Kernel panic after upgrade from 2.6.22-1 to 2.6.24-1
Hello,
today I upgraded my HP9000 running debian lenny/sid.
Mostly all went well.
Unfortunatly after reboot the kernel panics.
I append the boot log, so if one can figure out what happens and what to
repair, it might help all of us running hppa machines.
Greetings to all, Jürgen Leibner
Firmware Version 36.34
Duplex Console IO Dependent Code (IODC) revision 0
------------------------------------------------------------------------------
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State Cache Size
--------- -------- --------------------- ----------------- ----------
0 120 MHz Active Functional 1 MB
1 120 MHz Idle Functional 1 MB
Central Bus Speed (in MHz) : 120
Available memory (bytes) : 536870912
Good memory required (bytes): 22618112
Primary boot path: 8/8.5 (dec)
Alternate boot path: 8/16/5.2 (dec)
Console path: 8/16/4.0 (dec)
Keyboard path: 8/16/7.0 (dec)
CPU 0
WARNING: Memory has been initialized, but not tested as a result of
FASTBOOT being enabled. To test memory, use the FASTBOOT
command in the CONFIGURATION menu and reboot the system.
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
10 seconds expired.
Proceeding...
Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 7
HARD Booted.
palo ipl 1.14 root@duet Sat Apr 8 16:08:16 EDT 2006
Partition Start(MB) End(MB) Id Type
1 1 31 f0 Palo
2 32 156 83 ext2
5 157 1890 83 ext2
6 1891 2031 82 swap
PALO(F0) partition contains:
0/vmlinux32 4191629 bytes @ 0x48000
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux'
Selected kernel: /vmlinux from partition 2
Selected ramdisk: /initrd.img from partition 2
ELF32 executable
Entry 00100300 first 00100000 n 3
Segment 0 load 00100000 size 3206548 mediaptr 0x1000
Segment 1 load 0040f000 size 524288 mediaptr 0x310000
Segment 2 load 004cc000 size 263168 mediaptr 0x390000
Loading ramdisk 5669321 bytes @ 1fa86000...
Branching to kernel entry point 0x00100300. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Initializing cgroup subsys cpuset
Linux version 2.6.24-1-parisc-smp (Debian 2.6.24-5) (waldi@debian.org) (gcc version 4.1.3 20080308 (prerelease) (Debian 4.1.2-21)) #2 SMP Thu Mar 27 18:17:20 MDT 2008
FP[0] enabled: Rev 1 Model 11
The 32-bit Kernel has started...
console [ttyB0] enabled
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005a10 00000491 00000000 00000002 7768217e 100000f0 00000004 0000008a 0000008a
vers 0000000d
CPUID vers 11 rev 13 (0x0000016d)
model 9000/851/D360
Total Memory: 512 MB
initrd: 2fa86000-2ffee1c9
initrd: reserving 1fa86000-1ffee1c9 (mem_max 20000000)
SMP: bootstrap CPU ID is 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 508672k/524288k available (2619k kernel code, 15424k reserved, 1000k data, 244k init)
virtual kernel memory layout:
vmalloc : 0x00008000 - 0x0f000000 ( 239 MB)
memory : 0x10000000 - 0x30000000 ( 512 MB)
.init : 0x104d0000 - 0x1050d000 ( 244 kB)
.data : 0x1038ec0c - 0x10489000 (1000 kB)
.text : 0x10100000 - 0x1038ec0c (2619 kB)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Brought up 1 CPUs
net_namespace: 64 bytes
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0x7, 0x580, 0x0000b }
2. UL 550 Lasi Core BA at 0xffd00000 [8/16] { 11, 0x0, 0x02f, 0x00081 }, additional addresses: 0xffd0c000 0xffc00000
3. UL 550 Lasi Core RS-232 at 0xffd05000 [8/16/4] { 10, 0x0, 0x02f, 0x0008c }
4. UL 550 Core SCSI at 0xffd06000 [8/16/5] { 10, 0x0, 0x02f, 0x00082 }
5. UL 350 Core LAN (802.3) at 0xffd07000 [8/16/6] { 10, 0x0, 0x02f, 0x0008a }
6. UL 550 Core Centronics at 0xffd02000 [8/16/0] { 10, 0x0, 0x02f, 0x00074 }, additional addresses: 0xffd01000 0xffd03000
7. UL 550 Core PS/2 Port at 0xffd08000 [8/16/7] { 10, 0x0, 0x02f, 0x00084 }
8. UL 550 Core PS/2 Port at 0xffd08100 [8/16/8] { 10, 0x0, 0x02f, 0x00084 }
9. UL 550 Core Wax BA at 0xffe00000 [8/20] { 11, 0x0, 0x031, 0x0008e }
10. UL 550 Wax EISA BA at 0xfc000000 [8/20/5] { 11, 0x0, 0x031, 0x00090 }, additional addresses: 0xffc88000
11. UL 550 Wax Core RS-232 at 0xffe02000 [8/20/2] { 10, 0x0, 0x031, 0x0008c }
12. Bluefish Add-on FW-SCSI at 0xf1008000 [8/8] { 4, 0x1, 0x013, 0x00089 }
13. Bluefish Add-on FW-SCSI at 0xf100c000 [8/12] { 4, 0x1, 0x013, 0x00089 }
14. U2-IOA BC GSC+ Port at 0xf103f000 [8/63] { 7, 0x1, 0x501, 0x0000c }
15. U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0x7, 0x580, 0x0000b }
16. U2-IOA BC GSC+ Port at 0xf183f000 [10/63] { 7, 0x1, 0x501, 0x0000c }
17. UL 2w T120 1MB/1MB (851/D260,D360) at 0xfffa0000 [32] { 0, 0x0, 0x5a1, 0x00004 }
18. UL 2w T120 1MB/1MB (851/D260,D360) at 0xfffa2000 [34] { 0, 0x0, 0x5a1, 0x00004 }
19. Memory at 0xfffb1000 [49] { 1, 0x0, 0x073, 0x00009 }
Enabling regular chassis codes support v0.05
Releasing cpu 1 now, hpa=fffa2000
FP[1] enabled: Rev 1 Model 11
CPU(s): 2 x PA7200 (PCX-T') at 120.000000 MHz
Setting cache flush threshold to 420 (2 CPUs online)
Found U2 at 0xfff88000
Found U2 at 0xfff8a000
Lasi version 0 at 0xffd00000 found.
LED display at ffd0c000 registered
wax at 0xffe00000 found.
Wax EISA Adapter found at 0xfc000000
Enumerating EISA bus
EISA slot 8 a configured board was not detected ( expected HWP1510)
EISA: Probing bus 0 at 8:20:5
EISA: Mainboard HWPC051 detected.
EISA: Detected 0 cards.
Found GeckoBoa at 0xf103f000
drivers/parisc/hppb.c: failed to claim HP-PB bus space (00000000, ffffffff)
Found GeckoBoa at 0xf183f000
powersw: Soft power switch at 0xf0140000 enabled.
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5536k freed
Enabling PDC chassis warnings support v0.05
unwind_init: start = 0x10410e00, end = 0x1043caf0, entries = 11215
Backtrace:
[<104dc0a8>] init+0x24/0xfc
[<104d166c>] kernel_init+0x1cc/0x398
[<1010bc5c>] ret_from_kernel_thread+0x1c/0x24
Kernel Fault: Code=26 regs=2f4401c0 (Addr=00000000)
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001111111100001111 Not tainted
r00-03 0004ff0f 10152800 104dc0a8 104ee010
r04-07 1043d010 1050863c 00000000 00000000
r08-11 00000000 000000f0 0004000e 00000000
r12-15 1046b4b4 10102030 000000fd f0100000
r16-19 f0001180 f0000070 f0000068 2f440000
r20-23 00000000 2f41a090 104dc084 103d2e0b
r24-27 00000000 00000000 00000000 1043f010
r28-31 00000000 10024467 2f4401c0 104d166c
sr00-03 00000000 00000000 00000000 00000000
sr04-07 00000000 00000000 00000000 00000000
IASQ: 00000000 00000000 IAOQ: 10152d0c 10152d10
IIR: 0f401089 ISR: 00000000 IOR: 00000000
CPU: 0 CR30: 2f440000 CR31: f01043b0
ORIG_R28: 10473010
IAOQ[0]: cmpxchg_futex_value_locked+0x28/0x7c
IAOQ[1]: cmpxchg_futex_value_locked+0x2c/0x7c
RP(r2): init+0x24/0xfc
Kernel panic - not syncing: Kernel Fault
Reply to: