Startx fails after updating my slink system!!!
Hello,
yesterday I updated my slink system to the current state. It was
on the state of 20th December and was running stable.
The X packages were untouched over this time!!
After the update (no packages form the x11 section needed an update)
startx fails :-((.
Here is the output:
XFree86 Version 3.3.2.3 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: July 15 1998
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.1.105 i586 [ELF]
Configured drivers:
Mach64: accelerated server for ATI Mach64 graphics adaptors (Patchlevel 0)
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc102"
(**) XKB: layout: "de"
(**) XKB: variant: "nodeadkeys"
(**) Mouse: type: Microsoft, device: /dev/mouse, baudrate: 1200
(**) Mouse: buttons: 3, 3 button emulation (timeout: 50ms)
(**) Mach64: Graphics device ID: "Primary Card"
(**) Mach64: Monitor ID: "Meiner"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/75dpi:unscaled,/usr/X11R6/lib/X11/fonts/75dpi,/usr/X11R6/lib/X11/fonts/sharefont/,/usr/X11R6/lib/X11/fonts/freefont/"
(--) Mach64: PCI: Mach64 VT rev 64, Aperture @ 0xe0000000, Block I/O @ 0x6200
(--) Mach64: Card type: PCI
(--) Mach64: Memory type: 3
(--) Mach64: Clock type: Internal
(--) Mach64: Maximum allowed dot-clock: 80.000 MHz
(**) Mach64: Mode "1024x768": mode clock = 75.000
(**) Mach64: Mode "800x600": mode clock = 50.000
(**) Mach64: Mode "640x480": mode clock = 45.800
(**) Mach64: Virtual resolution: 1160x870
(--) Mach64: Video RAM: 2048k
(--) Mach64: Using hardware cursor
(--) Mach64: Using 16 MB aperture @ 0xe0000000
(--) Mach64: Ramdac is Internal
(--) Mach64: Ramdac speed: 80 MHz
(**) Mach64: Color weight: 565
(--) Mach64: Pixmap cache: 0 256x256 slots, 0 128x128 slots, 0 64x64 slots
(--) Mach64: Font cache: 0 fonts
Fatal server error:
could not open default font 'fixed'
When reporting a problem related to a server crash, please send
the full server output, not just the last messages
_X11TransSocketUNIXConnect: Can't connect: errno = 111
giving up.
xinit: Verbindungsaufbau abgelehnt (errno 111): unable to connect to X server
xinit: Kein passender Prozeß gefunden (errno 3): Server error.
I havn't the faintest idea what to do.
Please send me any helpfull suggestions where to check or what to do.
I'm in serios trouble.
Kind regards
Andreas.
Reply to: