Bug#914813: kernel 3.4 works
On Thu, Dec 27, 2018 at 08:05:08AM +0100, Bernhard wrote:
>
> I made a test with a pre-built image from banana-pi.org.
> This is Debian 8 "Jessie" with a very old kernel 3.4.
> I assume, the famous sunxi-kernel.
> Here, the Ethernet works.
> The complete log during booting is attached.
> Hopefully, it helps.
>
> If i can do further tests, or if you need further informations: please let me know.
>
> Best regards
> Bernhard
>
> HELLO! BOOT0 is starting!
<snip/>
> [ 1.308][mmc]: mmc not find,so not exit
> HELLO! BOOT0 is starting!
<snip/>
> U-Boot 2011.09-rc1-00000-g4948cb4-dirty (Jul 11 2018 - 01:55:24) Allwinner Technology
<snip/>
> ** Invalid boot device **
> [ 4.579][mmc]: blkcnt should not be 0
> Loaded environment from uEnv.txt
> Running uenvcmd ...
> Banana Pi bpi-m3 chip: a83t Service: linux bpiuser: 720p
> [ 5.131][mmc]: blkcnt should not be 0
> ## Booting kernel from Legacy Image at 48000000 ...
> Image Name: Linux-3.4.39-BPI-M3-Kernel
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 7002512 Bytes = 6.7 MiB
> Load Address: 40008000
> Entry Point: 40008000
> Verifying Checksum ... OK
> ## Loading init Ramdisk from Legacy Image at 43100000 ...
> Image Name: uInitrd
> Image Type: ARM Linux RAMDisk Image (gzip compressed)
> Data Size: 5161148 Bytes = 4.9 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
> [ 5.327][mmc]: MMC Device 2 not found
> [ 5.331][mmc]: mmc not find,so not exit
> [ 5.335]
> Starting kernel ...
>
> [sun8i_fixup]: From boot, get meminfo:
>
Start: 0x40000000
>
Size: 2048MB
>
ion_carveout reserve: 96m 128m
>
ion_reserve_common: ion reserve: [0xb8000000, 0xc0000000]!
>
ion_cma reserve: 120m 176m 512m
>
ion_reserve_common: ion reserve: [0xa0000000, 0xc0000000]!
>
------sun8i_smp_init_ops----37-----
>
[ 0.000000] Booting Linux on physical CPU 0
> [ 0.000000] Initializing cgroup subsys cpuset
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 3.4.39-BPI-M3-Kernel (root@1a557e1c594c) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #3 SMP PREEMPT Wed Jul 11 01:55:51 UTC 2018
> [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
<snip/>
> [ 2.320816] [rfkill]: mod has no ls_int gpio
> [ 2.320830] [rfkill]: mod has no pcm_ch gpio
> [ 2.321375] [rfkill]: rfkill set power 0
<snip/>
> [ 17.939254] systemd[1]: Detected architecture arm.
>
> Welcome to [1mDebian GNU/Linux 9 (stretch)[0m!
>
> [ 17.982068] systemd[1]: Set hostname to <bpi-iot-ros-ai>.
<snip/>
> [ 26.486354] USB Serial support registered for GSM modem (1-port)
> [[0;32m OK [0m] Started Set console font and keymap.
> [[0;32m OK [0m] Found device /dev/ttyS0.
> [[0;32m OK [0m] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
> [[0;32m OK [0m] Reached target Sound Card.
> Starting Create Volatile Files and Directories...
> Starting Load/Save RF Kill Switch Status...
> [ 29.552854] gmac0: probed
> [ 29.600398] gmac0 gmac0: eth0: eth0: PHY ID 001cc915 at 0 IRQ poll (gmac0-0:00)
> [ 29.700631] [rfkill]: rfkill set power 0
> [[0;32m OK [0m] Started Create Volatile Files and Directories.
> [[0;32m OK [0m] Started Load/Save RF Kill Switch Status.
<snip/>
> [ 33.600389] PHY: gmac0-0:00 - Link is Up - 100/Full
> Starting Network Manager...
> Starting Accounts Service...
<snip/>
> [ 54.107624] rc.local[780]: My IP address is 192.168.2.150 2003:ca:bf4:5814:1842:4bff:fe49:9561
> Starting User Manager for UID 1000...
<snip/>
> Debian GNU/Linux 9 bpi-iot-ros-ai ttyS0
>
> bpi-iot-ros-ai login:
For some reason I assume that `RF Kill` does more then just wireless.
I don't know which way to go. Too many options.
Groeten
Geert Stappers
--
Leven en laten leven
Reply to: