--- Begin Message ---
- To: submit@bugs.debian.org
- Subject: [d-i daily 2016-02-24] [armhf] Installation report: Olimex A20-SOM-EVB
- From: Karsten Merker <merker@debian.org>
- Date: Wed, 24 Feb 2016 21:39:30 +0100
- Message-id: <20160224203930.GA3698@excalibur.cnev.de>
Package: installation-reports
Boot method: netboot SD card image
Image version:
https://d-i.debian.org/daily-images/armhf/20160224-00:38/netboot/SD-card-images/firmware.A20-Olimex-SOM-EVB.img.gz
https://d-i.debian.org/daily-images/armhf/20160224-00:38/netboot/SD-card-images/partition.img.gz
Date: 2016-02-24
Machine: Olimex A20-SOM-EVB
Processor: Allwinner A20 (dual-core ARM cortex-a7)
Memory: 1GB
Installed Debian suite: sid (by passing "suite=sid" to the installer)
Installation Target: a 16GB Micro-SD card
Console device: serial console
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
Support for this board has been introduced in kernel 4.4, which
is currently only available in sid. Therefore one must select to
install sid instead of stretch for the time being.
The board hardware supports gigabit ethernet, but when connected
to a gigabit switch, I have noticed packet corruption and lots of
TCP retransmissions. When connected to a 100MBit switch,
everything works flawlessly. This is a known problem with
mainline u-boot and the mainline kernel on this board and not
specific to Debian. Similar issues have in the past also been
seen on some other A20-based boards - the solution in those cases
has been configuring a small GMAC transmit delay value in u-boot,
but my experiments in this regard haven't yet been successfull on
the A20-SOM-EVB.
When trying to reboot the system at the end of the installation,
the kernel prints "reboot: Restarting system" and then hangs.
I have run three test installations to check whether this was
a one-off effect, but the hang has occured all three times.
Interestingly the problem doesn't occur in the installed system;
reboots work flawlessly there.
Full boot log for reference:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-1-armmp-lpae (debian-kernel@lists.debian.org) (gcc version 4.9.3 (Debian 4.9.3-12) ) #1 SMP Debian 4.4.2-3 (2016-02-21)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=30c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Olimex A20-Olimex-SOM-EVB
[ 0.000000] Forcing write-allocate cache policy for SMP
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0b4a980, node_mem_map ef6f9000
[ 0.000000] DMA zone: 1728 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:31
[ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ef6c7000 s19916 r8192 d21044 u49152
[ 0.000000] pcpu-alloc: s19916 r8192 d21044 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: console=ttyS0,115200 quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1011824K/1048576K available (7281K kernel code, 897K rwdata, 2504K rodata, 908K init, 392K bss, 36752K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc09966fc (9786 kB)
.init : 0xc0997000 - 0xc0a7a000 ( 908 kB)
.data : 0xc0a7a000 - 0xc0b5a6a8 ( 898 kB)
.bss : 0xc0b5d000 - 0xc0bbf204 ( 393 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000022] Switching to timer-based delay loop, resolution 41ns
[ 0.002014] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002743] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 12741736309 ns
[ 0.003428] Console: colour dummy device 80x30
[ 0.003471] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.003487] pid_max: default: 32768 minimum: 301
[ 0.003644] Security Framework initialized
[ 0.003659] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.003695] AppArmor: AppArmor disabled by boot time parameter
[ 0.003844] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.003859] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004782] Initializing cgroup subsys io
[ 0.004817] Initializing cgroup subsys memory
[ 0.004890] Disabling memory control group subsystem
[ 0.004899] Initializing cgroup subsys devices
[ 0.004916] Initializing cgroup subsys freezer
[ 0.004941] Initializing cgroup subsys net_cls
[ 0.004956] Initializing cgroup subsys perf_event
[ 0.004974] Initializing cgroup subsys net_prio
[ 0.004990] Initializing cgroup subsys pids
[ 0.005063] CPU: Testing write buffer coherency: ok
[ 0.005115] ftrace: allocating 25492 entries in 75 pages
[ 0.046281] /cpus/cpu@0 missing clock-frequency property
[ 0.046317] /cpus/cpu@1 missing clock-frequency property
[ 0.046333] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.046428] Setting up static identity map for 0x400082c0 - 0x40008358
[ 0.052334] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.052471] Brought up 2 CPUs
[ 0.052498] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.052506] CPU: All CPU(s) started in HYP mode.
[ 0.052511] CPU: Virtualization extensions available.
[ 0.053148] devtmpfs: initialized
[ 0.061585] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.062506] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.062955] pinctrl core: initialized pinctrl subsystem
[ 0.064670] NET: Registered protocol family 16
[ 0.065023] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.075221] No ATAGs?
[ 0.075274] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.075289] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.076687] Serial: AMBA PL011 UART driver
[ 0.098243] reg-fixed-voltage ahci-5v: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
[ 0.098389] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[ 0.098430] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[ 0.101501] vgaarb: loaded
[ 0.102698] media: Linux media interface: v0.10
[ 0.102784] Linux video capture interface: v2.00
[ 0.102907] pps_core: LinuxPPS API ver. 1 registered
[ 0.102916] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.102948] PTP clock support registered
[ 0.104930] clocksource: Switched to clocksource arch_sys_counter
[ 0.165092] NET: Registered protocol family 2
[ 0.165976] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.166073] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.166201] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.166296] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.166356] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.166786] NET: Registered protocol family 1
[ 0.166856] PCI: CLS 0 bytes, default 64
[ 0.167451] Unpacking initramfs...
[ 1.327038] Freeing initrd memory: 14472K (c91de000 - ca000000)
[ 1.327851] kvm [1]: interrupt-controller@1c84000 IRQ46
[ 1.328305] kvm [1]: timer IRQ19
[ 1.328333] kvm [1]: Hyp mode initialized successfully
[ 1.329256] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 1.331172] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.331313] audit: initializing netlink subsys (disabled)
[ 1.331411] audit: type=2000 audit(1.312:1): initialized
[ 1.332831] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.333010] zbud: loaded
[ 1.333378] VFS: Disk quotas dquot_6.6.0
[ 1.333474] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.336029] bounce: pool size: 64 pages
[ 1.336171] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.336392] io scheduler noop registered
[ 1.336413] io scheduler deadline registered
[ 1.336454] io scheduler cfq registered (default)
[ 1.341103] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 1.355107] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.357575] console [ttyS0] disabled
[ 1.377895] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 40, base_baud = 1500000) is a U6_16550A
[ 1.388977] console [ttyS0] enabled
[ 1.389473] Serial: AMBA driver
[ 1.393570] mousedev: PS/2 mouse device common for all mice
[ 1.395709] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[ 1.395728] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 1.397617] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.399325] NET: Registered protocol family 10
[ 1.400435] mip6: Mobile IPv6
[ 1.400472] NET: Registered protocol family 17
[ 1.400506] mpls_gso: MPLS GSO support
[ 1.401111] ThumbEE CPU extension supported.
[ 1.401154] Registering SWP/SWPB emulation handler
[ 1.402247] registered taskstats version 1
[ 1.402417] zswap: loaded using pool lzo/zbud
[ 1.405257] sunxi-rtc 1c20d00.rtc: setting system clock to 2016-02-24 19:45:28 UTC (1456343128)
[ 1.411397] PM: Hibernation image not present or could not be loaded.
[ 1.411447] vcc3v0: disabling
[ 1.411459] vcc3v3: disabling
[ 1.411469] vcc5v0: disabling
[ 1.411477] ahci-5v: disabling
[ 1.411490] usb1-vbus: disabling
[ 1.411499] usb2-vbus: disabling
[ 1.413248] Freeing unused kernel memory: 908K (c0997000 - c0a7a000)
[ 1.499362] random: systemd-udevd urandom read with 0 bits of entropy available
[ 1.775264] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
[ 1.782534] SCSI subsystem initialized
[ 1.788431] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 1.821770] libata version 3.00 loaded.
[ 1.827553] sunxi-mmc 1c0f000.mmc: base:0xf0924000 irq:26
[ 1.869134] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 1.869167] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 1.869256] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.869275] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 1.871327] scsi host0: ahci-sunxi
[ 1.871874] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 30
[ 1.874090] sun7i-dwmac 1c50000.ethernet: no regulator found
[ 1.874211] sun7i-dwmac 1c50000.ethernet: no reset control found
[ 1.874225] Ring mode enabled
[ 1.874234] No HW DMA feature register supported
[ 1.874242] Normal descriptors
[ 1.874248] TX Checksum insertion supported
[ 1.888585] libphy: stmmac: probed
[ 1.888616] eth0: PHY ID 001cc912 at 1 IRQ POLL (stmmac-0:01) active
[ 1.893218] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.895947] mmc0: new high speed SDHC card at address 0007
[ 1.898644] mmcblk0: mmc0:0007 SD16G 14.6 GiB
[ 1.903873] mmcblk0: p1 p2 p3 < p5 >
[ 2.193069] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.276349] PM: Starting manual resume from disk
[ 2.276385] PM: Hibernation image partition 179:5 present
[ 2.276394] PM: Looking for hibernation image.
[ 2.277548] PM: Image not found (code -22)
[ 2.277564] PM: Hibernation image not present or could not be loaded.
[ 2.508554] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.052104] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 3.052865] systemd[1]: Detected architecture arm.
[ 3.062054] systemd[1]: Set hostname to <a20-som-evb>.
[ 3.491807] systemd[1]: Listening on udev Kernel Socket.
[ 3.492289] systemd[1]: Reached target Remote File Systems (Pre).
[ 3.493761] systemd[1]: Created slice System Slice.
[ 3.493930] systemd[1]: Reached target Encrypted Volumes.
[ 3.494927] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 3.495776] systemd[1]: Created slice User and Session Slice.
[ 3.496139] systemd[1]: Listening on Journal Socket (/dev/log).
[ 3.497384] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 3.498558] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.499008] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 3.499119] systemd[1]: Reached target Remote File Systems.
[ 3.499442] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.499715] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 3.500003] systemd[1]: Listening on Journal Socket.
[ 3.517397] systemd[1]: Mounting Huge Pages File System...
[ 3.523301] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 3.528632] systemd[1]: Mounting POSIX Message Queue File System...
[ 3.534551] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 3.540175] systemd[1]: Mounting Debug File System...
[ 3.570938] systemd[1]: Starting Load Kernel Modules...
[ 3.591975] systemd[1]: Listening on Process Core Dump Socket.
[ 3.592163] systemd[1]: Reached target Paths.
[ 3.592290] systemd[1]: Reached target Slices.
[ 3.600054] systemd[1]: Created slice system-getty.slice.
[ 3.600548] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 3.601600] systemd[1]: Listening on udev Control Socket.
[ 3.602020] systemd[1]: Listening on Syslog Socket.
[ 3.618161] systemd[1]: Listening on Journal Audit Socket.
[ 3.646232] systemd[1]: Starting Journal Service...
[ 3.685929] systemd[1]: Mounted Huge Pages File System.
[ 3.686304] systemd[1]: Mounted POSIX Message Queue File System.
[ 3.686634] systemd[1]: Mounted Debug File System.
[ 3.701875] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 3.707462] systemd[1]: Started Load Kernel Modules.
[ 3.710919] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 3.734348] systemd[1]: Started Remount Root and Kernel File Systems.
[ 3.824187] systemd[1]: Started Journal Service.
[ 4.686453] systemd-journald[166]: Received request to flush runtime journal from PID 1
[ 5.475628] usbcore: registered new interface driver usbfs
[ 5.475633] sun4i-ss 1c15000.crypto-engine: no reset control found
[ 5.475737] usbcore: registered new interface driver hub
[ 5.477322] sun4i-ss 1c15000.crypto-engine: Die ID 0
[ 5.498926] usbcore: registered new device driver usb
[ 5.507962] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.515109] ehci-platform: EHCI generic platform driver
[ 5.515982] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.519246] ohci-platform: OHCI generic platform driver
[ 5.541056] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 5.542091] ehci-platform 1c14000.usb: EHCI Host Controller
[ 5.542148] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[ 5.542357] ehci-platform 1c14000.usb: irq 27, io mem 0x01c14000
[ 5.553098] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 5.553569] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.553589] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.553642] usb usb1: Product: EHCI Host Controller
[ 5.553653] usb usb1: Manufacturer: Linux 4.4.0-1-armmp-lpae ehci_hcd
[ 5.553662] usb usb1: SerialNumber: 1c14000.usb
[ 5.554749] hub 1-0:1.0: USB hub found
[ 5.554898] hub 1-0:1.0: 1 port detected
[ 5.556000] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 5.556091] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[ 5.556379] ehci-platform 1c1c000.usb: irq 31, io mem 0x01c1c000
[ 5.565072] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 5.565524] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.565544] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.565554] usb usb2: Product: EHCI Host Controller
[ 5.565566] usb usb2: Manufacturer: Linux 4.4.0-1-armmp-lpae ehci_hcd
[ 5.565575] usb usb2: SerialNumber: 1c1c000.usb
[ 5.566634] hub 2-0:1.0: USB hub found
[ 5.566754] hub 2-0:1.0: 1 port detected
[ 5.568345] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 5.568407] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[ 5.568619] ohci-platform 1c14400.usb: irq 28, io mem 0x01c14400
[ 5.625447] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.625473] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.625483] usb usb3: Product: Generic Platform OHCI controller
[ 5.625494] usb usb3: Manufacturer: Linux 4.4.0-1-armmp-lpae ohci_hcd
[ 5.625504] usb usb3: SerialNumber: 1c14400.usb
[ 5.629096] hub 3-0:1.0: USB hub found
[ 5.629190] hub 3-0:1.0: 1 port detected
[ 5.632061] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 5.632133] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 5.632339] ohci-platform 1c1c400.usb: irq 32, io mem 0x01c1c400
[ 5.689499] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.689527] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.689537] usb usb4: Product: Generic Platform OHCI controller
[ 5.689548] usb usb4: Manufacturer: Linux 4.4.0-1-armmp-lpae ohci_hcd
[ 5.689558] usb usb4: SerialNumber: 1c1c400.usb
[ 5.691390] hub 4-0:1.0: USB hub found
[ 5.691499] hub 4-0:1.0: 1 port detected
[ 5.693346] axp20x 0-0034: AXP20x variant AXP209 found
[ 5.712319] axp20x 0-0034: AXP20X driver loaded
[ 5.942164] Adding 685052k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:685052k SSFS
[ 5.990168] input: axp20x-pek as /devices/platform/soc@01c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[ 6.287646] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
[ 6.301215] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 6.690269] RX IPC Checksum Offload disabled
[ 6.690300] No MAC Management Counters available
[ 8.677277] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 9.975783] random: nonblocking pool is initialized
Regards,
Karsten
--
Gem. Par. 28 Abs. 4 Bundesdatenschutzgesetz widerspreche ich der Nutzung
sowie der Weitergabe meiner personenbezogenen Daten für Zwecke der
Werbung sowie der Markt- oder Meinungsforschung.
--- End Message ---