[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#791710: marked as done (INSTALL REPORT (Wheezy on QNAP TS-420U))

Your message dated Wed, 8 Jul 2015 16:06:39 -0400
with message-id <20150708200639.GA29997@jirafa.cyrius.com>
and subject line Re: Bug#791710: INSTALL REPORT  (Wheezy on QNAP TS-420U)
has caused the Debian Bug report #791710,
regarding INSTALL REPORT  (Wheezy on QNAP TS-420U)
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
791710: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=791710
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: installation-reports

Boot method:  network
Image version: http://ftp.debian.org/debian/dists/Debian7.8/main/installer-armel/current/images/kirkwood/network-console/qnap/ts-41x/ 
Date:  June 7, 2015

Machine:   QNAP TS-420U
Processor: Marvell 1.6 GHz
Memory:    1GB DDR3

Partitions:
Filesystem Type     1K-blocks   Used Available Use% Mounten
rootfs rootfs    19207764 686456  17545596   4% /
udev devtmpfs     10240      0     10240   0% /dev
tmpfs tmpfs        88048    192     87856   1% /run
/dev/disk/by-uuid/23d2cd0b-e894-4699-94b8-0ae0b8e4e54d ext4 19207764 686456 17545596 4% / 
tmpfs tmpfs         5120      0      5120   0% /run/lk
tmpfs tmpfs       566840      0    566840   0% /run/sm

Output of lspci -knn (or lspci -nn):
00:00.0 Host bridge [0600]: Marvell Technology Group Ltd. Device [11ab:6282] (rev 01) 
        Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
00:01.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. 88SX7042 PCI-e 4-port SATA-II [1) 
        Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
        Kernel driver in use: sata_mv
01:00.0 Host bridge [0600]: Marvell Technology Group Ltd. Device [11ab:6282] (rev 01) 
        Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
01:01.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] (rev 0) Subsystem: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] 
        Kernel driver in use: xhci_hcd

Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Initial boot:           [O]
Detect network card:    [O]
Configure network:      [O]
Detect CD:              [ ]
Load installer modules: [O]
Detect hard drives:     [O]
Partition hard drives:  [O]
Install base system:    [O]
Clock/timezone setup:   [O]
User/password setup:    [O]
Install tasks:          [O]
Install boot loader:    [O]
Overall install:        [O]

Comments/Problems:
I have selected 'oldstabel' (=wheezy) during installation (expert mode).
Used RAID1 for Debian installation:
#Personalities : [raid1]
md0 : active raid1 sdc2[5](S) sdb2[4] sda2[0] sdd2[3]
      19514240 blocks super 1.2 [3/3] [UUU]
The system is able to boot from any (active) disk which has been tested by removing two active disks before boot several times (the spare disk is than used for recovery). 
The systems works fine ...
NO PROBLEMS

Attachment: smime.p7s
Description: S/MIME Cryptographic Signature


--- End Message ---
--- Begin Message --- 
* Peter Nagel <peter.nagel@kit.edu> [2015-07-07 20:34]:
> Install boot loader:    [O]
> Overall install:        [O]
> 
> The systems works fine ...
> NO PROBLEMS

I'm closing this report since there were no problems.

Thanks.

-- 
Martin Michlmayr
http://www.cyrius.com/

--- End Message ---
Reply to: