Package: installation-reports Boot method: Installer bootet via USB Image version: http://cdimage.debian.org/cdimage/stretch_di_rc1/amd64/iso-cd/debian-stretch-DI-rc1-amd64-netinst.iso Date: 2017-01-18 09:45 Machine: SUPERMICRO X10SBA-L-O-P Processor: Intel Celeron J1900 (cpu family:6, model: 55, stepping:8) Memory: 4GB Partitions: Disk /dev/sda: 931,5 GiB, 1000204886016 bytes, 1953525168 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x51e39a8b Device Boot Start End Sectors Size Id Type /dev/sda1 * 2048 1945382911 1945380864 927,6G 83 Linux /dev/sda2 1945384958 1953523711 8138754 3,9G 5 Extended /dev/sda5 1945384960 1953523711 8138752 3,9G 82 Linux swap / Solaris Output of lspci -knn (or lspci -nn): 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor Z36xxx/Z37xxx Serie s SoC Transaction Register [8086:0f00] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor Z36xxx/Z37xxx Series SoC Transaction Register [15d9:0816] Kernel driver in use: iosf_mbi_pci 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor Z36xx x/Z37xxx Series Graphics & Display [8086:0f31] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor Z36xxx/Z37xxx Series Graphics & Display [15d9:0816] Kernel driver in use: i915 Kernel modules: i915 00:13.0 SATA controller [0106]: Intel Corporation Atom Processor E3800 Series SA TA AHCI Controller [8086:0f23] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor E3800 Series SATA AHC I Controller [15d9:0816] Kernel driver in use: ahci Kernel modules: ahci 00:1a.0 Encryption controller [1080]: Intel Corporation Atom Processor Z36xxx/Z3 7xxx Series Trusted Execution Engine [8086:0f18] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine [15d9:0816] 00:1c.0 PCI bridge [0604]: Intel Corporation Atom Processor E3800 Series PCI Exp ress Root Port 1 [8086:0f48] (rev 0e) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Atom Processor E3800 Series PCI Exp ress Root Port 3 [8086:0f4c] (rev 0e) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation Atom Processor E3800 Series PCI Exp ress Root Port 4 [8086:0f4e] (rev 0e) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Atom Processor Z36xxx/Z37xxx Se ries USB EHCI [8086:0f34] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor Z36xxx/Z37xxx Series USB EHCI [15d9:0816] Kernel driver in use: ehci-pci Kernel modules: ehci_pci 00:1f.0 ISA bridge [0601]: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Power Control Unit [8086:0f1c] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor Z36xxx/Z37xxx Series Power Control Unit [15d9:0816] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.3 SMBus [0c05]: Intel Corporation Atom Processor E3800 Series SMBus Contro ller [8086:0f12] (rev 0e) Subsystem: Super Micro Computer Inc Atom Processor E3800 Series SMBus Co ntroller [15d9:0816] Kernel driver in use: i801_smbus Kernel modules: i2c_i801 02:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Conne ction [8086:1533] (rev 03) Subsystem: Super Micro Computer Inc I210 Gigabit Network Connection [15d 9:1533] Kernel driver in use: igb Kernel modules: igb 03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Conne ction [8086:1533] (rev 03) Subsystem: Super Micro Computer Inc I210 Gigabit Network Connection [15d 9:1533] Kernel driver in use: igb Kernel modules: igb Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [O] Detect network card: [O] Configure network: [E] Detect CD: [ ] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Install base system: [E] Clock/timezone setup: [O] User/password setup: [O] Install tasks: [O] Install boot loader: [O] Overall install: [E] Comments/Problems: 1. ifconfig is not available I don't know if this is wanted or not, but I miss it 2. the renaming of the networkcards is buggy The board has 2 interfaces. One is always renamed to 'eno1' The second is renamed to 'rename2' or 'rename3' (very strange) dmesg | grep eth [ 3.610445] igb 0000:02:00.0: added PHC on eth0 [ 3.610450] igb 0000:02:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 0c:c4:7a:b5:5a:9c [ 3.610491] igb 0000:02:00.0: eth0: PBA No: 013000-000 [ 3.640493] igb 0000:03:00.0: added PHC on eth1 [ 3.640498] igb 0000:03:00.0: eth1: (PCIe:2.5Gb/s:Width x1) 0c:c4:7a:b5:5a:9d [ 3.640559] igb 0000:03:00.0: eth1: PBA No: 011000-000 [ 3.643096] igb 0000:02:00.0 eno1: renamed from eth0 [ 3.661095] igb 0000:03:00.0 rename3: renamed from eth1 3. Booting from disk takes very long (ca. 90 seconds) with a black screen No idea why. dmesg: [ 4.090351] sd 0:0:0:0: [sda] Write Protect is off [ 4.090357] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.090453] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO o r FUA [ 4.124658] sda: sda1 sda2 < sda5 > [ 4.127496] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.376746] usb 1-1.1: new low-speed USB device number 3 using ehci-pci [ 4.498408] usb 1-1.1: New USB device found, idVendor=0d62, idProduct=001c [ 4.498414] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.498417] usb 1-1.1: Product: USB Combo Keyboard [ 4.498420] usb 1-1.1: Manufacturer: Darfon [ 4.511808] hidraw: raw HID events driver (C) Jiri Kosina [ 4.527991] usbcore: registered new interface driver usbhid [ 4.527994] usbhid: USB HID core driver [ 4.531614] input: Darfon USB Combo Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1. 1/1-1.1:1.0/0003:0D62:001C.0001/input/input1 [ 4.589254] hid-generic 0003:0D62:001C.0001: input,hidraw0: USB HID v1.00 Keyboard [Darfon USB Combo Keyboard] on usb-0000:00:1d.0-1.1/input0 [ 4.592339] input: Darfon USB Combo Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1. 1/1-1.1:1.1/0003:0D62:001C.0002/input/input2 [ 4.649404] hid-generic 0003:0D62:001C.0002: input,hiddev0,hidraw1: USB HID v1.00 Device [Darf on USB Combo Keyboard] on usb-0000:00:1d.0-1.1/input1 [ 5.033980] clocksource: Switched to clocksource tsc [ 94.565678] PM: Starting manual resume from disk [ 94.565685] PM: Hibernation image partition 8:5 present [ 94.565687] PM: Looking for hibernation image. [ 94.566138] PM: Image not found (code -22) [ 94.566141] PM: Hibernation image not present or could not be loaded. [ 94.924092] random: fast init done [ 94.978975] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 95.899593] ip_tables: (C) 2000-2006 Netfilter Core Team [ 95.995040] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARM OR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 95.995413] systemd[1]: Detected architecture x86-64. This happens with a fresh installation. If I make a dist-upgrade from Jessie 8.7 to Stretch it boots in 8 seconds to the login prompt. Also the interface naming is working due to udev rules (I think so) If you have further questions: mail me :) Best regards, Bernd |