
[17179632.816000] kjournald starting. Commit interval 5 seconds
[17179632.920000] EXT3 FS on sda1, internal journal
[17179632.976000] EXT3-fs: mounted filesystem with ordered data mode.
[17179633.408000] kjournald starting. Commit interval 5 seconds
[17179633.512000] EXT3 FS on md0, internal journal
[17179633.564000] EXT3-fs: mounted filesystem with ordered data mode.
[17179639.712000] eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
Reply to: