I tried to instal Debian 11 on my BananaPI R1 (Lamobo R1) because I needed a newer kernel version for my application with the BPI.
System Ready SD-Card Images around only have older Kernels.
Package: installation-reports
Boot method: <I tried to Install the System by using an SD-Card Image explained here https://wiki.debian.org/InstallingDebianOn/Allwinner with the Files ... https://deb.debian.org/debian/dists/stable/main/installer-armhf/current/images/netboot/SD-card-images/firmware.Lamobo_R1.img.gz & https://deb.debian.org/debian/dists/stable/main/installer-armhf/current/images/netboot/SD-card-images/partition.img.gz >
Date: <22.11.2021>
Machine: <BananaPi R1 - Lamobo R1>
Processor: Allwinner A20
Memory: 1Gig
Partitions:
~ # df -T
Filesystem Type 1K-blocks Used Available Use% Mounted on
tmpfs tmpfs 102072 12 102060 0% /run
devtmpfs devtmpfs 449132 0 449132 0% /dev
Output of lspci -knn (or lspci -nn):
Is not working in the Installer Shell
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [E]
Configure network: [E]
Detect media: [ ]
Load installer modules: [ ]
Detect hard drives: [ ]
Partition hard drives: [ ]
Install base system: [ ]
Clock/timezone setup: [ ]
User/password setup: [ ]
Install tasks: [ ]
Install boot loader: [ ]
Overall install: [ ]
Comments/Problems:
Under U-boot the Keybord was detected.
When the Linux installer is ready, the Keyboard isn't working any more.
I bought a Serial UART Debug device and now I am able to go through the Linux Installer via Serial Console. Unfortunately I was only able to select English for the Language.
But later on the Network Interface seems not to work.
I know the Network Controler of the Lamobo R1 is not an easy one. I am still a Linux padawan and lightyears away from a Jedi status, but I hope you can give me some advice to get the System up running.
with kind regards from Germany - Sascha Martens
Here is the Information Screen in Linux Installer with the Network detection
[ (1*installer) 2 shell 3 shell 4- log ][ Jan 01 0:26 ]
lqqqqqqqqqqqqqqqqqqqqu [!!] Configure the network tqqqqqqqqqqqqqqqqqqqqqk
x x
x Network autoconfiguration failed x
x Your network is probably not using the DHCP protocol. Alternatively, x
x the DHCP server may be slow or some network hardware is not working x
x properly. x
x x
x <Continue> x
x x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
<Tab> moves; <Space> selects; <Enter> activates buttons
Here is the Information which is transferred over the Serial Debug Console.
U-Boot SPL 2021.01+dfsg-5 (May 23 2021 - 04:32:45 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2021.01+dfsg-5 (May 23 2021 - 04:32:45 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Lamobo R1
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment
HDMI connected: EDID: invalid EDID data
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@1c50000
starting USB...
Bus usb@1c14000: USB EHCI 1.00
Bus usb@1c14400: USB OHCI 1.0
Bus usb@1c1c000: USB EHCI 1.00
scanning bus usb@1c14000 for devices... 1 USB Device(s) found
scanning bus usb@1c14400 for devices... 1 USB Device(s) found
scanning bus usb@1c1c000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 2 ms (768.6 KiB/s)
## Executing script at 43100000
Mainline u-boot / new-style environment detected.
4956672 bytes read in 278 ms (17 MiB/s)
26960 bytes read in 12 ms (2.1 MiB/s)
22629196 bytes read in 1265 ms (17.1 MiB/s)
Booting the Debian installer...
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
EHCI failed to shut down host controller.
Loading Ramdisk to 48a6b000, end 49fffb4c ... OK
Loading Device Tree to 48a61000, end 48a6a94f ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.0-9-armmp (debian-kernel@lists.debian.org) (gc c-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.70-1 (2021-09-30)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache
[ 0.000000] OF: fdt: Machine model: Lamobo R1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x4a000000, size 96 M iB
[ 0.000000] OF: reserved mem: initialized node default-pool, compatible id sh ared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] percpu: Embedded 21 pages/cpu s54604 r8192 d23220 u86016
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, li near)
[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000] Memory: 898268K/1048576K available (11264K kernel code, 1667K rwd ata, 3188K rodata, 2048K init, 333K bss, 52004K reserved, 98304K cma-reserved, 2 62144K highmem)
[ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x30/0x42c with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 37383 entries in 110 pages
[ 0.000000] ftrace: allocated 110 pages with 5 groups
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jif fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns
[ 0.000026] Switching to timer-based delay loop, resolution 41ns
[ 0.001733] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ idle_ns: 79635851949 ns
[ 0.003027] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 6370868154 ns
[ 0.003930] Console: colour dummy device 80x30
[ 0.004022] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=96000)
[ 0.004047] pid_max: default: 32768 minimum: 301
[ 0.004347] LSM: Security Framework initializing
[ 0.004441] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.004688] AppArmor: AppArmor initialized
[ 0.004711] TOMOYO Linux initialized
[ 0.004832] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linea r)
[ 0.004856] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.006300] CPU: Testing write buffer coherency: ok
[ 0.006879] /cpus/cpu@0 missing clock-frequency property
[ 0.006918] /cpus/cpu@1 missing clock-frequency property
[ 0.006935] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.008279] Setting up static identity map for 0x40300000 - 0x403000ac
[ 0.009543] rcu: Hierarchical SRCU implementation.
[ 0.012129] EFI services will not be available.
[ 0.012823] smp: Bringing up secondary CPUs ...
[ 0.024053] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.024327] smp: Brought up 1 node, 2 CPUs
[ 0.024354] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.024364] CPU: All CPU(s) started in HYP mode.
[ 0.024372] CPU: Virtualization extensions available.
[ 0.025511] devtmpfs: initialized
[ 0.034631] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.035035] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
[ 0.035088] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.039893] pinctrl core: initialized pinctrl subsystem
[ 0.041603] DMI not present or invalid.
[ 0.042217] NET: Registered protocol family 16
[ 0.044986] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.046270] audit: initializing netlink subsys (disabled)
[ 0.048449] thermal_sys: Registered thermal governor 'fair_share'
[ 0.048464] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.048483] thermal_sys: Registered thermal governor 'step_wise'
[ 0.048493] thermal_sys: Registered thermal governor 'user_space'
[ 0.048503] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.048979] No ATAGs?
[ 0.049107] audit: type=2000 audit(0.036:1): state=initialized audit_enabled= 0 res=1
[ 0.049221] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.049235] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.050548] Serial: AMBA PL011 UART driver
[ 0.083974] Kprobes globally optimized
[ 1.651112] iommu: Default domain type: Translated
[ 1.652483] vgaarb: loaded
[ 1.653660] mc: Linux media interface: v0.10
[ 1.653744] videodev: Linux video capture interface: v2.00
[ 1.656172] NetLabel: Initializing
[ 1.656200] NetLabel: domain hash size = 128
[ 1.656209] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 1.656347] NetLabel: unlabeled traffic allowed by default
[ 1.656927] clocksource: Switched to clocksource arch_sys_counter
[ 1.744531] VFS: Disk quotas dquot_6.6.0
[ 1.744697] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.745789] AppArmor: AppArmor Filesystem Enabled
[ 1.760215] NET: Registered protocol family 2
[ 1.760467] IP idents hash table entries: 16384 (order: 5, 131072 bytes, line ar)
[ 1.762555] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.762625] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.762744] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.762875] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.763094] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.763180] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.763900] NET: Registered protocol family 1
[ 1.763958] NET: Registered protocol family 44
[ 1.763988] PCI: CLS 0 bytes, default 64
[ 1.764782] Trying to unpack rootfs image as initramfs...
[ 3.648206] Freeing initrd memory: 22100K
[ 3.648709] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[ 3.649180] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counter s available
[ 3.651715] Initialise system trusted keyrings
[ 3.651798] Key type blacklist registered
[ 3.652241] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 3.660516] zbud: loaded
[ 3.662054] integrity: Platform Keyring initialized
[ 3.662100] Key type asymmetric registered
[ 3.662113] Asymmetric key parser 'x509' registered
[ 3.662333] bounce: pool size: 64 pages
[ 3.662432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 50)
[ 3.662834] io scheduler mq-deadline registered
[ 3.671547] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 3.693795] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[ 3.697351] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dum my regulator
[ 3.698296] printk: console [ttyS0] disabled
[ 3.718555] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 56, base_baud = 15 00000) is a U6_16550A
[ 4.481364] printk: console [ttyS0] enabled
[ 4.486965] sun4i-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dum my regulator
[ 4.516334] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 57, base_baud = 15 00000) is a U6_16550A
[ 4.526541] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pi not found, using dum my regulator
[ 4.555816] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 58, base_baud = 15 00000) is a U6_16550A
[ 4.566598] Serial: AMBA driver
[ 4.571571] STM32 USART driver initialized
[ 4.579418] libphy: Fixed MDIO Bus: probed
[ 4.584674] mousedev: PS/2 mouse device common for all mice
[ 4.593474] sunxi-rtc 1c20d00.rtc: registered as rtc0
[ 4.598633] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01T00:00:1 5 UTC (15)
[ 4.610322] ledtrig-cpu: registered to indicate activity on CPUs
[ 4.618432] NET: Registered protocol family 10
[ 4.658092] Segment Routing with IPv6
[ 4.662099] mip6: Mobile IPv6
[ 4.665136] NET: Registered protocol family 17
[ 4.669988] mpls_gso: MPLS GSO support
[ 4.673882] ThumbEE CPU extension supported.
[ 4.678235] Registering SWP/SWPB emulation handler
[ 4.683372] registered taskstats version 1
[ 4.687544] Loading compiled-in X.509 certificates
[ 5.050423] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3d d27dfcc5cbb419ea1'
[ 5.059309] Loaded X.509 cert 'Debian Secure Boot Signer 2021 - linux: 4b6ef5 abca669825178e052c84667ccbc0531f8c'
[ 5.069713] zswap: loaded using pool lzo/zbud
[ 5.075116] Key type ._fscrypt registered
[ 5.079267] Key type .fscrypt registered
[ 5.083262] Key type fscrypt-provisioning registered
[ 5.088605] AppArmor: AppArmor sha1 policy hashing enabled
[ 5.127073] Freeing unused kernel memory: 2048K
[ 5.134308] Checked W+X mappings: passed, no W+X pages found
[ 5.140050] Run /init as init process
[ 5.537865] leds_gpio: module verification failed: signature and/or required key missing - tainting kernel
[ 5.743398] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0)
[ 5.770781] usbcore: registered new interface driver usbfs
[ 5.789424] axp20x-i2c 0-0034: AXP20x variant AXP209 found
[ 5.790227] usbcore: registered new interface driver hub
[ 5.812631] pps_core: LinuxPPS API ver. 1 registered
[ 5.817719] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
[ 5.821198] usbcore: registered new device driver usb
[ 5.849482] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.874640] ehci-platform: EHCI generic platform driver
[ 5.876161] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.912472] axp20x-i2c 0-0034: AXP20X driver loaded
[ 5.925793] PTP clock support registered
[ 5.940369] ohci-platform: OHCI generic platform driver
[ 6.003222] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dum my regulator
[ 6.037433] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found
[ 6.044043] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found
[ 6.079931] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[ 6.099486] sun7i-dwmac 1c50000.ethernet: no reset control found
[ 6.145685] vdd-rtc: supplied by regulator-dummy
[ 6.156461] avcc: supplied by regulator-dummy
[ 6.172765] ldo3: supplied by regulator-dummy
[ 6.177660] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not set
[ 6.185949] ldo4: supplied by regulator-dummy
[ 6.195034] ldo5: supplied by regulator-dummy
[ 6.201255] vdd-cpu: supplied by regulator-dummy
[ 6.207735] vdd-int-dll: supplied by regulator-dummy
[ 6.225684] sun7i-dwmac 1c50000.ethernet: Version ID not available
[ 6.233542] sun7i-dwmac 1c50000.ethernet: DWMAC1000
[ 6.238693] sun7i-dwmac 1c50000.ethernet: DMA HW capability register supporte d
[ 6.246071] sun7i-dwmac 1c50000.ethernet: Normal descriptors
[ 6.251785] sun7i-dwmac 1c50000.ethernet: Ring mode enabled
[ 6.261769] libphy: stmmac: probed
[ 6.322959] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 6.358870] bcm53xx stmmac-0:1e: found switch: BCM53125, rev 4
[ 6.375046] bcm53xx stmmac-0:1e: failed to register switch: -517
Starting system log daemon: syslogd, klogd.
haveged: command socket is listening at fd 3