Problem with graphics-card

To: debian-hppa@lists.debian.org
Subject: Problem with graphics-card
From: "Henry Schimmer" <Henry_Schimmer@gmx.de>
Date: Thu, 30 Oct 2003 12:25:47 +0100 (MET)
Message-id: <[🔎] 29871.1067513147@www6.gmx.net>
Hi,

I'm facing a problem running my GSC-based graphics-adapter in my C360. It
seems to  me that the driver fails to initialize the card :

Linux version 2.4.20-32 (root@j5k) (gcc version 3.0.4) #1 Thu Apr 17
15:10:17 MDT 2003
FP[0] enabled: Rev 1 Model 16
The 32-bit Kernel has started...
...
CPUID vers 14 rev 0 (0x000001c0)
capabilities 0x2
model 9000/785/C360								<====
Total Memory: 1024 Mb
...
Kernel command line: root=/dev/sdb3 HOME=/ console=tty0 sti=8/4
sti_font=VGA8x16 TERM=linux palo_kernel=3/boot/vmlinux
Console: colour dummy device 160x64
...
Found devices:
1. U2-IOA BC Runway Port (12) at 0xfff88000 [8], versions 0x580, 0xf, 0xb
2. Dino PCI Bridge (13) at 0xf2000000 [8/0], versions 0x680, 0x3, 0xa, 
additional addresses: 0xf2800000 
3. Raven U/L2 Dino RS-232 (10) at 0xf2003000 [8/0/63], versions 0x6, 0x0,
0x8c
4. Raven U/L2 Dino PS/2 Port (10) at 0xf2001000 [8/1], versions 0x6, 0x0,
0x96
5. Coral SGC Graphics (10) at 0xfa000000 [8/4], versions 0x4, 0x0, 0x77
6. Raven+ w SE FWSCSI Core BA (11) at 0xffd00000 [8/16], versions 0x56, 0x0,
0x81,  additional addresses: 0xffd0c000 0xffc00000 
7. Raven+ w SE FWSCSI Core Centronics (10) at 0xffd02000 [8/16/0], versions
0x56, 0x0, 0x74,  additional addresses: 0xffd01000 0xffd03000 
8. Raven+ w SE FWSCSI Core Audio (10) at 0xffd04000 [8/16/1], versions 0x56,
0x4, 0x7b
9. Raven+ w SE FWSCSI Core RS-232 (10) at 0xffd05000 [8/16/4], versions
0x56, 0x0, 0x8c
10. Raven+ w SE FWSCSI Core SCSI (10) at 0xffd06000 [8/16/5], versions 0x56,
0x0, 0x82
11. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08000 [8/16/7], versions
0x56, 0x0, 0x84
12. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08100 [8/16/8], versions
0x56, 0x0, 0x84
13. U2-IOA BC GSC+ Port (7) at 0xf203f000 [8/63], versions 0x501, 0x1, 0xc
14. U2-IOA BC Runway Port (12) at 0xfff8a000 [10], versions 0x580, 0xf, 0xb
15. Cujo PCI Bridge (13) at 0xf1000000 [10/0], versions 0x682, 0x1, 0xa, 
additional addresses: 0xf1800000 0xf6000000 
16. Dino RS-232 (10) at 0xf1003000 [10/3], versions 0x7, 0x0, 0x8c
17. U2-IOA BC GSC+ Port (7) at 0xf103f000 [10/63], versions 0x501, 0x1, 0xc
18. Raven W 360 (9000/780) (0) at 0xfffa0000 [32], versions 0x5c6, 0x0, 0x4
19. Memory (1) at 0xfffb1000 [49], versions 0x97, 0x0, 0x9
CPU(s): 1 x PA8500 (PCX-W) at 367.111100 MHz
Found U2 at 0xfff88000
Found U2 at 0xfff8a000
Lasi version 0 at 0xffd00000 found.
Dino version 3.1 found at 0xf2000000
Cujo version 2.0 found at 0xf1000000
Enabling Cujo 2.0 bug workaround
Don't recognise Cujo at address 0xf1000000, not enabling workaround		<---- ?
...
STI GSC/PCI graphics driver version 0.9
STI byte mode ROM at fa000000, hpa at fa000000
STI id 2bcb015a-9a02587, conforms to spec rev. 8.04				<---- Coral SCG
STI init_graph failed (ret -1, errno 258)					<==== arrrrgh !
STI PCI graphic ROM found at f1e00000 (2048 kB), fb at f6000000 (32 MB)
STI word mode ROM at f1e00044, hpa at f6000000
STI id 2fc1066b-9a02587, conforms to spec rev. 8.09				<---- FX-6
STI device: HPA4554A
stifb: Unsupported gfx card id 0x2fc1066b					<---- known problem :(((
...
sticon: Initializing STI text console.
Console: switching to colour STI console 160x64
...
HP SDC: No SDC found.
HP SDC MLC: Registering the System Domain Controller's HIL MLC.			<---- ?
HP SDC MLC: Request for raw HIL ISR hook denied
...
do_page_fault() pid=288 command='modprobe' type=15 address=0xfb700000		oh, I
haven't seen that ...
vm_start = 0xfaf00000, vm_end = 0xfb700000

     YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001111111000001111 Not tainted
r00-03  00000000 4017fb3c 401077ab 4017e33c
r04-07  4017e33c 00001000 401802a0 00cf6fe8
r08-11  00000000 00000fff 00000002 00000020
r12-15  4017e33c 00000000 fffff000 00000000
r16-19  00000000 0002f800 000447f0 4017e33c
r20-23  00000001 40178b20 4017fb3c 401802b0
r24-27  00000018 401802a0 00000000 000437f0
r28-31  00cf6fe8 00000010 fb700000 400a959f
sr0-3   0000027e 0000027e 00000000 0000027e
sr4-7   0000027e 0000027e 0000027e 0000027e

IASQ: 0000027e 0000027e IAOQ: 401076d3 401076d7
 IIR: 6fc60080    ISR: 0000027e  IOR: fb700000
 CPU:        0   CR30: 4eadc000 CR31: 103d8000
 ORIG_R28: 000491ec


I'm sure the Coral is a) working
		      b) supported by woody | 
					    |
					    v

BOOT_ADMIN> info

System model number: HP 9000/715/64
Processor revision 2.3   64MHz
...
BootRom Version    1.4  


BOOT_ADMIN> boot
...
palo ipl 1.0 root@palinux Mon Apr  1 10:02:53 MST 2002
...
PALO(F0) partition contains:
    0/vmlinux32 3687647 bytes @ 0x48000
...
Command line for kernel: 'root=/dev/sda4 HOME=/ console=ttyS0 TERM=vt102
palo_kernel=4/boot/vmlinux'
...
Linux version 2.4.19-pa21 (bame@dsl2) (gcc version 3.0.3) #1 Thu Oct 3
17:11:44 MDT 2002

FP[0] enabled: Rev 1 Model 13

The 32-bit Kernel has started...
Determining PDC firmware type: Snake.
...
Found devices:
1. Coral SGC Graphics (10) at 0xf4000000 [0], versions 0x4, 0x0,
0x77			<========
2. Mirage Jr GSC Builtin Graphics (10) at 0xf8000000 [1], versions 0x12,
0x0, 0x85
...
CPU(s): 1 x PA7100LC (PCX-L) at 64.000000 MHz
Lasi version 0 at 0xf0100000 found.
LED display at f00e0000 registered
Wax at 0xf0200000 found.
...
STI GSC/PCI graphics driver version 0.9
STI byte mode ROM at f4000000, hpa at f4000000
STI id 2bcb015a-9a02587, conforms to spec rev. 8.04					<---- Coral SCG
STI device: HPA4071A_Z

STI word mode ROM at f0025000, hpa at f8000000
STI id 2b4ded6d-40a00499, conforms to spec rev. 8.04					<---- MirageJr
internal gfx
STI device: HPA208LC1024
Console: switching to colour frame buffer device 160x64
fb0: stifb 1280x1024-32 frame buffer device, id: 2bcb015a, mmio:
0xf4100000		<---- Coral SCG
fb1: stifb 1024x768-8 frame buffer device, id: 2b4ded6d, mmio:
0xf8100000		<---- MirageJr internal gfx
...


In the bootadmin-menu of both machines I selected the Coral as console-path.
Beautyful with my 715-64 (GSC-only; the bootprocess
in my C360 (PCI + GSC) chooses to switch to the FX-6 in text-mode after the
well-known message "... you may need to switch console".

Has anyone an idea of which kind the problem may be ? My guess is the U2-IOA
BC GSC(+) Port.

friendly


    Henry Schimmer

-- 
NEU FÜR ALLE - GMX MediaCenter - für Fotos, Musik, Dateien...
Fotoalbum, File Sharing, MMS, Multimedia-Gruß, GMX FotoService

Jetzt kostenlos anmelden unter http://www.gmx.net

+++ GMX - die erste Adresse für Mail, Message, More! +++
Reply to:
Follow-Ups:
- Re: Problem with graphics-card
  - From: Matthew Wilcox <willy@debian.org>
Prev by Date: Re: Firmware question - B132L
Next by Date: Re: Problem with graphics-card
Previous by thread: Re: Firmware question - B132L
Next by thread: Re: Problem with graphics-card
Index(es):
- Date
- Thread