--- Begin Message ---
Package: installation-reports
Boot method: hd-media + CD image on a USB stick
hd-media version: http://d-i.debian.org/daily-images/armhf/20150207-05:30/hd-media/hd-media.tar.gz
CD version: Debian GNU/Linux testing "Jessie" - Official Snapshot armhf CD Binary-1 20150202-10:45
from http://cdimage.debian.org/cdimage/weekly-builds/armhf/jigdo-cd/debian-testing-armhf-CD-1.jigdo,
dated 2015-02-02 12:06
Date: 2015-02-07
Machine: Olimex A20-OLinuXino-LIME
Processor: Allwinner A20 (2x Cortex A7)
Memory: 512MB
Console: serial console, 115200 baud
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
The installation was done to a 16GB Micro-SD card using serial
console (on the UART0 header) and worked without problems;
network (100MBit) and the USB host ports work as expected.
Partitioning was done using the "guided partitioning, all files
in one partition" option. I have not tested using a SATA disk
with the board due to lack of a SATA power cable that fits into
the board's SATA power connector (2-pin JST-style).
As an informational note: due to bug #773645 (lack of u-boot
tools on the first armhf CD), hd-media/CD installations on armhf
platforms currently require network connectivity during the
installation process; pure offline installations are not possible
with hd-media/CD at the moment.
dmesg output:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.16.0-4-armmp-lpae (debian-kernel@lists.debian.org) (gcc version 4.8.3 (Debian 4.8.3-16) ) #1 SMP Debian 3.16.7-ckt2-1 (2014-12-08)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=30c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Olimex A20-OLinuXino-LIME
[ 0.000000] Forcing write-allocate cache policy for SMP
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c0a0cb00, node_mem_map dfbf9000
[ 0.000000] DMA zone: 1024 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 131072 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] PERCPU: Embedded 9 pages/cpu @dfbd4000 s13312 r8192 d15360 u36864
[ 0.000000] pcpu-alloc: s13312 r8192 d15360 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 quiet
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 497040K/524288K available (6562K kernel code, 838K rwdata, 2216K rodata, 701K init, 396K bss, 27248K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc089aeb8 (8780 kB)
.init : 0xc089b000 - 0xc094a400 ( 701 kB)
.data : 0xc094c000 - 0xc0a1dab8 ( 839 kB)
.bss : 0xc0a1dab8 - 0xc0a80eb4 ( 397 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000019] Switching to timer-based delay loop
[ 0.001002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[ 0.001363] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[ 0.001801] Console: colour dummy device 80x30
[ 0.001837] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.001853] pid_max: default: 32768 minimum: 301
[ 0.001989] Security Framework initialized
[ 0.002063] AppArmor: AppArmor disabled by boot time parameter
[ 0.002073] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.002155] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002167] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003120] Initializing cgroup subsys memory
[ 0.003155] Initializing cgroup subsys devices
[ 0.003195] Initializing cgroup subsys freezer
[ 0.003214] Initializing cgroup subsys net_cls
[ 0.003247] Initializing cgroup subsys blkio
[ 0.003273] Initializing cgroup subsys perf_event
[ 0.003290] Initializing cgroup subsys net_prio
[ 0.003381] CPU: Testing write buffer coherency: ok
[ 0.003435] ftrace: allocating 23541 entries in 70 pages
[ 0.039639] /cpus/cpu@0 missing clock-frequency property
[ 0.039674] /cpus/cpu@1 missing clock-frequency property
[ 0.039689] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.039936] Setting up static identity map for 0x405e5f98 - 0x405e5ff0
[ 0.049549] CPU1: Booted secondary processor
[ 0.049604] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.049723] Brought up 2 CPUs
[ 0.049747] SMP: Total of 2 processors activated.
[ 0.049754] CPU: All CPU(s) started in HYP mode.
[ 0.049759] CPU: Virtualization extensions available.
[ 0.050507] devtmpfs: initialized
[ 0.054951] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.060828] pinctrl core: initialized pinctrl subsystem
[ 0.061355] regulator-dummy: no parameters
[ 0.067145] NET: Registered protocol family 16
[ 0.067580] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.074686] No ATAGs?
[ 0.074735] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.074748] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.074912] EXYNOS: PMU not supported
[ 0.075945] Serial: AMBA PL011 UART driver
[ 0.094717] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
[ 0.094749] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5
[ 0.095199] reg-fixed-voltage ahci-5v: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
[ 0.095219] platform ahci-5v: Driver reg-fixed-voltage requests probe deferral
[ 0.095245] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[ 0.095259] platform usb1-vbus: Driver reg-fixed-voltage requests probe deferral
[ 0.095279] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[ 0.095292] platform usb2-vbus: Driver reg-fixed-voltage requests probe deferral
[ 0.095509] vcc3v0: 3000 mV
[ 0.095845] vcc3v3: 3300 mV
[ 0.096992] vgaarb: loaded
[ 0.097519] usbcore: registered new interface driver usbfs
[ 0.097591] usbcore: registered new interface driver hub
[ 0.097851] usbcore: registered new device driver usb
[ 0.098480] media: Linux media interface: v0.10
[ 0.098555] Linux video capture interface: v2.00
[ 0.098666] pps_core: LinuxPPS API ver. 1 registered
[ 0.098674] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.098706] PTP clock support registered
[ 0.100338] Switched to clocksource arch_sys_counter
[ 0.151913] NET: Registered protocol family 2
[ 0.153236] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.153294] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.153361] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.153433] TCP: reno registered
[ 0.153450] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.153486] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.153805] NET: Registered protocol family 1
[ 0.153877] PCI: CLS 0 bytes, default 64
[ 0.154422] Unpacking initramfs...
[ 1.107279] Freeing initrd memory: 11816K (cf475000 - cffff000)
[ 1.107896] kvm [1]: interrupt-controller@1c84000 IRQ25
[ 1.108236] kvm [1]: timer IRQ27
[ 1.108260] kvm [1]: Hyp mode initialized successfully
[ 1.109007] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
[ 1.110910] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.111080] audit: initializing netlink subsys (disabled)
[ 1.111188] audit: type=2000 audit(1.096:1): initialized
[ 1.112671] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.112772] zbud: loaded
[ 1.113215] VFS: Disk quotas dquot_6.5.2
[ 1.113293] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.113565] msgmni has been set to 993
[ 1.115300] alg: No test for stdrng (krng)
[ 1.115466] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.115700] io scheduler noop registered
[ 1.115718] io scheduler deadline registered
[ 1.115878] io scheduler cfq registered (default)
[ 1.119229] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 1.121623] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.123678] console [ttyS0] disabled
[ 1.143877] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[ 1.162152] console [ttyS0] enabled
[ 1.162597] Serial: AMBA driver
[ 1.162905] Serial: IMX driver
[ 1.166708] mousedev: PS/2 mouse device common for all mice
[ 1.168177] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[ 1.168193] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 1.169336] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.169454] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.170144] usbcore: registered new interface driver usbhid
[ 1.170153] usbhid: USB HID core driver
[ 1.170825] TCP: cubic registered
[ 1.170953] NET: Registered protocol family 10
[ 1.172133] mip6: Mobile IPv6
[ 1.172167] NET: Registered protocol family 17
[ 1.172206] mpls_gso: MPLS GSO support
[ 1.172379] ThumbEE CPU extension supported.
[ 1.172415] Registering SWP/SWPB emulation handler
[ 1.173255] registered taskstats version 1
[ 1.174354] ahci-5v: 5000 mV
[ 1.174859] usb1-vbus: 5000 mV
[ 1.175280] usb2-vbus: 5000 mV
[ 1.175679] sunxi-rtc 1c20d00.rtc: setting system clock to 2015-02-07 12:35:07 UTC (1423312507)
[ 1.180452] PM: Hibernation image not present or could not be loaded.
[ 1.180499] usb2-vbus: disabling
[ 1.180515] usb1-vbus: disabling
[ 1.180525] ahci-5v: disabling
[ 1.180533] vcc3v3: disabling
[ 1.180540] vcc3v0: disabling
[ 1.181825] Freeing unused kernel memory: 700K (c089b000 - c094a000)
[ 1.255433] systemd-udevd[60]: starting version 215
[ 1.258335] random: systemd-udevd urandom read with 0 bits of entropy available
[ 1.323715] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
[ 1.331294] SCSI subsystem initialized
[ 1.336811] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225.
[ 1.348586] libata version 3.00 loaded.
[ 1.368825] sunxi-mmc 1c0f000.mmc: base:0xe0902000 irq:64
[ 1.412540] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 1.412568] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 1.412583] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 1.412649] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.412666] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 1.414024] scsi0 : ahci_platform
[ 1.414511] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[ 1.415711] stmmaceth 1c50000.ethernet: no regulator found
[ 1.415790] stmmaceth 1c50000.ethernet: no reset control found
[ 1.415804] Ring mode enabled
[ 1.415813] No HW DMA feature register supported
[ 1.415820] Normal descriptors
[ 1.415827] TX Checksum insertion supported
[ 1.419854] mmc0: new high speed SDHC card at address 0007
[ 1.424606] mmcblk0: mmc0:0007 SD16G 14.4 GiB
[ 1.427711] mmcblk0: p1 p2 p3 < p5 >
[ 1.442544] libphy: stmmac: probed
[ 1.442569] eth0: PHY ID 00008201 at 1 IRQ POLL (stmmac-0:01) active
[ 1.736379] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.811981] PM: Starting manual resume from disk
[ 1.812016] PM: Hibernation image partition 179:5 present
[ 1.812023] PM: Looking for hibernation image.
[ 1.813560] PM: Image not found (code -22)
[ 1.813575] PM: Hibernation image not present or could not be loaded.
[ 1.870234] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.368228] systemd[1]: /etc/mtab is not a symlink or not pointing to /proc/self/mounts. This is not supported anymore. Please make sure to replace this file by a symlink to avoid incorrect or misleading mount(8) output.
[ 2.782087] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 3.227139] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 3.289131] systemd-udevd[152]: starting version 215
[ 3.559863] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.575965] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.578187] ehci-platform: EHCI generic platform driver
[ 3.578603] ehci-platform 1c14000.usb: EHCI Host Controller
[ 3.579114] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[ 3.579320] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000
[ 3.585428] ohci-platform: OHCI generic platform driver
[ 3.588476] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 3.589110] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.589133] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.589144] usb usb1: Product: EHCI Host Controller
[ 3.589155] usb usb1: Manufacturer: Linux 3.16.0-4-armmp-lpae ehci_hcd
[ 3.589164] usb usb1: SerialNumber: 1c14000.usb
[ 3.590332] hub 1-0:1.0: USB hub found
[ 3.590440] hub 1-0:1.0: 1 port detected
[ 3.591511] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 3.591973] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[ 3.592168] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000
[ 3.603922] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 3.604491] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.604510] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.604521] usb usb2: Product: EHCI Host Controller
[ 3.604531] usb usb2: Manufacturer: Linux 3.16.0-4-armmp-lpae ehci_hcd
[ 3.604540] usb usb2: SerialNumber: 1c1c000.usb
[ 3.605827] hub 2-0:1.0: USB hub found
[ 3.608862] hub 2-0:1.0: 1 port detected
[ 3.611714] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 3.612059] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 3.613091] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[ 3.613236] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400
[ 3.672731] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.672757] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.672767] usb usb3: Product: Generic Platform OHCI controller
[ 3.672778] usb usb3: Manufacturer: Linux 3.16.0-4-armmp-lpae ohci_hcd
[ 3.672787] usb usb3: SerialNumber: 1c14400.usb
[ 3.676187] hub 3-0:1.0: USB hub found
[ 3.676289] hub 3-0:1.0: 1 port detected
[ 3.699382] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 3.700063] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 3.700203] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400
[ 3.758793] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.758820] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.758830] usb usb4: Product: Generic Platform OHCI controller
[ 3.758841] usb usb4: Manufacturer: Linux 3.16.0-4-armmp-lpae ohci_hcd
[ 3.758850] usb usb4: SerialNumber: 1c1c400.usb
[ 3.759964] hub 4-0:1.0: USB hub found
[ 3.760050] hub 4-0:1.0: 1 port detected
[ 3.862042] Adding 691196k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:691196k SSFS
[ 3.904561] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 4.039644] usb 1-1: New USB device found, idVendor=090c, idProduct=1000
[ 4.039669] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.039680] usb 1-1: Product: Intenso Rainbow Line
[ 4.039690] usb 1-1: Manufacturer: SMI Technology
[ 4.039700] usb 1-1: SerialNumber: XXXXXXXXXXXXXX
[ 4.076489] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
[ 4.098290] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.099626] scsi1 : usb-storage 1-1:1.0
[ 4.100211] usbcore: registered new interface driver usb-storage
[ 4.103074] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 4.167802] systemd-journald[131]: Received request to flush runtime journal from PID 1
[ 4.495479] No MAC Management Counters available
[ 4.499996] random: nonblocking pool is initialized
[ 5.161022] RPC: Registered named UNIX socket transport module.
[ 5.161050] RPC: Registered udp transport module.
[ 5.161057] RPC: Registered tcp transport module.
[ 5.161064] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 5.182233] FS-Cache: Loaded
[ 5.226199] FS-Cache: Netfs 'nfs' registered for caching
[ 5.286297] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 5.613892] scsi 1:0:0:0: Direct-Access Intenso Rainbow PQ: 0 ANSI: 4
[ 5.669087] sd 1:0:0:0: [sda] 15605760 512-byte logical blocks: (7.99 GB/7.44 GiB)
[ 5.670286] sd 1:0:0:0: [sda] Write Protect is off
[ 5.670320] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 5.671558] sd 1:0:0:0: [sda] No Caching mode page found
[ 5.677024] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 5.695163] sda: sda1
[ 5.702811] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 5.714041] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 6.484634] stmmaceth 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
--
Gem. Par. 28 Abs. 4 Bundesdatenschutzgesetz widerspreche ich der Nutzung
sowie der Weitergabe meiner personenbezogenen Daten für Zwecke der
Werbung sowie der Markt- oder Meinungsforschung.
--- End Message ---