Package: installation-reports
Boot method: CD (virtual)
Image version:
http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/amd64/iso-cd/debian-testing-amd64-netinst.isoDate: July 11, 2015
Machine: VirtualBox VM
Processor: Intel Core i7-2600K
Memory: 512 MB
Partitions: <df -Tl will do; the raw partition table is preferred>
Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/sda1 ext4 1931600 825488 989940 46% /
udev devtmpfs 10240 0 10240 0% /dev
tmpfs tmpfs 101264 4472 96792 5% /run
tmpfs tmpfs 253156 0 253156 0% /dev/shm
tmpfs tmpfs 5120 0 5120 0% /run/lock
tmpfs tmpfs 253156 0 253156 0% /sys/fs/cgroup
Output of lspci -knn (or lspci -nn):
00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma] [8086:1237] (rev 02)
00:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] [8086:7000]
00:01.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01)
Kernel driver in use: ata_piix
00:02.0 VGA compatible controller [0300]: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter [80ee:beef]
00:03.0 Ethernet controller [0200]: Intel Corporation 82540EM Gigabit Ethernet Controller [8086:100e] (rev 02)
Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter [8086:001e]
Kernel driver in use: e1000
00:04.0 System peripheral [0880]: InnoTek Systemberatung GmbH VirtualBox Guest Service [80ee:cafe]
00:05.0 Multimedia audio controller [0401]: Intel Corporation 82801AA AC'97 Audio Controller [8086:2415] (rev 01)
Subsystem: Intel Corporation Device [8086:0000]
Kernel driver in use: snd_intel8x0
00:06.0 USB controller [0c03]: Apple Inc. KeyLargo/Intrepid USB [106b:003f]
Kernel driver in use: ohci-pci
00:07.0 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 08)
00:0d.0 SATA controller [0106]: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] [8086:2829] (rev 02)
Kernel driver in use: ahci
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [E]
Comments/Problems:
Network non-functional after first boot, but works during install.
Problem appears to be that network interface is called eth0 in /etc/network/interfaces, but name after first boot is enp0s3. This is shell-only install.
Reinstalled several times, it's reproduced 100% of the time.
Problem seems to be related to this:
http://www.freedesktop.org/wiki/Software/systemd/PredictableNetworkInterfaceNames/I switched to terminal during install, and 80-net-setup-link.rules is not under /lib/udev/rules.d. So during install network interface is still called eth0, could that be the problem?
If I switch to terminal during install and do: ln -s /dev/null /target/etc/udev/rules.d/80-net-setup-link.rules
then old network names are used after first boot and network starts ok. But that's a step backwards... proper thing would be if the network name written to /target/etc/network/interfaces is correct on first boot.
Alternatively if I change eth0 to enp0s3 in /etc/network/interfaces after install, then ifup, that also fixes it.
My /etc/network/interfaces at first boot looks like:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp