Lecteur cartes Flash PNY ?
J'ai un pb avec la reconnaissance de ce lecteur sous Woody avec noyau 2.4.2
J'ai un module "usb-storage" a priori correct, patché avec "datafab_lexar_241ac2.diff"
J'ai installé "scsi_mod".
Le PB, c'est que je n'arrive pas a affecter /dev/sda1 au lecteur!
Ci joint le CR de dmesg. Si quelqu'un a déjà résolu ce problème, je lui en serais éternellement reconnaissant !
Christophe
Linux version 2.4.2 (root@debian) (gcc version 2.95.3 20010219 (prerelease)) #6 Sat Apr 14 19:56:13 CEST 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 0000000007efd000 @ 0000000000100000 (usable)
BIOS-e820: 0000000000002000 @ 0000000007ffd800 (ACPI data)
BIOS-e820: 0000000000000800 @ 0000000007ffd000 (ACPI NVS)
On node 0 totalpages: 32765
zone(0): 4096 pages.
zone(1): 28669 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux3 ro root=344
Initializing CPU#0
Detected 400.915 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.53 BogoMIPS
Memory: 126568k/131060k available (1091k kernel code, 4104k reserved, 435k data, 180k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.37 (20001109) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb130, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
parport0: PC-style at 0x378 [PCSPP(,...)]
parport0: irq 7 detected
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
block: queued sectors max/low 84053kB/28017kB, 256 slots per queue
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 91152D8, ATA DISK drive
hdb: Maxtor 53073U6, ATA DISK drive
hdc: SAMSUNG CD-ROM SCR-3232 VH102, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 22510656 sectors (11525 MB) w/256KiB Cache, CHS=1401/255/63, UDMA(33)
hdb: 60030432 sectors (30736 MB) w/2048KiB Cache, CHS=3736/255/63
hdc: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
hdb: hdb1 hdb2 hdb3 hdb4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Creative EMU10K1 PCI Audio Driver, version 0.7, 20:08:32 Apr 13 2001
PCI: Found IRQ 15 for device 00:14.0
IRQ routing conflict in pirq table for device 00:14.0
emu10k1: EMU10K1 rev 7 model 0x8040 found, IO at 0xe800-0xe81f, IRQ 11
Linux PCMCIA Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 13:02:18 Apr 14 2001
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF c126b2c0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: e000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c126b2c0
usb.c: call_policy add, num 1 -- no FS yet
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
hub.c: port 1 connection change
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 103, change 0, 12 Mb/s
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: kmalloc IF c126b420, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
ds: no socket drivers loaded!
usb.c: USB device number 2 default language ID 0x409
Manufacturer: DataFab Systems Inc.
Product: USB CF
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x7c4/0xa000) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 1.00
Vendor:Product = 07c4:a000
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 0.12
Device Class:SubClass:Protocol = ff:00:00
Vendor class
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0020
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 100mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 02
bInterface Class:SubClass:Protocol = 05:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 01 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 82 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
usb.c: call_policy add, num 2 -- no FS yet
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 180k freed
Adding Swap: 136544k swap-space (priority -1)
via-rhine.c:v1.08b-LK1.1.6 8/9/2000 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
PCI: Assigned IRQ 9 for device 00:12.0
eth0: VIA VT3043 Rhine at 0xe400, 00:50:ba:09:5e:8e, IRQ 9.
eth0: MII PHY found at address 8, status 0x782d advertising 05e1 Link 0000.
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.57 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge needs ETBF enabled.
bttv: Bt8xx card found (0).
PCI: Assigned IRQ 5 for device 00:10.0
bttv0: Bt848 (rev 18) at 00:10.0, irq: 5, latency: 64, memory: 0xed000000
bttv0: model: BT848A(MIRO PCTV) [insmod option]
bttv0: enabling 430FX/VP3 compatibilty
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: miro: id=9 tuner=3 radio=no stereo=no
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951)
i2c-core.o: driver generic i2c audio driver registered.
i2c-core.o: driver i2c TV tuner driver registered.
tuner: chip found @ 0x60
bttv0: i2c attach [Philips SECAM]
i2c-core.o: client [Philips SECAM] registered to adapter [bt848 #0](pos. 0).
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Reply to: