[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#678264: "No common CD-ROM drive was detected" from debian-wheezy-DI-a1-sparc-netinst.iso on LDOM



Package: installation-reports

Boot method: debian-wheezy-DI-a1-sparc-netinst.iso CD
Image version: debian-wheezy-DI-a1-sparc-netinst.iso
Date: Wed Jun 20 07:34:55 CDT 2012

Machine: Sun Enterprize T5120 as host LDOM server
Processor:
Memory:
Partitions: <df -Tl will do; the raw partition table is preferred>

Output of lspci -knn (or lspci -nn):

Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Initial boot:           [ ]
Detect network card:    [ ]
Configure network:      [ ]
Detect CD:              [ ]
Load installer modules: [ ]
Detect hard drives:     [ ]
Partition hard drives:  [ ]
Install base system:    [ ]
Clock/timezone setup:   [ ]
User/password setup:    [ ]
Install tasks:          [ ]
Install boot loader:    [ ]
Overall install:        [ ]

Comments/Problems:

Please see following logs capture from vt100 session. Problem was it
can't find CDROM.
I remember read it somewhere, This problem is caused by T5120 using
usb interface to connect to CDROM.
same problem with stable squeezy netinstall.



SPARC Enterprise T5120, No Keyboard
Copyright (c) 1998, 2010, Oracle and/or its affiliates. All rights reserved.
OpenBoot 4.30.9, 2048 MB memory available, Serial #83526033.
Ethernet address 0:14:4f:fa:81:91, Host ID: 84fa8191.



{0} ok

{0} ok boot vcdrom


Boot device: /virtual-devices@100/channel-devices@200/disk@1  File and args:
SILO Version 1.4.14
EXT2 superblock magic is wrong
EXT2 superblock magic is wrong
\

                  Welcome to Debian GNU/Linux wheezy!

This is a Debian installation CDROM, built on 20120512-00:53.
Keep it once you have installed your system, as you can boot from it
to repair the system on your hard disk if that ever becomes necessary.

WARNING: You should completely back up all of your hard disks before
  proceeding. The installation procedure can completely and irreversibly
  erase them! If you haven't made backups yet, remove the rescue CD from
  the drive and press L1-A to get back to the OpenBoot prompt.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted
by applicable law.

[ ENTER - Boot install ]   [ Type "expert" - Boot into expert mode ]
                           [ Type "rescue" - Boot into rescue mode ]
boot:

Allocated 64 Megs of memory at 0x40000000 for kernel
EXT2 superblock magic is wrong
Loaded kernel version 3.2.15
EXT2 superblock magic is wrong
Loading initial ramdisk (4854411 bytes at 0xC800000 phys, 0x40C00000 virt)...
\
[    0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.30.9 2010/07/16 09:01'
[    0.000000] PROMLIB: Root node compatible: sun4v
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-2-sparc64 (Debian 3.2.15-1)
(debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) )
#1 Sun Apr 15 17:44:17 UTC 2012
[    0.000000] bootconsole [earlyprom0] enabled
[    0.000000] ARCH: SUN4V
[    0.000000] Ethernet address: 00:14:4f:fa:81:91
[    0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[    0.000000] Remapping the kernel... done.
[    0.000000] OF stdout device is: /virtual-devices@100/console@1
[    0.000000] PROM: Built device tree with 23158 bytes of memory.
[    0.000000] MDESC: Size is 10640 bytes.
[    0.000000] PLATFORM: banner-name [SPARC Enterprise T5120]
[    0.000000] PLATFORM: name [SUNW,SPARC-Enterprise-T5120]
[    0.000000] PLATFORM: hostid [84fa8191]
[    0.000000] PLATFORM: serial# [00ab4130]
[    0.000000] PLATFORM: stick-frequency [457646c0]
[    0.000000] PLATFORM: mac-address [144ffa8191]
[    0.000000] PLATFORM: watchdog-resolution [1000 ms]
[    0.000000] PLATFORM: watchdog-max-timeout [31536000000 ms]
[    0.000000] PLATFORM: max-cpus [64]
[    0.000000] SUN4V: Mondo queue sizes [cpu(8192) dev(16384) r(8192) nr(256)]
[    0.000000] Top of RAM: 0x87f96000, Total RAM: 0x7fa80000
[    0.000000] Memory hole size: 133MB
[    0.000000] [0000010000000000-fffff80009000000] page_structs=131072
node=0 entry=0/8192
[    0.000000] [0000010000000000-fffff80009400000] page_structs=131072
node=0 entry=1/8192
[    0.000000] [0000010000800000-fffff80009800000] page_structs=131072
node=0 entry=2/8192
[    0.000000] [0000010000800000-fffff80009c00000] page_structs=131072
node=0 entry=3/8192
[    0.000000] [0000010001000000-fffff8000a000000] page_structs=131072
node=0 entry=4/8192
[    0.000000] [0000010001000000-fffff8000a400000] page_structs=131072
node=0 entry=5/8192
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00004200 -> 0x00043fcb
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00004200 -> 0x00043f3b
[    0.000000]     0: 0x00043fc3 -> 0x00043fc4
[    0.000000]     0: 0x00043fc7 -> 0x00043fcb
[    0.000000] Booting Linux...
[    0.000000] CPU CAPS: [flush,stbar,swap,muldiv,v9,blkinit,n2,mul32]
[    0.000000] CPU CAPS: [div32,v8plus,popc,vis,vis2,ASIBlkInit]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 259396
[    0.000000] Kernel command line:
[    0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 8, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 7, 1048576 bytes)
[    0.000000] Memory: 2053000k available (3488k kernel code, 1520k
data, 184k init) [fffff80000000000,0000000087f96000]
[    0.000000] NR_IRQS:255
[    0.000000] clocksource: mult[dbabc5] shift[24]
[    0.000000] clockevent: mult[952b25d1] shift[31]
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled, bootconsole disabled
[    0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.30.9 2010/07/16 09:01'
[    0.000000] PROMLIB: Root node compatible: sun4v
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-2-sparc64 (Debian 3.2.15-1)
(debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) )
#1 Sun Apr 15 17:44:17 UTC 2012
[    0.000000] bootconsole [earlyprom0] enabled
[    0.000000] ARCH: SUN4V
[    0.000000] Ethernet address: 00:14:4f:fa:81:91
[    0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[    0.000000] Remapping the kernel... done.
[    0.000000] OF stdout device is: /virtual-devices@100/console@1
[    0.000000] PROM: Built device tree with 23158 bytes of memory.
[    0.000000] MDESC: Size is 10640 bytes.
[    0.000000] PLATFORM: banner-name [SPARC Enterprise T5120]
[    0.000000] PLATFORM: name [SUNW,SPARC-Enterprise-T5120]
[    0.000000] PLATFORM: hostid [84fa8191]
[    0.000000] PLATFORM: serial# [00ab4130]
[    0.000000] PLATFORM: stick-frequency [457646c0]
[    0.000000] PLATFORM: mac-address [144ffa8191]
[    0.000000] PLATFORM: watchdog-resolution [1000 ms]
[    0.000000] PLATFORM: watchdog-max-timeout [31536000000 ms]
[    0.000000] PLATFORM: max-cpus [64]
[    0.000000] SUN4V: Mondo queue sizes [cpu(8192) dev(16384) r(8192) nr(256)]
[    0.000000] Top of RAM: 0x87f96000, Total RAM: 0x7fa80000
[    0.000000] Memory hole size: 133MB
[    0.000000] [0000010000000000-fffff80009000000] page_structs=131072
node=0 entry=0/8192
[    0.000000] [0000010000000000-fffff80009400000] page_structs=131072
node=0 entry=1/8192
[    0.000000] [0000010000800000-fffff80009800000] page_structs=131072
node=0 entry=2/8192
[    0.000000] [0000010000800000-fffff80009c00000] page_structs=131072
node=0 entry=3/8192
[    0.000000] [0000010001000000-fffff8000a000000] page_structs=131072
node=0 entry=4/8192
[    0.000000] [0000010001000000-fffff8000a400000] page_structs=131072
node=0 entry=5/8192
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00004200 -> 0x00043fcb
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00004200 -> 0x00043f3b
[    0.000000]     0: 0x00043fc3 -> 0x00043fc4
[    0.000000]     0: 0x00043fc7 -> 0x00043fcb
[    0.000000] Booting Linux...
[    0.000000] CPU CAPS: [flush,stbar,swap,muldiv,v9,blkinit,n2,mul32]
[    0.000000] CPU CAPS: [div32,v8plus,popc,vis,vis2,ASIBlkInit]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 259396
[    0.000000] Kernel command line:
[    0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 8, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 7, 1048576 bytes)
[    0.000000] Memory: 2053000k available (3488k kernel code, 1520k
data, 184k init) [fffff80000000000,0000000087f96000]
[    0.000000] NR_IRQS:255
[    0.000000] clocksource: mult[dbabc5] shift[24]
[    0.000000] clockevent: mult[952b25d1] shift[31]
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled, bootconsole disabled
[14591163.422684] Calibrating delay using timer specific routine..
2334.03 BogoMIPS (lpj=4668070)
[14591163.422735] pid_max: default: 32768 minimum: 301
[14591163.422961] Security Framework initialized
[14591163.422999] AppArmor: AppArmor disabled by boot time parameter
[14591163.423105] Mount-cache hash table entries: 512
[14591163.423572] Initializing cgroup subsys cpuacct
[14591163.423614] Initializing cgroup subsys memory
[14591163.423667] Initializing cgroup subsys devices
[14591163.423689] Initializing cgroup subsys freezer
[14591163.423709] Initializing cgroup subsys net_cls
[14591163.423730] Initializing cgroup subsys blkio
[14591163.423765] Initializing cgroup subsys perf_event
[14591163.424020] Performance events: Supported PMU type is 'niagara2'
[14591163.424982] devtmpfs: initialized
[14591163.425380] ldc.c:v1.1 (July 22, 2008)
[14591163.425966] print_constraints: dummy:
[14591163.426223] NET: Registered protocol family 16
[14591163.428255] VIO: Adding device channel-devices
[14591163.428341] VIO: Adding device vnet-port-0-0
[14591163.428423] VIO: Adding device vnet-port-0-1
[14591163.428502] VIO: Adding device vnet-port-0-2
[14591163.428579] VIO: Adding device vnet-port-0-3
[14591163.428655] VIO: Adding device vnet-port-0-4
[14591163.428750] VIO: Adding device vnet-port-0-5
[14591163.428840] VIO: Adding device vnet-port-0-6
[14591163.428925] VIO: Adding device vnet-port-0-7
[14591163.429008] VIO: Adding device vnet-port-0-8
[14591163.429092] VIO: Adding device vdc-port-0-0
[14591163.429179] VIO: Adding device vdc-port-1-0
[14591163.429261] VIO: Adding device vlds-port-0-0
[14591163.429344] VIO: Adding device ds-0
[14591163.430589] ds.c:v1.0 (Jul 11, 2007)
[14591163.430870] ds-0: ds_conn_reset() from 00000000004414b8
[14591163.434280] bio: create slab <bio-0> at 0
[14591163.434794] vgaarb: loaded
[14591163.435469] Switching to clocksource stick
[14591163.449829] NET: Registered protocol family 2
[14591163.450156] IP route cache hash table entries: 65536 (order: 6,
524288 bytes)
[14591163.451376] TCP established hash table entries: 262144 (order:
9, 4194304 bytes)
[14591163.465174] TCP bind hash table entries: 65536 (order: 6, 524288 bytes)
[14591163.466928] TCP: Hash tables configured (established 262144 bind 65536)
[14591163.466959] TCP reno registered
[14591163.466991] UDP hash table entries: 1024 (order: 2, 32768 bytes)
[14591163.467131] UDP-Lite hash table entries: 1024 (order: 2, 32768 bytes)
[14591163.467728] NET: Registered protocol family 1
[14591163.468009] Unpacking initramfs...
[14591164.073519] Freeing initrd memory: 4740k freed
[14591164.076029] audit: initializing netlink socket (disabled)
[14591164.076091] type=2000 audit(0.728:1): initialized
[14591164.175260] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[14591164.176309] VFS: Disk quotas dquot_6.5.2
[14591164.176475] Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
[14591164.176761] msgmni has been set to 4019
[14591164.177500] alg: No test for stdrng (krng)
[14591164.177639] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 253)
[14591164.177682] io scheduler noop registered
[14591164.177705] io scheduler deadline registered
[14591164.177795] io scheduler cfq registered (default)
[14591164.178836] f027a434: ttyS0 at I/O 0x0 (irq = 17) is a SUN4V HCONS
[14591164.179393] console [ttyHV0] enabled
[14591164.180073] [drm] Initialized drm 1.1.0 20060810
[14591164.181138] mousedev: PS/2 mouse device common for all mice
[14591164.182020] rtc-sun4v rtc-sun4v: rtc core: registered sun4v as rtc0
[14591164.183110] TCP cubic registered
[14591164.183361] NET: Registered protocol family 10
[14591164.186025] Mobile IPv6
[14591164.186054] NET: Registered protocol family 17
[14591164.186096] Registering the dns_resolver key type
[14591164.186220] registered taskstats version 1
[14591164.186368] rtc-sun4v rtc-sun4v: setting system clock to
2012-06-20 12:24:21 UTC (1340195061)
[14591164.186470] Initializing network drop monitor service
udevd[51]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices': No such file or directory

udevd[55]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vlds-port-0-0': No such file or directory

udevd[56]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-0': No such file or directory

udevd[54]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vdc-port-1-0': No such file or directory

udevd[53]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vdc-port-0-0': No such file or directory

udevd[65]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-2': No such file or directory

udevd[66]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-3': No such file or directory

udevd[67]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-4': No such file or directory

udevd[64]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-1': No such file or directory

udevd[68]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-5': No such file or directory

udevd[69]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-6': No such file or directory

udevd[70]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-7': No such file or directory

udevd[73]: failed to execute '/lib/udev/vio_type' 'vio_type --export
/devices/channel-devices/vnet-port-0-8': No such file or directory

Starting system log daemon: syslogd, klogd.



┌───────────────────────┤ [!!] Select a language ├────────────────────────┐
  │                                                                         │
  │ Choose the language to be used for the installation process. The        │
  │ selected language will also be the default language for the installed   │
  │ system.                                                                 │
  │                                                                         │
  │ Language:                                                               │
  │                                                                         │
  │                               C                                         │
  │                               English                                   │
  │                                                                         │
  │     <Go Back>                                                           │
  │                                                                         │
  └─────────────────────────────────────────────────────────────────────────┘



   ┌───────────────────┤ [!!] Detect and mount CD-ROM ├────────────────────┐
   │                                                                       │
   │ No common CD-ROM drive was detected.                                  │
   │                                                                       │
   │ You may need to load additional CD-ROM drivers from removable media,  │
   │ such as a driver floppy. If you have such media available now, insert │
   │ it, and continue. Otherwise, you will be given the option to manually │
   │ select CD-ROM modules.                                                │
   │                                                                       │
   │ Load CD-ROM drivers from removable media?                             │
   │                                                                       │
   │     <Yes>                                                    <No>     │
   │                                                                       │
   └───────────────────────────────────────────────────────────────────────┘





-- 
T.J. Yang



Reply to: