--- Begin Message ---
- To: Joel Soete <jsoe0708@tiscali.be>
- Subject: RE: Problem installing on HP RP5400
- From: James Morris <jmorris@photonicmaterials.com>
- Date: Tue, 18 May 2004 14:11:07 -0100 (GMT-01:00)
- Message-id: <3781944.1084893056327.SLOX.WebMail.wwwrun@mailserver.photonicmaterials.com>
- References: <409BA51F00006B9D@ocpmta1.freegates.net>
Hi joel I have downloaded the debian 3 rc2, done the checks etc and get the following output on the console: ***************************************** ************ EARLY BOOT VFP ************* End of early boot detected ***************************************** Firmware Version 41.36 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State CoProcessor State Cache Size Number State Inst Data --------- -------- --------------------- ----------------- ------------ 0 650 MHz Active Functional 750 KB 1.5 MB Central Bus Speed (in MHz) : 133 Available Memory : 1048576 KB Good Memory Required : 25000 KB Primary boot path: 0/0/2/1.2 Alternate boot path: 0/0/2/1.2 Console path: 0/0/4/1.0 Keyboard path: 0/0/4/0.0 Processor is booting from first available device. To discontinue, press any key within 10 seconds. 10 seconds expired. Proceeding... Trying Primary Boot Path ------------------------ Booting... Boot IO Dependent Code (IODC) revision 1 HARD Booted. palo ipl 1.2 root@b2000 Tue Jan 14 13:13:07 MST 2003 Boot image contains: 0/vmlinux32 3687647 bytes @ 0x639800 0/vmlinux64 4719374 bytes @ 0x9be000 0/ramdisk 2663046 bytes @ 0xe3e800 Information: No console specified on kernel command line. This is normal. PALO will choose the console currently used by firmware (serial). Command line for kernel: 'ramdisk_size=8192 root=/dev/ram console=ttyS0 TERM=vt1 02 palo_kernel=0/vmlinux' Selected kernel: /vmlinux from partition 0 Selected ramdisk: /ramdisk from partition 0 Warning: kernel name doesn't end with 32 or 64 -- Guessing... Choosing 64-bit ke rnelELF64 executable Entry 00100000 first 00100000 n 4 Segment 0 load 00100000 size 2568152 mediaptr 0x1000 Segment 1 load 00374000 size 722104 mediaptr 0x274000 Segment 2 load 00428000 size 463872 mediaptr 0x325000 Segment 3 load 0049c000 size 49152 mediaptr 0x397000 Loading ramdisk 2663046 bytes @ 3fd65000... Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org Linux version 2.4.17-64 (root@paer) (gcc version 3.0) #1 Sat Mar 16 17:31:44 MST 2002 FP[0] enabled: Rev 1 Model 19 The 64-bit Kernel has started... Determining PDC firmware type: 64 bit PAT. model 00005e00 00000491 00000000 00000002 2ef72083 100000f1 00000008 000000b2 00 0000b2 vers 00000203 CPUID vers 19 rev 8 (0x00000268) model 9000/800/L1500-6x Total Memory: 1024 Mb initrd: 4fd65000-4ffef286 initrd: reserving 3fd65000-3ffef286 (mem_max 40000000) pagetable_init On node 0 totalpages: 262144 zone(0): 262144 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: ramdisk_size=8192 root=/dev/ram console=ttyS0 TERM=vt102 pa lo_kernel=0/vmlinux Console: colour dummy device 160x64 Calibrating delay loop... 1297.61 BogoMIPS Memory: 1009096k available Dentry-cache hash table entries: 131072 (order: 9, 2097152 bytes) Inode-cache hash table entries: 65536 (order: 8, 1048576 bytes) Mount-cache hash table entries: 16384 (order: 6, 262144 bytes) Buffer-cache hash table entries: 65536 (order: 7, 524288 bytes) Page-cache hash table entries: 262144 (order: 9, 2097152 bytes) Searching for devices... Found devices: 1. Memory (1) at 0xfffffffffedc0000 [192], versions 0x90, 0x0, 0x9 2. IKE I/O Bus Converter Merced Port (7) at 0xfffffffffed00000 [0], versions 0x8 03, 0x0, 0xc 3. Elroy PCI Bridge (13) at 0xffffffff9ffe0000 [0/0], versions 0x782, 0x0, 0xa 4. Elroy PCI Bridge (13) at 0xffffffff9ffe2000 [0/1], versions 0x782, 0x0, 0xa 5. Elroy PCI Bridge (13) at 0xffffffff9ffe4000 [0/2], versions 0x782, 0x0, 0xa 6. Elroy PCI Bridge (13) at 0xffffffff9ffe6000 [0/3], versions 0x782, 0x0, 0xa 7. Elroy PCI Bridge (13) at 0xffffffff9ffe8000 [0/4], versions 0x782, 0x0, 0xa 8. Elroy PCI Bridge (13) at 0xffffffff9ffea000 [0/5], versions 0x782, 0x0, 0xa 9. Elroy PCI Bridge (13) at 0xffffffff9fff0000 [0/8], versions 0x782, 0x0, 0xa 10. Elroy PCI Bridge (13) at 0xffffffff9fff2000 [0/9], versions 0x782, 0x0, 0xa 11. Elroy PCI Bridge (13) at 0xffffffff9fff4000 [0/10], versions 0x782, 0x0, 0xa 12. Elroy PCI Bridge (13) at 0xffffffff9fff8000 [0/12], versions 0x782, 0x0, 0xa 13. DEW BC Runway Port (7) at 0xfffffffffed20000 [32], versions 0x584, 0x0, 0xc 14. Unknown machine (0) at 0xfffffffffed21000 [33], versions 0x5e0, 0x0, 0x0 CPU(s): 1 x PA8600 (PCX-W+) at 650.000000 MHz SBA found Ike rev 2 at 0xfffffffffed00000 lba version TR4.0 (0x5) found at 0xffffffff9ffe0000 lba range[2] : ignoring GMMIO (0xfffffff004000000) lba version TR4.0 (0x5) found at 0xffffffff9ffe2000 kernel BUG at lba_pci.c:1250! kernel BUG at lba_pci.c:1285! lba range[2] : ignoring GMMIO (0xfffffff084000000) lba version TR4.0 (0x5) found at 0xffffffff9ffe4000 kernel BUG at lba_pci.c:1250! kernel BUG at lba_pci.c:1285! lba range[2] : ignoring GMMIO (0xfffffff104000000) lba version TR4.0 (0x5) found at 0xffffffff9ffe6000 kernel BUG at lba_pci.c:1250! kernel BUG at lba_pci.c:1285! lba range[2] : ignoring GMMIO (0xfffffff184000000) lba version TR4.0 (0x5) found at 0xffffffff9ffe8000 lba range[2] : ignoring GMMIO (0xfffffff204000000) lba version TR4.0 (0x5) found at 0xffffffff9ffea000 kernel BUG at lba_pci.c:1250! kernel BUG at lba_pci.c:1285! lba range[2] : ignoring GMMIO (0xfffffff284000000) lba version TR4.0 (0x5) found at 0xffffffff9fff0000 kernel BUG at lba_pci.c:1250! kernel BUG at lba_pci.c:1285! lba range[2] : ignoring GMMIO (0xfffffff404000000) lba version TR4.0 (0x5) found at 0xffffffff9fff2000 kernel BUG at lba_pci.c:1250! kernel BUG at lba_pci.c:1285! lba range[2] : ignoring GMMIO (0xfffffff484000000) lba version TR4.0 (0x5) found at 0xffffffff9fff4000 lba range[2] : ignoring GMMIO (0xfffffff504000000) lba version TR4.0 (0x5) found at 0xffffffff9fff8000 lba range[2] : ignoring GMMIO (0xfffffff604000000) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Performance monitoring counters enabled for Unknown machine Starting kswapd Journalled Block Device driver loaded pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en abled Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (103c,1048,103c,104b) and the manufacturer and name of serial board or modem board to serial-pci-info@lists.sourceforge.net. ttyS00 at iomem 0xffffffff80000000 (irq = 132) is a 16550A ttyS01 at iomem 0xffffffff80000008 (irq = 132) is a 16550A ttyS02 at iomem 0xffffffff80000010 (irq = 132) is a 16550A ttyS03 at iomem 0xffffffff80000030 (irq = 132) is a 16550A ttyS04 at iomem 0xffffffff80000038 (irq = 132) is a 16550A request_module[parport_lowlevel]: Root fs not mounted lp: driver loaded but no devices found Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com) block: 128 slots per queue, batch=32 RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx loop: loaded (max 8 devices) Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1000 status 7809 advertising 0061. eth0: Digital DS21143 Tulip rev 65 at 0x80, 00:30:6E:13:C6:42, IRQ 128. SCSI subsystem driver Revision: 1.00 sym53c8xx: at PCI bus 0, device 2, function 0 sym53c8xx: 53c875 detected sym53c8xx: at PCI bus 0, device 2, function 1 sym53c8xx: 53c875 detected sym53c8xx: at PCI bus 80, device 0, function 0 sym53c8xx: 53c895 detected sym53c8xx: at PCI bus 96, device 0, function 0 sym53c8xx: 53c895 detected sym53c8xx: at PCI bus 0, device 1, function 0 sym53c8xx: setting PCI_COMMAND_INVALIDATE (fix-up) sym53c8xx: 53c896 detected sym53c8xx: at PCI bus 0, device 1, function 1 sym53c8xx: setting PCI_COMMAND_INVALIDATE (fix-up) sym53c8xx: 53c896 detected sym53c875-0: rev 0x37 on pci bus 0 device 2 function 0 irq 130 sym53c875-0: ID 7, Fast-20, Parity Checking ************* SYSTEM ALERT ************** SYSTEM NAME: fileserver-c DATE: 05/18/2004 TIME: 15:35:24 ALERT LEVEL: 7 = reserved REASON FOR ALERT SOURCE: 0 = unknown, no source stated SOURCE DETAIL: 0 = unknown, no source stated SOURCE ID: FF PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH FLASH FLASH ON ON LED State: Unexpected Reboot. Running non-OS code. Non-critical error detected. Check Chassis and Console Logs for error messages. 0x0000007000FF6292 000000FF FF800000 - type 0 = Data Field Unused 0x5800087000FF6292 00006804 120F2318 - type 11 = Timestamp 05/18/2004 15:35:24 A: ack read of this entry - X: Disable all future alert messages Anything else skip redisplay the log entry ->Choice:Timeout! ***************************************** The system then gets stuck (Hangs) if I try pressing a i get the same, pressing x has the effect of adding this to the end of the above : CAUTION: System Alerts have been disabled. This will re-enable with a re-boot or power-on of the system. To re-enable system alerts now, you may use the AC (Alert Display Configuration) command. ************* SYSTEM ALERT ************** Alert messages are now disabled. Enter Commands Interface AC command to enable t hem again ***************************************** Any ideas? James On May 18, 2004 08:07 AM, Joel Soete <jsoe0708@tiscali.be> wrote: > > -- Original Message -- > > From: "James Morris" <jmorris@photonicmaterials.com> > > To: "'Joel Soete'" <jsoe0708@tiscali.be> > > Date: Mon, 17 May 2004 13:52:38 +0100 > > Subject: Problem installing on HP RP5400 > > > > > > I am trying to install on a HP RP5400 and cannot get the disc image to > boot > > (from CD-rom) anybody else done tried installing on the RP5400? > > James > > > > Hello James, > > I just test one run of 2.4 smp 64bits on a brother system a L2000 (your > is aka L1000 according http://www.openpa.net/systems/rhapsody.html), so > linux would run on system ;). > > But may I suugest you to check first the nice FAQ: > http://www.parisc-linux.org/faq/index.html > > which describe you in detail how to get, to burn and eventually check your > boot CD (may I recommended you to use one of the latest sarge netinstall > available > http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/hppa/current/sarge-hppa-netinst.iso; > have a look to Stex success <http://lists.debian.org/debian-hppa/2004/05/msg00067.html> > and other ;) > > If never you still encounter much pb, it would be nice that you also have > a look on <http://www.parisc-linux.org/faq/kernelbug-howto.html> to report > much accurately your pb ; > > Thanks, > Joel > > > ---------------------------------------------------------------------------------------- > Tiscali ADSL, 27,50 €/mois...pendant 6 mois. > La meilleure offre du marché ! > http://reg.tiscali.be/default.asp?lg=fr > > >
--- End Message ---