On Wed, May 15, 2019 at 08:06:53AM -0700, Vagrant Cascadian wrote:
> On 2019-05-15, Domenico Andreoli wrote:
> > Scanning mmc 0:2...
> > Found /boot/extlinux/extlinux.conf
> > Retrieving file: /boot/extlinux/extlinux.conf
> > 753 bytes read in 12 ms (60.5 KiB/s)
> > U-Boot menu
> > 1: Debian GNU/Linux kernel 4.19.0-4-arm64
> > 2: Debian GNU/Linux kernel 4.19.0-4-arm64 (rescue target)
> > Enter choice: 1: Debian GNU/Linux kernel 4.19.0-4-arm64
>
> To test flash-kernel's boot.scr, you'll need to remove or disable
> checking for extlinux.conf, since that comes before loading the boot.scr
> that flash-kernel produces.
Right, sharp eye!
>
> From the u-boot prompt unset the the variable that checks for extlinux:
>
> setenv scan_dev_for_extlinux false
>
> Alternately, remove /boot/extlinux/extlinux.conf and reboot.
Ok, uninstalled u-boot-menu and grub packages (and all the related
config & co files). Emptied the first partition and moved /boot into it.
Now the system boots without manual intervention, no user/grub clutters
the bootlog any more ;)
U-Boot SPL 2019.01+dfsg-6 (May 12 2019 - 01:20:19 +0000)
DRAM: 1024 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.0(debug):
NOTICE: BL31: Built : 23:33:29, Nov 27 2018
NOTICE: BL31: Detected Allwinner H5 SoC (1718)
NOTICE: BL31: Found U-Boot DTB at 0x407f100, model: FriendlyARM NanoPi NEO 2
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
NOTICE: BL31: PMIC: Defaulting to PortL GPIO according to H5 reference design.
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
U-Boot 2019.01+dfsg-6 (May 12 2019 - 01:20:19 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: FriendlyARM NanoPi NEO 2
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Loading Environment from FAT... Unable to use mmc 0:1... In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
2228 bytes read in 5 ms (434.6 KiB/s)
## Executing script at 4fc00000
18558832 bytes read in 824 ms (21.5 MiB/s)
16815 bytes read in 10 ms (1.6 MiB/s)
24721329 bytes read in 1092 ms (21.6 MiB/s)
Booting Debian 4.19.0-4-arm64 from mmc 0:1...
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
EHCI failed to shut down host controller.
EHCI failed to shut down host controller.
Loading Ramdisk to 4886c000, end 49fff7b1 ... OK
Loading Device Tree to 0000000048864000, end 000000004886b1ae ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 4.19.0-4-arm64 (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-2)) #1 SMP Debian 4.19.28-2 (2019-03-15)
[ 0.000000] Machine model: FriendlyARM NanoPi NEO 2
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 64 MiB at 0x000000007c000000
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0x7bfdd5c0-0x7bfded7f]
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4c0 with crng_init=0
[ 0.000000] percpu: Embedded 24 pages/cpu @(____ptrval____) s60120 r8192 d29992 u98304
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: console=ttyS0,115200 panic=7
[ 0.000000] Memory: 923100K/1048576K available (8828K kernel code, 1610K rwdata, 2800K rodata, 4864K init, 530K bss, 59940K reserved, 65536K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 33059 entries in 130 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000156] Console: colour dummy device 80x25
[ 0.000283] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.000297] pid_max: default: 32768 minimum: 301
[ 0.000448] Security Framework initialized
[ 0.000458] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.000551] AppArmor: AppArmor initialized
[ 0.001205] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.001543] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.001596] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.001616] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.003355] ASID allocator initialised with 32768 entries
[ 0.003479] rcu: Hierarchical SRCU implementation.
[ 0.005716] EFI services will not be available.
[ 0.006100] smp: Bringing up secondary CPUs ...
[ 0.007537] Detected VIPT I-cache on CPU1
[ 0.007603] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.008701] Detected VIPT I-cache on CPU2
[ 0.008740] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.009729] Detected VIPT I-cache on CPU3
[ 0.009763] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.009853] smp: Brought up 1 node, 4 CPUs
[ 0.009878] SMP: Total of 4 processors activated.
[ 0.009888] CPU features: detected: 32-bit EL0 Support
[ 0.013071] CPU: All CPU(s) started at EL2
[ 0.013094] alternatives: patching kernel code
[ 0.014669] devtmpfs: initialized
[ 0.019071] Registered cp15_barrier emulation handler
[ 0.019090] Registered setend emulation handler
[ 0.019370] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.019412] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.022106] pinctrl core: initialized pinctrl subsystem
[ 0.023038] DMI not present or invalid.
[ 0.023485] NET: Registered protocol family 16
[ 0.023886] audit: initializing netlink subsys (disabled)
[ 0.024074] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[ 0.025146] cpuidle: using governor ladder
[ 0.025170] cpuidle: using governor menu
[ 0.025273] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[ 0.025284] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.026849] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.027182] Serial: AMBA PL011 UART driver
[ 0.038381] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.039624] ACPI: Interpreter disabled.
[ 0.040079] vgaarb: loaded
[ 0.040325] pps_core: LinuxPPS API ver. 1 registered
[ 0.040332] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.040351] PTP clock support registered
[ 0.040388] EDAC MC: Ver: 3.0.0
[ 0.041888] clocksource: Switched to clocksource arch_sys_counter
[ 0.106103] VFS: Disk quotas dquot_6.6.0
[ 0.106183] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.106800] AppArmor: AppArmor Filesystem Enabled
[ 0.107017] pnp: PnP ACPI: disabled
[ 0.115570] NET: Registered protocol family 2
[ 0.116217] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 0.116297] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.116410] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.116590] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.116734] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.116779] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.116997] NET: Registered protocol family 1
[ 0.117023] NET: Registered protocol family 44
[ 0.117282] Unpacking initramfs...
[ 1.830545] Freeing initrd memory: 24140K
[ 1.831191] kvm [1]: 8-bit VMID
[ 1.831817] kvm [1]: vgic interrupt IRQ1
[ 1.831961] kvm [1]: Hyp mode initialized successfully
[ 1.834833] Initialise system trusted keyrings
[ 1.835009] workingset: timestamp_bits=44 max_order=18 bucket_order=0
[ 1.841626] zbud: loaded
[ 1.842328] pstore: using deflate compression
[ 2.710584] Key type asymmetric registered
[ 2.710600] Asymmetric key parser 'x509' registered
[ 2.710666] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 2.710848] io scheduler noop registered
[ 2.710856] io scheduler deadline registered
[ 2.711083] io scheduler cfq registered (default)
[ 2.711091] io scheduler mq-deadline registered
[ 2.715046] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 2.719315] sun50i-h5-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 2.720213] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 2.724891] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.726509] console [ttyS0] disabled
[ 2.747035] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 21, base_baud = 1500000) is a U6_16550A
[ 3.437770] console [ttyS0] enabled
[ 3.441769] Serial: AMBA driver
[ 3.445180] msm_serial: driver initialized
[ 3.449827] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 3.456495] mousedev: PS/2 mouse device common for all mice
[ 3.462766] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0
[ 3.469567] sun6i-rtc 1f00000.rtc: RTC enabled
[ 3.475104] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.482799] NET: Registered protocol family 10
[ 3.528330] Segment Routing with IPv6
[ 3.532124] mip6: Mobile IPv6
[ 3.535108] NET: Registered protocol family 17
[ 3.539685] mpls_gso: MPLS GSO support
[ 3.544176] registered taskstats version 1
[ 3.548282] Loading compiled-in X.509 certificates
[ 3.751831] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 3.760605] Loaded X.509 cert 'Debian Secure Boot Signer: 00a7468def'
[ 3.767147] zswap: loaded using pool lzo/zbud
[ 3.771652] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.785078] sun6i-rtc 1f00000.rtc: setting system clock to 2019-05-15 16:04:57 UTC (1557936297)
[ 3.803735] Freeing unused kernel memory: 4864K
[ 3.822004] Run /init as init process
Loading, please wait...
Starting version 241
[ 4.164533] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2
[ 4.179930] sun4i-usb-phy 1c19400.phy: Linked as a consumer to regulator.3
[ 4.202307] usbcore: registered new interface driver usbfs
[ 4.207927] usbcore: registered new interface driver hub
[ 4.213480] usbcore: registered new device driver usb
[ 4.232323] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.247895] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 4.248296] libphy: Fixed MDIO Bus: probed
[ 4.257108] ehci-platform: EHCI generic platform driver
[ 4.257123] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.262711] ehci-platform 1c1a000.usb: EHCI Host Controller
[ 4.274552] ohci-platform: OHCI generic platform driver
[ 4.280414] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[ 4.287250] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 4.290129] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[ 4.297114] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[ 4.314128] ohci-platform 1c1a400.usb: irq 11, io mem 0x01c1a400
[ 4.324791] ehci-platform 1c1a000.usb: irq 10, io mem 0x01c1a000
[ 4.332122] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[ 4.332789] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 4.338074] dwmac-sun8i 1c30000.ethernet: Linked as a consumer to regulator.1
[ 4.348444] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[ 4.348745] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 4.355858] usb_phy_generic usb_phy_generic.0.auto: Linked as a consumer to regulator.0
[ 4.361968] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.371112] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 4.378263] usb usb1: Product: EHCI Host Controller
[ 4.378273] usb usb1: Manufacturer: Linux 4.19.0-4-arm64 ehci_hcd
[ 4.402244] usb usb1: SerialNumber: 1c1a000.usb
[ 4.407527] hub 1-0:1.0: USB hub found
[ 4.411469] hub 1-0:1.0: 1 port detected
[ 4.416029] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[ 4.416238] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 4.416289] ehci-platform 1c1d000.usb: EHCI Host Controller
[ 4.437801] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.445022] usb usb2: Product: Generic Platform OHCI controller
[ 4.450952] usb usb2: Manufacturer: Linux 4.19.0-4-arm64 ohci_hcd
[ 4.457055] usb usb2: SerialNumber: 1c1a400.usb
[ 4.462237] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 50006 (expect 58000)
[ 4.462302] hub 2-0:1.0: USB hub found
[ 4.471594] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[ 4.475356] hub 2-0:1.0: 1 port detected
[ 4.482547] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[ 4.486943] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 4
[ 4.487174] ohci-platform 1c1d400.usb: Generic Platform OHCI controller
[ 4.487197] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 5
[ 4.487565] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 4.487572] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.487577] usb usb3: Product: MUSB HDRC host driver
[ 4.487583] usb usb3: Manufacturer: Linux 4.19.0-4-arm64 musb-hcd
[ 4.487588] usb usb3: SerialNumber: musb-hdrc.1.auto
[ 4.488203] hub 3-0:1.0: USB hub found
[ 4.488235] hub 3-0:1.0: 1 port detected
[ 4.493732] dwmac-sun8i 1c30000.ethernet: COE Type 2
[ 4.508121] mmc0: host does not support reading read-only switch, assuming write-enable
[ 4.515850] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[ 4.515856] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[ 4.515865] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[ 4.542436] mmc0: new high speed SDHC card at address e624
[ 4.548059] libphy: stmmac: probed
[ 4.548175] ohci-platform 1c1d400.usb: irq 13, io mem 0x01c1d400
[ 4.548230] ehci-platform 1c1d000.usb: irq 12, io mem 0x01c1d000
[ 4.553935] mmcblk0: mmc0:e624 SL08G 7.40 GiB
[ 4.555877] dwmac-sun8i 1c30000.ethernet: Found internal PHY node
[ 4.561935] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00
[ 4.568354] libphy: mdio_mux: probed
[ 4.575089] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 4.580577] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY
[ 4.580579] mmcblk0: p1 p2
[ 4.586190] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.586197] usb usb4: Product: EHCI Host Controller
[ 4.586203] usb usb4: Manufacturer: Linux 4.19.0-4-arm64 ehci_hcd
[ 4.586208] usb usb4: SerialNumber: 1c1d000.usb
[ 4.586847] hub 4-0:1.0: USB hub found
[ 4.591716] dwmac-sun8i 1c30000.ethernet: Powering internal PHY
[ 4.595146] hub 4-0:1.0: 1 port detected
[ 4.611227] libphy: mdio_mux: probed
[ 4.612250] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 4.617737] dwmac-sun8i 1c30000.ethernet: Switch mux to external PHY
[ 4.623839] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.623846] usb usb5: Product: Generic Platform OHCI controller
[ 4.623851] usb usb5: Manufacturer: Linux 4.19.0-4-arm64 ohci_hcd
[ 4.623857] usb usb5: SerialNumber: 1c1d400.usb
[ 4.625144] hub 5-0:1.0: USB hub found
[ 4.727031] hub 5-0:1.0: 1 port detected
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -a -C0 /dev/mmcblk0p2
/dev/mmcblk0p2: clean, 25420/452480 files, 301027/1808896 blocks[ 4.956496] random: fast init done
done.
[ 5.148933] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 6.045684] systemd[1]: Inserted module 'autofs4'
[ 6.105016] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 6.126899] systemd[1]: Detected architecture arm64.
Welcome to Debian GNU/Linux buster/sid!
[ 6.158814] systemd[1]: Set hostname to <n2>.
[ 6.719559] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.731261] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.741777] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ 6.762551] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.769681] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 6.786482] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 6.803307] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 6.822054] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 6.838031] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 6.854586] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ OK ] Listening on Journal Socket.
Mounting Kernel Debug File System...
Starting udev Coldplug all Devices...
Starting Load Kernel Modules...
Starting Create list of re…odes for the current kernel...
[ OK ] Listening on Journal Socket (/dev/log).
Mounting POSIX Message Queue File System...
Mounting Huge Pages File System...
[ OK ] Listening on fsck to fsckd communication Socket.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
Starting Remount Root and Kernel File Systems...
[ OK ] Reached target Remote File Systems.
[ OK ] Created slice system-tor.slice.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 7.127928] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ OK ] Reached target Local Encrypted Volumes.
[ OK ] Reached target Paths.
[ OK ] Created slice system-getty.slice.
[ OK ] Listening on Syslog Socket.
Starting Journal Service...
[ OK ] Mounted Kernel Debug File System.
[ OK ] Started Load Kernel Modules.
[ OK ] Started Create list of req… nodes for the current kernel.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Huge Pages File System.
[ OK ] Started Remount Root and Kernel File Systems.
Starting Load/Save Random Seed...
Starting Create System Users...
Starting Apply Kernel Variables...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Started Create System Users.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Helper to synchronize boot up for ifupdown.
Starting Create Static Device Nodes in /dev...
[ 7.579210] systemd-journald[188]: Received request to flush runtime journal from PID 1
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Started udev Kernel Device Manager.
[ OK ] Found device /dev/ttyS0.
[ 8.035145] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 8.237293] cryptd: max_cpu_qlen set to 1000
[ OK ] Found device /dev/mmcblk0p1.
Starting File System Check on /dev/mmcblk0p1...
[ OK ] Started File System Check Daemon to report status.
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ OK ] Started File System Check on /dev/mmcblk0p1.
Mounting /boot...
[ 8.578824] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
[ 8.596615] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
Starting Firehol stateful …ltering firewall for humans...
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Initialization.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Login Service...
Starting System Logging Service...
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Reached target Timers.
[ OK ] Started System Logging Service.
[ OK ] Started Login Service.
[ OK ] Started Firehol stateful p…filtering firewall for humans.
[ OK ] Reached target Network (Pre).
[ OK ] Started ifup for eth0.
Starting Raise network interfaces...
[ OK ] Started Raise network interfaces.
[ OK ] Reached target Network.
Starting OpenBSD Secure Shell server...
Starting Permit User Sessions...
[ OK ] Reached target Network is Online.
Starting FireQOS traffic shaping for humans...
[ OK ] Started Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[ 13.850902] RTL8211E Gigabit Ethernet 0.2:07: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=0.2:07, irq=POLL)
[ 13.871136] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found
[ 13.878502] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available
[ 13.886234] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW
[ 13.893438] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ OK ] Started FireQOS traffic shaping for humans.
[ 19.006728] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 19.014955] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Debian GNU/Linux buster/sid n2 ttyS0
n2 login:
>
> live well,
> vagrant
thanks,
Domenico
--
3B10 0CA1 8674 ACBA B4FE FCD2 CE5B CF17 9960 DE13
Attachment:
signature.asc
Description: PGP signature