Bug#1027758: On Tyan TN71-BP012 (POWER8) Debian 11.6 successfully installed
Package: installation-reports
Boot method: USB stick
Date: 2022 Fri Dec 30 15:01
Machine: Tyan TN71-BP012
Processor: ppc64el POWER8 (raw), altivec supported
Memory: 133598MB
Partitions:
Sys. de fichiers Type blocs de 1K Utilisé Disponible Uti% Monté sur
udev devtmpfs 63386560 0 63386560 0% /dev
tmpfs tmpfs 13359936 15168 13344768 1% /run
/dev/sda2 ext4 238263032 3925436 222161676 2% /
tmpfs tmpfs 66799424 0 66799424 0% /dev/shm
tmpfs tmpfs 5120 0 5120 0% /run/lock
tmpfs tmpfs 13359872 832 13359040 1% /run/user/1000
Output of lspci -knn (or lspci -nn):
0000:00:00.0 PCI bridge [0604]: IBM POWER8 Host Bridge (PHB3) [1014:03dc]
0001:00:00.0 PCI bridge [0604]: IBM POWER8 Host Bridge (PHB3) [1014:03dc]
0001:01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:08.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:09.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:0a.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:10.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:02:11.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8748 48-Lane, 12-Port PCI Express Gen 3 (8 GT/s) Switch, 27 x 27mm FCBGA [10b5:8748] (rev ca)
0001:03:00.0 Ethernet controller [0200]: Mellanox Technologies MT27520 Family [ConnectX-3 Pro] [15b3:1007]
Subsystem: Mellanox Technologies MT27520 Family [ConnectX-3 Pro] [15b3:0050]
Kernel driver in use: mlx4_core
Kernel modules: mlx4_core
0001:04:00.0 Ethernet controller [0200]: Mellanox Technologies MT27520 Family [ConnectX-3 Pro] [15b3:1007]
Subsystem: Mellanox Technologies MT27520 Family [ConnectX-3 Pro] [15b3:0050]
Kernel driver in use: mlx4_core
Kernel modules: mlx4_core
0001:05:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9235 PCIe 2.0 x2 4-port SATA 6 Gb/s Controller [1b4b:9235] (rev 11)
Subsystem: Marvell Technology Group Ltd. 88SE9235 PCIe 2.0 x2 4-port SATA 6 Gb/s Controller [1b4b:9235]
Kernel driver in use: ahci
Kernel modules: ahci
0001:06:00.0 USB controller [0c03]: Texas Instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller [104c:8241] (rev 02)
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
0001:07:00.0 PCI bridge [0604]: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge [1a03:1150] (rev 03)
0001:08:00.0 VGA compatible controller [0300]: ASPEED Technology, Inc. ASPEED Graphics Family [1a03:2000] (rev 30)
Subsystem: ASPEED Technology, Inc. ASPEED Graphics Family [1a03:2000]
Kernel driver in use: ast
Kernel modules: ast
0002:00:00.0 PCI bridge [0604]: IBM POWER8 Host Bridge (PHB3) [1014:03dc]
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O] *firmware non free needed.(firmware-misc-nonfree_20210315-3_all.deb) mlx4_core
Detect media: [O] *no grub menu for boot media (USB stick) have to create menu entry in Petitboot
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O] *grub menu on disk display in Petitboot working fine
Overall install: [O]
Comments/Problems:
To boot USB stick "manual" Petitboot entry have to be created with:
selecting USB stick device (here sdb)
Kernel: /install/vmlinux
Initrd: /install/initrd.gz
Boot arguments: /root=/dev/sdb ro quiet
After intallation grub boot menu working fine on computer SSD (here sda)
Installed system working fine Thanks.
Best regards
Reply to: