--- Begin Message ---
Package: installation-reports
Boot method: netboot image (loaded from a USB stick)
Image version: local daily d-i build based on
git c16e202896206d5e7d1427c09e9a9044ea87471c
Date: 2015-03-14
Machine: LeMaker Banana Pro
Processor: Allwinner A20 (2x Cortex A7)
Memory: 1GB
Console: serial console, 115200 baud
U-Boot: U-Boot 2014.10+dfsg1-4
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
The installation was done to a 16GB Micro-SD card using serial console and
worked without problems; network (Gigabit ethernet) and the USB host ports
work as expected. The onboard SDIO WLAN module requires non-free firmware
and has not been tested.
The output of dmesg on the system:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.16.0-4-armmp-lpae (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt7-1 (2015-03-01)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=30c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: LeMaker Banana Pro
[ 0.000000] Forcing write-allocate cache policy for SMP
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0a197c0, node_mem_map eeff9000
[ 0.000000] DMA zone: 1520 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 528 pages used for memmap
[ 0.000000] HighMem zone: 67584 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] PERCPU: Embedded 9 pages/cpu @eefcf000 s12672 r8192 d16000 u36864
[ 0.000000] pcpu-alloc: s12672 r8192 d16000 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
[ 0.000000] Kernel command line: live-installer/enable=false suite=sid console=ttyS0,115200 quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1016280K/1048576K available (6588K kernel code, 842K rwdata, 2236K rodata, 700K init, 397K bss, 32296K reserved, 270336K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc08a6480 (8826 kB)
.init : 0xc08a7000 - 0xc0956180 ( 701 kB)
.data : 0xc0958000 - 0xc0a2a808 ( 843 kB)
.bss : 0xc0a2a808 - 0xc0a8dcb4 ( 398 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000018] Switching to timer-based delay loop
[ 0.001013] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[ 0.001402] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[ 0.001860] Console: colour dummy device 80x30
[ 0.001897] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.001913] pid_max: default: 32768 minimum: 301
[ 0.002048] Security Framework initialized
[ 0.002120] AppArmor: AppArmor disabled by boot time parameter
[ 0.002129] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.002211] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002224] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.003205] Initializing cgroup subsys memory
[ 0.003242] Initializing cgroup subsys devices
[ 0.003282] Initializing cgroup subsys freezer
[ 0.003300] Initializing cgroup subsys net_cls
[ 0.003333] Initializing cgroup subsys blkio
[ 0.003357] Initializing cgroup subsys perf_event
[ 0.003372] Initializing cgroup subsys net_prio
[ 0.003463] CPU: Testing write buffer coherency: ok
[ 0.003513] ftrace: allocating 23607 entries in 70 pages
[ 0.039473] /cpus/cpu@0 missing clock-frequency property
[ 0.039509] /cpus/cpu@1 missing clock-frequency property
[ 0.039524] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.039768] Setting up static identity map for 0x405eb358 - 0x405eb3b0
[ 0.049461] CPU1: Booted secondary processor
[ 0.049516] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.049631] Brought up 2 CPUs
[ 0.049659] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.049665] CPU: All CPU(s) started in HYP mode.
[ 0.049671] CPU: Virtualization extensions available.
[ 0.050403] devtmpfs: initialized
[ 0.054910] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.060853] pinctrl core: initialized pinctrl subsystem
[ 0.061375] regulator-dummy: no parameters
[ 0.067693] NET: Registered protocol family 16
[ 0.068088] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.076578] No ATAGs?
[ 0.076635] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.076648] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.076825] EXYNOS: PMU not supported
[ 0.077659] Serial: AMBA PL011 UART driver
[ 0.099061] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
[ 0.099091] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5
[ 0.099661] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[ 0.099684] platform usb1-vbus: Driver reg-fixed-voltage requests probe deferral
[ 0.099712] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[ 0.099726] platform usb2-vbus: Driver reg-fixed-voltage requests probe deferral
[ 0.099949] vcc3v0: 3000 mV
[ 0.100220] vcc3v3: 3300 mV
[ 0.100319] reg-fixed-voltage gmac-3v3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/gmac_power_pin@0, deferring probe
[ 0.100337] platform gmac-3v3: Driver reg-fixed-voltage requests probe deferral
[ 0.100362] reg-fixed-voltage vmmc3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/vmmc3_pin@0, deferring probe
[ 0.100375] platform vmmc3: Driver reg-fixed-voltage requests probe deferral
[ 0.101837] vgaarb: loaded
[ 0.102415] usbcore: registered new interface driver usbfs
[ 0.102486] usbcore: registered new interface driver hub
[ 0.102742] usbcore: registered new device driver usb
[ 0.103449] media: Linux media interface: v0.10
[ 0.103586] Linux video capture interface: v2.00
[ 0.103700] pps_core: LinuxPPS API ver. 1 registered
[ 0.103708] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.103738] PTP clock support registered
[ 0.105373] Switched to clocksource arch_sys_counter
[ 0.156336] NET: Registered protocol family 2
[ 0.157701] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.157793] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.157914] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.157999] TCP: reno registered
[ 0.158014] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158074] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158398] NET: Registered protocol family 1
[ 0.158468] PCI: CLS 0 bytes, default 64
[ 0.159033] Unpacking initramfs...
[ 1.144544] Freeing initrd memory: 12304K (cf3fb000 - cffff000)
[ 1.145194] kvm [1]: interrupt-controller@1c84000 IRQ25
[ 1.145616] kvm [1]: timer IRQ27
[ 1.145644] kvm [1]: Hyp mode initialized successfully
[ 1.146323] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
[ 1.148206] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.148360] audit: initializing netlink subsys (disabled)
[ 1.148472] audit: type=2000 audit(1.132:1): initialized
[ 1.149803] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.149896] zbud: loaded
[ 1.150343] VFS: Disk quotas dquot_6.5.2
[ 1.150416] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.150675] msgmni has been set to 1480
[ 1.152450] alg: No test for stdrng (krng)
[ 1.152589] bounce: pool size: 64 pages
[ 1.152703] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.152944] io scheduler noop registered
[ 1.152963] io scheduler deadline registered
[ 1.153128] io scheduler cfq registered (default)
[ 1.156631] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 1.159059] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.161178] console [ttyS0] disabled
[ 1.181388] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[ 1.199675] console [ttyS0] enabled
[ 1.221743] dw-apb-uart 1c28800.serial: Couldn't set LCR to 0
[ 1.228532] dw-apb-uart 1c28800.serial: Couldn't set LCR to 0
[ 1.234311] 1c28800.serial: ttyS1 at MMIO 0x1c28800 (irq = 35, base_baud = 1500000) is a U6_16550A
[ 1.256252] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0
[ 1.263041] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0
[ 1.268816] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 52, base_baud = 1500000) is a U6_16550A
[ 1.269283] Serial: AMBA driver
[ 1.269694] Serial: IMX driver
[ 1.273773] mousedev: PS/2 mouse device common for all mice
[ 1.275412] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[ 1.275428] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 1.276569] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.276682] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.277440] usbcore: registered new interface driver usbhid
[ 1.277450] usbhid: USB HID core driver
[ 1.278300] TCP: cubic registered
[ 1.278425] NET: Registered protocol family 10
[ 1.279572] mip6: Mobile IPv6
[ 1.279606] NET: Registered protocol family 17
[ 1.279643] mpls_gso: MPLS GSO support
[ 1.279793] ThumbEE CPU extension supported.
[ 1.279824] Registering SWP/SWPB emulation handler
[ 1.280646] registered taskstats version 1
[ 1.281830] usb1-vbus: 5000 mV
[ 1.282345] usb2-vbus: 5000 mV
[ 1.282746] gmac-3v3: 3300 mV
[ 1.283136] vmmc3: 3300 mV
[ 1.283565] sunxi-rtc 1c20d00.rtc: setting system clock to 2015-03-14 21:11:04 UTC (1426367464)
[ 1.288161] PM: Hibernation image not present or could not be loaded.
[ 1.288202] vmmc3: disabling
[ 1.288218] gmac-3v3: disabling
[ 1.288226] usb2-vbus: disabling
[ 1.288234] usb1-vbus: disabling
[ 1.288241] vcc3v3: disabling
[ 1.288248] vcc3v0: disabling
[ 1.289590] Freeing unused kernel memory: 700K (c08a7000 - c0956000)
[ 1.363671] systemd-udevd[61]: starting version 215
[ 1.366482] random: systemd-udevd urandom read with 0 bits of entropy available
[ 1.429344] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
[ 1.437799] sunxi-mmc 1c0f000.mmc: Got CD GPIO #234.
[ 1.463036] SCSI subsystem initialized
[ 1.477730] sunxi-mmc 1c0f000.mmc: base:0xf00cc000 irq:64
[ 1.478383] sunxi-mmc 1c12000.mmc: No vqmmc regulator found
[ 1.495890] libata version 3.00 loaded.
[ 1.513485] sunxi-mmc 1c12000.mmc: base:0xf0186000 irq:67
[ 1.521549] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 1.524277] mmc0: new high speed SDHC card at address 0007
[ 1.527559] mmcblk0: mmc0:0007 SD16G 14.6 GiB
[ 1.534956] mmcblk0: p1 p2 p3 < p5 >
[ 1.543021] sunxi-mmc 1c12000.mmc: smc 1 err, cmd 8, RTO !!
[ 1.560055] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.561770] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.563447] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.566433] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.584216] mmc1: new high speed SDIO card at address 0001
[ 1.617504] stmmaceth 1c50000.ethernet: no reset control found
[ 1.617531] Ring mode enabled
[ 1.617539] No HW DMA feature register supported
[ 1.617547] Normal descriptors
[ 1.617553] TX Checksum insertion supported
[ 1.637699] libphy: stmmac: probed
[ 1.637728] eth0: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[ 1.637738] eth0: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[ 1.681488] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 1.681519] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 1.681584] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.681601] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 1.683372] scsi0 : ahci_platform
[ 1.683861] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[ 2.001416] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.046071] PM: Starting manual resume from disk
[ 2.046107] PM: Hibernation image partition 179:5 present
[ 2.046114] PM: Looking for hibernation image.
[ 2.047488] PM: Image not found (code -22)
[ 2.047499] PM: Hibernation image not present or could not be loaded.
[ 2.296682] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.154719] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 3.577753] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 3.579264] systemd-udevd[159]: starting version 215
[ 3.846831] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.851446] ehci-platform: EHCI generic platform driver
[ 3.851882] ehci-platform 1c14000.usb: EHCI Host Controller
[ 3.853994] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[ 3.854195] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000
[ 3.867188] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 3.867550] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.867567] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.867577] usb usb1: Product: EHCI Host Controller
[ 3.867587] usb usb1: Manufacturer: Linux 3.16.0-4-armmp-lpae ehci_hcd
[ 3.867597] usb usb1: SerialNumber: 1c14000.usb
[ 3.868907] hub 1-0:1.0: USB hub found
[ 3.868999] hub 1-0:1.0: 1 port detected
[ 3.870028] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.870035] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 3.879233] ohci-platform: OHCI generic platform driver
[ 3.880419] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[ 3.880626] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000
[ 3.889483] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 3.889823] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.889840] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.889850] usb usb2: Product: EHCI Host Controller
[ 3.889860] usb usb2: Manufacturer: Linux 3.16.0-4-armmp-lpae ehci_hcd
[ 3.889869] usb usb2: SerialNumber: 1c1c000.usb
[ 3.890846] hub 2-0:1.0: USB hub found
[ 3.890921] hub 2-0:1.0: 1 port detected
[ 3.891835] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 3.893479] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[ 3.893659] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400
[ 3.953723] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.953749] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.953760] usb usb3: Product: Generic Platform OHCI controller
[ 3.953770] usb usb3: Manufacturer: Linux 3.16.0-4-armmp-lpae ohci_hcd
[ 3.953780] usb usb3: SerialNumber: 1c14400.usb
[ 3.954860] hub 3-0:1.0: USB hub found
[ 3.954958] hub 3-0:1.0: 1 port detected
[ 3.955791] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 3.957205] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 3.957437] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400
[ 4.024202] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.024229] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.024241] usb usb4: Product: Generic Platform OHCI controller
[ 4.024251] usb usb4: Manufacturer: Linux 3.16.0-4-armmp-lpae ohci_hcd
[ 4.024261] usb usb4: SerialNumber: 1c1c400.usb
[ 4.025589] hub 4-0:1.0: USB hub found
[ 4.025691] hub 4-0:1.0: 1 port detected
[ 4.030456] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 4.038914] cfg80211: Calling CRDA to update world regulatory domain
[ 4.089159] brcmfmac_sdio mmc1:0001:1: firmware: failed to load brcm/brcmfmac43362-sdio.bin (-2)
[ 4.265903] Adding 696316k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:696316k SSFS
[ 4.345891] random: nonblocking pool is initialized
[ 4.384041] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
[ 4.475666] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 4.537218] systemd-journald[141]: Received request to flush runtime journal from PID 1
[ 4.801230] No MAC Management Counters available
[ 5.114568] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
[ 5.378919] RPC: Registered named UNIX socket transport module.
[ 5.378944] RPC: Registered udp transport module.
[ 5.378951] RPC: Registered tcp transport module.
[ 5.378957] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 5.399009] FS-Cache: Loaded
[ 5.440945] FS-Cache: Netfs 'nfs' registered for caching
[ 5.497726] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 6.126448] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
[ 10.789758] stmmaceth 1c50000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Regards,
Karsten
--
Gem. Par. 28 Abs. 4 Bundesdatenschutzgesetz widerspreche ich der Nutzung
sowie der Weitergabe meiner personenbezogenen Daten für Zwecke der
Werbung sowie der Markt- oder Meinungsforschung.
--- End Message ---