apt-cache causes freeze and aptitude a kernel panic on hp9000 d360/2 with fresh installed debian etch
Hello to all,
any hints to the following?
Firmware Version 36.34
Duplex Console IO Dependent Code (IODC) revision 0
------------------------------------------------------------------------------
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State Cache
Size
--------- -------- --------------------- ----------------- ----------
0 120 MHz Active Functional 1
MB
1 120 MHz Idle Functional 1
MB
Central Bus Speed (in MHz) : 120
Available memory (bytes) : 536870912
Good memory required (bytes): 22618112
Primary boot path: 8/8.5 (dec)
Alternate boot path: 8/16/5.2 (dec)
Console path: 8/16/4.0 (dec)
Keyboard path: 8/16/7.0 (dec)
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
10 seconds expired.
Proceeding...
Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 7
SOFT Booted.
palo ipl 1.14 root@duet Sat Apr 8 16:08:16 EDT 2006
Partition Start(MB) End(MB) Id Type
1 1 31 f0 Palo
2 32 156 83 ext2
5 157 1890 83 ext2
6 1891 2031 82 swap
PALO(F0) partition contains:
0/vmlinux32 4191629 bytes @ 0x48000
Information: No console specified on kernel command line. This is
normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102
palo_ke
rnel=2/vmlinux'
Selected kernel: /vmlinux from partition 2
Selected ramdisk: /initrd.img from partition 2
ELF32 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 2798268 mediaptr 0x1000
Segment 1 load 003ac000 size 532480 mediaptr 0x2ad000
Segment 2 load 0046c000 size 396292 mediaptr 0x32f000
Loading ramdisk 4742591 bytes @ 1fb68000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.18-5-parisc-smp (Debian 2.6.18.dfsg.1-13etch1)
(dannf@debian.o
rg) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP
Tue Aug 1
4 17:59:17 UTC 2007
FP[0] enabled: Rev 1 Model 11
The 32-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005a10 00000491 00000000 00000002 7768217e 100000f0 00000004
0000008a 00
00008a
vers 0000000d
CPUID vers 11 rev 13 (0x0000016d)
model 9000/851/D360
Total Memory: 512 MB
initrd: 2fb68000-2ffeddbf
initrd: reserving 1fb68000-1ffeddbf (mem_max 20000000)
SMP: bootstrap CPU ID is 0
Built 1 zonelists. Total pages: 131072
Kernel command line: root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102
palo_kernel=
2/vmlinux
PID hash table entries: 4096 (order: 12, 16384 bytes)
start_kernel(): bug: interrupts were enabled early
Console: colour dummy device 160x64
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 524288k available
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4631k freed
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0x7, 0x580, 0x0000b }
2. UL 550 Lasi Core BA at 0xffd00000 [8/16] { 11, 0x0, 0x02f, 0x00081 },
additio
nal addresses: 0xffd0c000 0xffc00000
3. UL 550 Lasi Core RS-232 at 0xffd05000 [8/16/4] { 10, 0x0, 0x02f,
0x0008c }
4. UL 550 Core SCSI at 0xffd06000 [8/16/5] { 10, 0x0, 0x02f, 0x00082 }
5. UL 350 Core LAN (802.3) at 0xffd07000 [8/16/6] { 10, 0x0, 0x02f,
0x0008a }
6. UL 550 Core Centronics at 0xffd02000 [8/16/0] { 10, 0x0, 0x02f,
0x00074 }, ad
ditional addresses: 0xffd01000 0xffd03000
7. UL 550 Core PS/2 Port at 0xffd08000 [8/16/7] { 10, 0x0, 0x02f,
0x00084 }
8. UL 550 Core PS/2 Port at 0xffd08100 [8/16/8] { 10, 0x0, 0x02f,
0x00084 }
9. UL 550 Core Wax BA at 0xffe00000 [8/20] { 11, 0x0, 0x031, 0x0008e }
10. UL 550 Wax EISA BA at 0xfc000000 [8/20/5] { 11, 0x0, 0x031,
0x00090 }, addit
ional addresses: 0xffc88000
11. UL 550 Wax Core RS-232 at 0xffe02000 [8/20/2] { 10, 0x0, 0x031,
0x0008c }
12. Bluefish Add-on FW-SCSI at 0xf1008000 [8/8] { 4, 0x1, 0x013,
0x00089 }
13. Bluefish Add-on FW-SCSI at 0xf100c000 [8/12] { 4, 0x1, 0x013,
0x00089 }
14. U2-IOA BC GSC+ Port at 0xf103f000 [8/63] { 7, 0x1, 0x501, 0x0000c }
15. U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0x7, 0x580, 0x0000b }
16. U2-IOA BC GSC+ Port at 0xf183f000 [10/63] { 7, 0x1, 0x501, 0x0000c }
17. UL 2w T120 1MB/1MB (851/D260,D360) at 0xfffa0000 [32] { 0, 0x0,
0x5a1, 0x000
04 }
18. UL 2w T120 1MB/1MB (851/D260,D360) at 0xfffa2000 [34] { 0, 0x0,
0x5a1, 0x000
04 }
19. Memory at 0xfffb1000 [49] { 1, 0x0, 0x073, 0x00009 }
Enabling regular chassis codes support v0.05
Releasing cpu 1 now, hpa=fffa2000
FP[1] enabled: Rev 1 Model 11
migration_cost=4000
CPU(s): 2 x PA7200 (PCX-T') at 120.000000 MHz
Setting cache flush threshold to 560 (2 CPUs online)
Found U2 at 0xfff88000
Found U2 at 0xfff8a000
Lasi version 0 at 0xffd00000 found.
LED display at ffd0c000 registered
wax at 0xffe00000 found.
Wax EISA Adapter found at 0xfc000000
Enumerating EISA bus
EISA slot 8 a configured board was not detected ( expected HWP1510)
EISA: Probing bus 0 at 8:20:5
EISA: Mainboard HWPC051 detected.
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 8, 1572864 bytes)
TCP bind hash table entries: 32768 (order: 7, 655360 bytes)
TCP: Hash tables configured (established 65536 bind 32768)
TCP reno registered
Enabling PDC chassis warnings support v0.05
unwind_init: start = 0x103adcc0, end = 0x103d39b0, entries = 9679
audit: initializing netlink socket (disabled)
audit(1187734700.368:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
EISA EEPROM at 0x0000c000
PDC Stable Storage facility v0.30
Soft power switch enabled, polling @ 0xf0140000.
STI GSC/PCI core graphics driver Version 0.9a
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
8:16:4: ttyS0 at MMIO 0xffd05800 (irq = 16) is a 16550A
8:20:2: ttyS1 at MMIO 0xffe02800 (irq = 23) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: GSC PS/2 keyboard port at 0x00020000 irq 20 @ 8:16:7
serio: GSC PS/2 mouse port at 0x00022100 irq 20 @ 8:16:8
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: BUG: warning at
arch/parisc/kernel/smp.c:350/smp_c
all_function()
Backtrace:
[<10115038>] smp_call_function+0x74/0x32c
[<10136834>] on_each_cpu+0x1c/0x50
[<10106c18>] free_initmem+0x48/0x1cc
[<10105f80>] init+0x288/0x35c
[<1010cc5c>] ret_from_kernel_thread+0x1c/0x24
340k freed
Loading, please wait...
Begin: Loading essential drivers... ...
SCSI subsystem initialized
53c700: Version 2.8 By James.Bottomley@HansenPartnership.com
scsi0: 53c710 rev 2
scsi0 : LASI SCSI 53c700
Vendor: HP Model: C1537A Rev: HP02
Type: Sequential-Access ANSI SCSI revision: 02
target0:0:0: Beginning Domain Validation
target0:0:0: asynchronous
target0:0:0: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 8)
target0:0:0: Domain Validation skipping write tests
target0:0:0: Ending Domain Validation
Vendor: TEAC Model: CD-ROM CD-516S Rev: 1.0G
Type: CD-ROM ANSI SCSI revision: 02
target0:0:2: Beginning Domain Validation
target0:0:2: asynchronous
target0:0:2: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 8)
target0:0:2: Domain Validation skipping write tests
target0:0:2: Ending Domain Validation
zalon_probe: Zalon version 1, IRQ 67
ncr53c720-0: rev 0xf irq 67
ncr53c720-0: ID 7, Fast-10, Parity Checking, Differential
scsi1 : ncr53c8xx-3.4.3g
Vendor: SEAGATE Model: ST32171W Rev: HPC1
Type: Direct-Access ANSI SCSI revision: 02
target1:0:5: Beginning Domain Validation
target1:0:5: asynchronous
target1:0:5: wide asynchronous
target1:0:5: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
target1:0:5: Domain Validation skipping write tests
target1:0:5: Ending Domain Validation
Vendor: SEAGATE Model: ST34572WC Rev: HP03
Type: Direct-Access ANSI SCSI revision: 02
target1:0:8: Beginning Domain Validation
target1:0:8: asynchronous
target1:0:8: wide asynchronous
target1:0:8: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
target1:0:8: Domain Validation skipping write tests
target1:0:8: Ending Domain Validation
Vendor: SEAGATE Model: ST34371W Rev: HPM2
Type: Direct-Access ANSI SCSI revision: 02
target1:0:9: Beginning Domain Validation
target1:0:9: asynchronous
target1:0:9: wide asynchronous
target1:0:9: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
target1:0:9: Domain Validation skipping write tests
target1:0:9: Ending Domain Validation
zalon_probe: Zalon version 1, IRQ 68
ncr53c720-1: rev 0xf irq 68
ncr53c720-1: ID 7, Fast-10, Parity Checking, Differential
scsi2 : ncr53c8xx-3.4.3g
Done.
Begin: Running /scripts/init-premount ...
SCSI device sda: 4165272 512-byte hdwr sectors (2133 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write through w/ FUA
SCSI device sda: 4165272 512-byte hdwr sectors (2133 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write through w/ FUA
sda: sda1 sda2 sda3 < sda5 sda6 >
sd 1:0:5:0: Attached scsi disk sda
SCSI device sdb: 8388314 512-byte hdwr sectors (4295 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write through w/ FUA
SCSI device sdb: 8388314 512-byte hdwr sectors (4295 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write through w/ FUA
sdb: sdb1
sd 1:0:8:0: Attached scsi disk sdb
SCSI device sdc: 8388314 512-byte hdwr sectors (4295 MB)
sdc: Write Protect is off
SCSI device sdc: drive cache: write through w/ FUA
SCSI device sdc: 8388314 512-byte hdwr sectors (4295 MB)
sdc: Write Protect is off
SCSI device sdc: drive cache: write through w/ FUA
sdc: sdc1
sd 1:0:9:0: Attached scsi disk sdc
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Done.
Begin: Running /scripts/local-premount ...
Done.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...st: Version 20050830, fixed
bufsize 326
st 0:0:0:0: Attached scsi tape st0
st0: try direct i/o: yes (alignment 512 B)
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
st 0:0:0:0: Attached scsi generic sg0 type 1
sr 0:0:2:0: Attached scsi generic sg1 type 5
sd 1:0:5:0: Attached scsi generic sg2 type 0
sd 1:0:8:0: Attached scsi generic sg3 type 0
sd 1:0:9:0: Attached scsi generic sg4 type 0
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 2f6307a0, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 2f6307a0
sr0: Hmm, seems the drive doesn't support multisession CD's
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 2f6307a0, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 2f6307a0
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 2f630200, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 2f630200
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 2ff3a720, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 2ff3a720
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 2f01fe40, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 2f01fe40
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 10aaa400, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 10aaa400
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 10aaa520, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 10aaa520
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 10aaa640, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 10aaa640
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 10aaaac0, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 10aaaac0
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_INhp9000 login:
root
Password:
Last login: Tue Aug 21 18:04:31 2007 on ttyS0
Linux hp9000 2.6.18-5-parisc-smp #1 SMP Tue Aug 14 17:59:17 UTC 2007
parisc
The programs included with the Debian GNU/Linux system are free
software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
hp9000:~# objdump/nm
-bash: objdump/nm: No such file or directory
hp9000:~# ping www.heise.de
PING www.heise.de (193.99.144.85) 56(84) bytes of data.
64 bytes from www.heise.de (193.99.144.85): icmp_seq=1 ttl=248 time=272
ms
64 bytes from www.heise.de (193.99.144.85): icmp_seq=2 ttl=248 time=276
ms
64 bytes from ww
--- www.heise.de ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 272.017/277.350/284.018/5.026 ms
hp9000:~# apt-cache search objdump
apt-cache(2002): unaligned access to 0x4109e094 at ip=0x40384a27
scsi0: Bus Reset detected, executing command 10aaabe0, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 10aaabe0
scsi0: (2:0) phase mismatch at 01e8, phase IO BSY DATA_IN
scsi0: Bus Reset detected, executing command 2f01fd20, slot 2f2a0520,
dsp 00080]
failing command because of reset, slot 2f2a0520, cmnd 2f01fd20
done.
Activating swap...Adding 144544k swap on /dev/sda6. Priority:-1
extents:1 acrok
done.
Checking root file system...fsck 1.40-WIP (14-Nov-2006)
/dev/sda5: clean, 20828/222208 files, 130300/443787 blocks
done.
EXT3 FS on sda5, internal journal
Setting the system clock..
Cleaning up ifupdown....
Loading kernel modules...LASI 82596 driver - Revision: 1.30
Found i82596 at 0xffd07000, IRQ 18
eth0: 82596 at 0xffd07000, 08 00 09 E7 D8 23 IRQ 18.
loop: loaded (max 8 devices)
done.
Loading device-mapper supportdevice-mapper: ioctl: 4.7.0-ioctl
(2006-06-24) inim
.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)
/dev/sda2 was not cleanly unmounted, check forced.
/dev/sda2: 23/64256 files (17.4% non-contiguous), 27424/128520 blocks
fsck died with exit status 1
done.
Setting kernel variables...done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...eth0: link ok.
done.
Starting portmap daemon....
Setting console screen modes and fonts.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting portmap daemon...Already running..
Starting MTA: exim4.
Starting internet superserver: inetd.
Starting NFS common utilities: statd.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: crond.
Debian GNU/Linux 4.0 hp9000 ttyS0
hp9000 login: root
Password:
Last login: Tue Aug 21 18:04:31 2007 on ttyS0
Linux hp9000 2.6.18-5-parisc-smp #1 SMP Tue Aug 14 17:59:17 UTC 2007
parisc
The programs included with the Debian GNU/Linux system are free
software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
hp9000:~# objdump/nm
-bash: objdump/nm: No such file or directory
hp9000:~# ping www.heise.de
PING www.heise.de (193.99.144.85) 56(84) bytes of data.
64 bytes from www.heise.de (193.99.144.85): icmp_seq=1 ttl=248 time=272
ms
64 bytes from www.heise.de (193.99.144.85): icmp_seq=2 ttl=248 time=276
ms
64 bytes from ww
--- www.heise.de ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 272.017/277.350/284.018/5.026 ms
hp9000:~# apt-cache search objdump
apt-cache(2002): unaligned access to 0x4109e094 at ip=0x40384a27
hp9000:~# aptitude install screen
Reading packageaptitude(2000): unaligned access to 0x4127e094 at
ip=0x40787a27
Backtrace:0%
[<101135c4>] L34+0x1c/0x84
[<101093c4>] handle_interruption+0x404/0x59c
[<1010d090>] intr_check_sig+0x0/0xc
Unexpected interruption: Code=20 regs=2ebd4d00 (Addr=00000000)
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001000000000000001111 Not tainted
r00-03 0004000f 00000000 101135c4 2ebd47c0
r04-07 2ebd47c0 4127e094 00000000 003668d8
r08-11 4127e094 001e1940 c004da4c c004dd48
r12-15 00364ce8 00000001 c004da28 c004da4c
r16-19 2ebd47c0 0036011c 00000000 00000000
r20-23 0000016a 00020d33 0000016a 50dce600
r24-27 00000000 0000016a 2ebd47c0 103d5010
r28-31 4127e094 2ebd47c0 2ebd4d00 00000a05
sr00-03 00000000 00000a05 00000000 00000a05
sr04-07 00000000 00000000 00000000 00000000
IASQ: 00000000 00000000 IAOQ: 10113038 1011303c
IIR: 0f945280 ISR: 00000a05 IOR: 4127e094
CPU: 0 CR30: 2ebd0000 CR31: 10470000
ORIG_R28: 00000000
IAOQ[0]: emulate_stw+0x5c/0x68
IAOQ[1]: emulate_stw+0x60/0x68
RP(r2): L34+0x1c/0x84
Kernel panic - not syncing: Unexpected interruption
Greetings, Jürgen
Reply to: