Bug#690586: installation-reports: NVIDIA GF108 [Quadro 1000M] 10de:0dfa (rev a1) X fails with nouveau/linux-3.2
On Mon, Nov 19, 2012 at 10:01:05PM +0100, Sven Joachim wrote:
[...]
> Do you have another computer where you can capture kernel messages via
> netconsole? A short HOWTO for netconsole is on
> http://blog.mraw.org/2010/11/08/Debugging_using_netconsole, also see
> Documentation/networking/netconsole.txt in the kernel source.
It's attached.
Cheers,
Andi
[ 0.007880] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.007881] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.008158] mce: CPU supports 9 MCE banks
[ 0.008290] CPU0: Thermal monitoring enabled (TM1)
[ 0.008418] using mwait in idle threads.
[ 0.008992] ACPI: Core revision 20110623
[ 0.030623] DMAR: Host address width 36
[ 0.030742] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[ 0.030871] IOMMU 0: reg_base_addr fed91000 ver 1:0 cap c9008020660262 ecap f0105a
[ 0.031038] DMAR: RMRR base: 0x000000bf69a000 end: 0x000000bf6b9fff
[ 0.031235] IOAPIC id 0 under DRHD base 0xfed91000 IOMMU 0
[ 0.031361] HPET id 0 under DRHD base 0xfed91000
[ 0.031482] HPET id 0 under DRHD base 0xfed91000
[ 0.031603] HPET id 0 under DRHD base 0xfed91000
[ 0.031725] HPET id 0 under DRHD base 0xfed91000
[ 0.031846] HPET id 0 under DRHD base 0xfed91000
[ 0.031968] HPET id 0 under DRHD base 0xfed91000
[ 0.032088] HPET id 0 under DRHD base 0xfed91000
[ 0.032209] HPET id 0 under DRHD base 0xfed91000
[ 0.032417] Enabled IRQ remapping in x2apic mode
[ 0.032538] Enabling x2apic
[ 0.032652] Enabled x2apic
[ 0.032777] Switched APIC routing to cluster x2apic.
[ 0.033340] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.073088] CPU0: Intel(R) Core(TM) i7-2760QM CPU @ 2.40GHz stepping 07
[ 0.179657] Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
[ 0.180034] PEBS disabled due to CPU errata.
[ 0.187430] ... version: 3
[ 0.187549] ... bit width: 48
[ 0.187669] ... generic registers: 4
[ 0.187788] ... value mask: 0000ffffffffffff
[ 0.187911] ... max period: 000000007fffffff
[ 0.188035] ... fixed-purpose events: 3
[ 0.188154] ... event mask: 000000070000000f
[ 0.188410] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.188623] Booting Node 0, Processors #1
[ 0.299552] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.299778] #2
[ 0.407466] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.407686] #3
[ 0.515272] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.515488] #4
[ 0.623076] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.623294] #5
[ 0.730988] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.731207] #6
[ 0.838793] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.839011] #7 Ok.
[ 0.946630] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.946782] Brought up 8 CPUs
[ 0.946896] Total of 8 processors activated (38312.50 BogoMIPS).
[ 0.954270] devtmpfs: initialized
[ 0.957684] PM: Registering ACPI NVS region at bf6bd000 (1048576 bytes)
[ 0.957981] print_constraints: dummy:
[ 0.958151] NET: Registered protocol family 16
[ 0.958354] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.958524] ACPI: bus type pci registered
[ 0.958720] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.958894] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.978885] PCI: Using configuration type 1 for base access
[ 0.979971] bio: create slab <bio-0> at 0
[ 0.980181] ACPI: Added _OSI(Module Device)
[ 0.980301] ACPI: Added _OSI(Processor Device)
[ 0.980421] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.980544] ACPI: Added _OSI(Processor Aggregator Device)
[ 2.957185] ACPI: Interpreter enabled
[ 3.307695] VFS: Disk quotas dquot_6.5.2
[ 3.307837] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 3.315327] msgmni has been set to 32073
[ 3.315578] alg: No test for stdrng (krng)
[ 3.315722] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.315882] io scheduler noop registered
[ 3.315994] io scheduler deadline registered
[ 3.316133] io scheduler cfq registered (default)
[ 38.356750] EXT4-fs (dm-1): INFO: recovery required on readonly filesystem
[ 38.356885] EXT4-fs (dm-1): write access will be enabled during recovery
[ 40.886481] iTCO_vendor_support: vendor-support=0
[ 40.891634] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 40.891835] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 40.892047] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 40.904133] parport_pc 00:09: reported by Plug and Play ACPI
[ 40.904351] parport0: PC-style at 0x378 (0x778), irq 5 [PCSPP,TRISTATE]
[ 40.939369] [drm] Initialized drm 1.1.0 20060810
[ 40.982166] wmi: Mapper loaded
[ 41.025398] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 41.025760] usbcore: registered new interface driver btusb
[ 41.041680] tpm_tis 00:04: 1.2 TPM (device-id 0xB, rev-id 16)
[ 42.075577] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1c0b1, caps: 0xd40033/0x640000/0xa0400
[ 43.662287] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 43.678521] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[ 43.679444] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[ 43.680311] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input18
[ 43.681176] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input19
[ 45.172079] loop: module loaded
[ 55.228639] ADDRCONF(NETDEV_UP): virbr0: link is not ready
[ 56.230056] Ebtables v2.0 registered
[ 56.325871] ip6_tables: (C) 2000-2006 Netfilter Core Team
Reply to: