etch pr2 - trouble with Adaptec 2100S RAID-controller
I'm testing etch pr2, and I have experienced some problems after
the first boot. I get a message about bad superblock, and the
proposed e2fsck -b 8193 only repeatet the message about bad
superblock.
When I use a LiveCD to format the disks, and then install etch,
I'm not getting the superblock message. And I'm able to set up
a network of thin clients with sound.
apt-get update && upgrade before running ltsp-make-client installs
new kernel form security. (2.6.18-4-something)
The required reboot results in a new superblock message.
From dmesg I can read:
Adapter 00000012: TID 0000:[HPC*]:PCI 1: Bus 1 Device 22 Function 0
i2o: iop0: Controller added
SCSI subsystem initialized
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
PCI: Unable to reserve mem region #1:2000000@fc000000 for device
0000:02:09.1
dpti: adpt_config_hba: pci request region failed
Could not Init an I2O RAID device
Will not try to detect others.
The last part of lspci listing looks like this:
02:09.0 PCI bridge [0604]: Adaptec (formerly DPT) PCI Bridge [1044:a500]
(rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: 00100000-000fffff
Prefetchable memory behind bridge: 00100000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:09.1 I2O [0e00]: Adaptec (formerly DPT) SmartRAID V Controller
[1044:a501] (rev 02) (prog-if 01)
Subsystem: Adaptec (formerly DPT) 2000S Ultra3 Single Channel
[1044:c03c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 185
BIST result: 00
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=32M]
[virtual] Expansion ROM at f8060000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Reply to: