Package: installation-reports Boot method: followed instructions to load initrd.gz and zImage into memory per https://www.debian.org/releases/wheezy/armel/ch05s01.html.en#boot-firmware Image version: wheezy Date: 1/9/2017 14:30 MST Machine: Intel SS4000E Processor: ARM Memory: 256M Partitions: none Output of lspci -knn (or lspci -nn): not available Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [E] Detect network card: [ ] Configure network: [ ] Detect CD: [ ] Load installer modules: [ ] Detect hard drives: [ ] Partition hard drives: [ ] Install base system: [ ] Clock/timezone setup: [ ] User/password setup: [ ] Install tasks: [ ] Install boot loader: [ ] Overall install: [ ] Comments/Problems: Have tried several times and seem to meet same demise each time. I know wheezy is backlevel but I understand it is the last to support the SS4000E. The console output is below and it seems to be a problem with initrd at 0.172929 below. Thank you for any assistance. RedBoot> load -v -r -b 0x01800000 -m ymodem initrd.gz CRaw file loaded 0x01800000-0x01cc9a8e, assumed entry at 0x01800000 xyzModem - CRC mode, 1(SOH)/4903(STX)/0(CAN) packets, 3 retries RedBoot> load -v -r -b 0x01008000 -m ymodem zImage CRaw file loaded 0x01008000-0x01167347, assumed entry at 0x01008000 xyzModem - CRC mode, 1(SOH)/1405(STX)/0(CAN) packets, 4 retries RedBoot> exec -r 0x01800000 -c "console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000 BOOT_DEBUG=2" Using base address 0x01008000 and length 0x0015f348 Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0-4-iop32x (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 Debian 3.2.78-1 [ 0.000000] CPU: XScale-80219 [69052e20] revision 0 (ARMv5TE), cr=0000397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Lanner EM7210 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000 BOOT_DEBUG=2 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 251556k/251556k available, 10588k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xfe000000 ( 728 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0382854 (3563 kB) [ 0.000000] .init : 0xc0383000 - 0xc03a2000 ( 124 kB) [ 0.000000] .data : 0xc03a2000 - 0xc03d2d40 ( 196 kB) [ 0.000000] .bss : 0xc03d2d64 - 0xc0419248 ( 282 kB) [ 0.000000] NR_IRQS:32 [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000410] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656) [ 0.050067] pid_max: default: 32768 minimum: 301 [ 0.050384] Security Framework initialized [ 0.050551] Mount-cache hash table entries: 512 [ 0.051520] Initializing cgroup subsys cpuacct [ 0.051582] Initializing cgroup subsys memory [ 0.051647] Initializing cgroup subsys devices [ 0.051670] Initializing cgroup subsys freezer [ 0.051692] Initializing cgroup subsys net_cls [ 0.051714] Initializing cgroup subsys blkio [ 0.051771] Initializing cgroup subsys perf_event [ 0.051955] CPU: Testing write buffer coherency: ok [ 0.052751] hw perfevents: enabled with xscale1 PMU driver, 3 counters available [ 0.056286] devtmpfs: initialized [ 0.059550] print_constraints: dummy: [ 0.060315] NET: Registered protocol family 16 [ 0.065854] PCI: bus0: Fast back to back transfers disabled [ 0.068299] pci 0000:00:01.0: BAR 0: assigned [mem 0x80000000-0x8001ffff] [ 0.068355] pci 0000:00:01.0: BAR 1: assigned [mem 0x80020000-0x8003ffff] [ 0.068395] pci 0000:00:01.0: BAR 6: assigned [mem 0x80040000-0x8005ffff pref] [ 0.068432] pci 0000:00:02.0: BAR 0: assigned [mem 0x80060000-0x8007ffff] [ 0.068470] pci 0000:00:02.0: BAR 1: assigned [mem 0x80080000-0x8009ffff] [ 0.068509] pci 0000:00:02.0: BAR 6: assigned [mem 0x800a0000-0x800bffff pref] [ 0.068547] pci 0000:00:03.0: BAR 0: assigned [mem 0x800c0000-0x800c0fff 64bit] [ 0.068588] pci 0000:00:05.0: BAR 0: assigned [mem 0x800c1000-0x800c1fff] [ 0.068626] pci 0000:00:05.1: BAR 0: assigned [mem 0x800c2000-0x800c2fff] [ 0.068664] pci 0000:00:05.2: BAR 0: assigned [mem 0x800c3000-0x800c30ff] [ 0.068702] pci 0000:00:01.0: BAR 2: assigned [io 0x90000000-0x9000003f] [ 0.068739] pci 0000:00:02.0: BAR 2: assigned [io 0x90000040-0x9000007f] [ 0.074748] bio: create slab <bio-0> at 0 [ 0.076406] vgaarb: loaded [ 0.078169] Switching to clocksource iop_timer1 [ 0.138093] NET: Registered protocol family 2 [ 0.168030] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.170055] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.170609] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.170890] TCP: Hash tables configured (established 8192 bind 8192) [ 0.170915] TCP reno registered [ 0.170942] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.171005] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.171663] NET: Registered protocol family 1 [ 0.172929] Unpacking initramfs... [ 1.422112] Initramfs unpacking failed: read error [ 1.455918] Freeing initrd memory: 4096K [ 1.455951] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.457562] audit: initializing netlink socket (disabled) [ 1.457752] type=2000 audit(1.440:1): initialized [ 1.462375] VFS: Disk quotas dquot_6.5.2 [ 1.462654] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.463023] msgmni has been set to 499 [ 1.465029] alg: No test for stdrng (krng) [ 1.465465] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.465506] io scheduler noop registered [ 1.465527] io scheduler deadline registered [ 1.465616] io scheduler cfq registered (default) [ 1.478493] iop-adma iop-adma.0: Intel(R) IOP: ( cpy intr ) [ 1.498463] iop-adma iop-adma.1: Intel(R) IOP: ( cpy intr ) [ 1.499853] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.522366] serial8250.0: ttyS0 at MMIO 0xfe800000 (irq = 28) is a 16550A [ 1.998180] console [ttyS0] enabled [ 2.004546] physmap platform flash device: 02000000 at f0000000 [ 2.011423] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x00891c [ 2.021870] Intel/Sharp Extended Query Table at 0x010A [ 2.027055] Intel/Sharp Extended Query Table at 0x010A [ 2.032266] Intel/Sharp Extended Query Table at 0x010A [ 2.037467] Intel/Sharp Extended Query Table at 0x010A [ 2.042697] Intel/Sharp Extended Query Table at 0x010A [ 2.047920] Using buffer write method [ 2.051618] Using auto-unlock on power-up/resume [ 2.056254] cfi_cmdset_0001: Erase suspend on write enabled [ 2.062151] Searching for RedBoot partition table in physmap-flash.0 at offset 0x1fe0000 [ 2.196733] 10 RedBoot partitions found on MTD device physmap-flash.0 [ 2.203333] Creating 10 MTD partitions on "physmap-flash.0": [ 2.209084] 0x000000000000-0x000000040000 : "RedBoot" [ 2.217514] 0x000000040000-0x000000060000 : "log" [ 2.225767] 0x000000060000-0x0000000a0000 : "rammode" [ 2.234401] 0x0000000a0000-0x0000000c0000 : "naskey" [ 2.243025] 0x0000000c0000-0x0000002c0000 : "zImage" [ 2.251877] 0x0000002c0000-0x0000006c0000 : "ramdisk.gz" [ 2.260984] 0x0000006c0000-0x000001f40000 : "vendor" [ 2.270476] 0x000001f40000-0x000001fc0000 : "wmdata" [ 2.279016] 0x000001fc0000-0x000001fc1000 : "RedBoot config" [ 2.284722] mtd: partition "RedBoot config" doesn't end on an erase block -- force read-only [ 2.296702] 0x000001fe0000-0x000002000000 : "FIS directory" [ 2.307196] mousedev: PS/2 mouse device common for all mice [ 2.313102] i2c /dev entries driver [ 2.322131] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6 [ 2.335604] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 [ 2.348493] TCP cubic registered [ 2.351774] NET: Registered protocol family 17 [ 2.356327] Registering the dns_resolver key type [ 2.361216] XScale DSP coprocessor detected. [ 2.367389] registered taskstats version 1 [ 2.374340] rtc-rs5c372 0-0032: setting system clock to 2117-01-09 21:18:54 UTC (344703038) [ 2.382946] Initializing network drop monitor service [ 2.390292] Freeing init memory: 124K [ 3.088755] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3.095852] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3.488175] usbcore: registered new interface driver usbfs [ 3.558883] usbcore: registered new interface driver hub [ 3.578515] usbcore: registered new device driver usb [ 3.591432] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.678145] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.590982] e1000 0000:00:01.0: eth0: (PCI:33MHz:32-bit) 00:0e:0c:db:16:38 [ 4.597944] e1000 0000:00:01.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.618900] ehci_hcd 0000:00:05.2: EHCI Host Controller [ 4.624391] ehci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 1 [ 4.668603] ehci_hcd 0000:00:05.2: irq 27, io mem 0x800c3000 [ 4.688529] ehci_hcd 0000:00:05.2: USB 2.0 started, EHCI 1.00 [ 4.694548] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.701503] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.708785] usb usb1: Product: EHCI Host Controller [ 4.713685] usb usb1: Manufacturer: Linux 3.2.0-4-iop32x ehci_hcd [ 4.719822] usb usb1: SerialNumber: 0000:00:05.2 [ 4.772210] hub 1-0:1.0: USB hub found [ 4.776068] hub 1-0:1.0: 5 ports detected [ 4.799818] ohci_hcd 0000:00:05.0: OHCI Host Controller [ 4.805234] ohci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 2 [ 4.889907] ohci_hcd 0000:00:05.0: irq 30, io mem 0x800c1000 [ 5.003439] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 5.010401] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.017650] usb usb2: Product: OHCI Host Controller [ 5.022570] usb usb2: Manufacturer: Linux 3.2.0-4-iop32x ohci_hcd [ 5.028705] usb usb2: SerialNumber: 0000:00:05.0 [ 5.037455] hub 2-0:1.0: USB hub found [ 5.041438] hub 2-0:1.0: 3 ports detected [ 5.544475] e1000 0000:00:02.0: eth1: (PCI:33MHz:32-bit) 00:0e:0c:db:16:39 [ 5.551523] e1000 0000:00:02.0: eth1: Intel(R) PRO/1000 Network Connection [ 5.558918] ohci_hcd 0000:00:05.1: OHCI Host Controller [ 5.564436] ohci_hcd 0000:00:05.1: new USB bus registered, assigned bus number 3 [ 5.599201] ohci_hcd 0000:00:05.1: irq 29, io mem 0x800c2000 [ 5.721469] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 5.728425] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.735676] usb usb3: Product: OHCI Host Controller [ 5.740596] usb usb3: Manufacturer: Linux 3.2.0-4-iop32x ohci_hcd [ 5.746716] usb usb3: SerialNumber: 0000:00:05.1 [ 5.810271] hub 3-0:1.0: USB hub found [ 5.814110] hub 3-0:1.0: 2 ports detected -- Raymond J Clark |