aprsd config problem?
Hello all,
I wrote regarding this awhile back, but my install was too cobbled to
tshoot. I've since re-installed Woody, compiled a custom kernel with AX.25
protocol support, reinstalled the libax25, ax25-tools, ax25-apps and
reinstalled aprsd.
I still suffer the same problem I had with the previous install, i.e., aprsd
won't stream output to it's ports (as config'd in aprsd.conf).
-If I telnet (from localhost or remote) to the non-history and raw ports, I
get only my server's beacon returned once only.
-If I telnet (from localhost or remote) to ports w/history, I get the
history dump as of the time of socket connect, but no further data streams
out.
-My aprs client sw, UI-View32, is config'd to mainport (10151). When it
connects, it gets the history dump, but no further data until its' timout,
and then it reconnects (same behavior whether the client officially "logs
in" or not). This reconnect results in another "aprsd -d" process being
spawned (as indicated by ps -aux). The STAT of all "aprsd -d" processes
remain "S" (Sleeping). The number of aprsd processes will increase into the
hundreds as re\connections occur).
-All the while, "listen" displays a constant incoming stream of aprs data
from the port.
Hardware config:
Via Eden 5000
10\100 NIC
TNC X(kiss only)->/dev/ttyS0
Relevent config data is as follows:
axports:
aprs2m KG4OFO-13 9600 255 2 144.390 MHz (APRS 1200bps on
air)
ax25.init (per www.febo.com):
/usr/sbin/kissattach /dev/ttyS0 aprs2m 44.71.36.65
/usr/sbin/kissparms -p aprs2m -f no -l 50 -r 32 -s 320 -t 320
/sbin/ifconfig ax0 broadcast 44.71.36.127 netmask 255.255.255.192
/sbin/ifconfig ax0 arp mtu 256 up
/sbin/route add -net 44.71.36.64 irtt 4000 ax0
/etc/ax25# ifconfig
ax0 Link encap:AMPR AX.25 HWaddr KG4OFO-13
inet addr:44.71.36.65 Bcast:44.71.36.127 Mask:255.255.255.192
UP BROADCAST RUNNING MTU:256 Metric:1
RX packets:558 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
RX bytes:41439 (40.4 KiB) TX bytes:254 (254.0 b)
eth0 Link encap:Ethernet HWaddr 00:40:63:CC:0A:CE
inet addr:192.168.1.5 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1141 errors:0 dropped:0 overruns:0 frame:0
TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:115839 (113.1 KiB) TX bytes:136042 (132.8 KiB)
Interrupt:11 Base address:0xe800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
/etc/ax25# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
44.71.36.64 * 255.255.255.192 U 0 0 0 ax0
192.168.1.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
Anyone understand what the problem and solution is to this? It's driving me
crazy.
Thanks,
Rick - kg4ofo
Reply to: